1705403026

12 11 10 9 7 8 5 6 4 3 2 1 25.4 H 7.6 H 1.2 (TAIL LENGTH) 3.80 24.8 SEE NOTE 10 G G 25.90 22.95 PIN A1 F F 11.36 8.44 SIGNAL HOLES REF B GROUND HOLE SEE NOTE 9 A BACKPLANE (REF) 1.06 4.40 2X 1.90 KEEP-OUT ZONE (2.1) 22.95 27.1 KEY SHOWN IN POSITION 'G' 25.90 14.05 16.00 D C B A NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN MIN GOLD IN CONTACT AREA, SELECTIVE TIN ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-170540-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-589. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-170535-0002 AND RSD-170532-XXXX FOR THE MATING HEADERS. 8. REFER TO MOLEX ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. GROUND PATHS ARE NOT DISCRETE CIRCUTIS WITHIN CONNECTOR DUE TO PRESENCE OF PLUS CLIP. 10. PART NUMBER 170540-3720 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 11. MINIMUM BOARD THICKNESS IS 1.0 mm FOR COMPLIANT PIN FUNCTIONALITY. 12. WHEN USING MOLEX SUPPLIED #2-32 SCREW 73726-0000 (9.50 NOMINAL THREADABLE SCREW LENGTH), THE MAXIMUM BOARD THICKNESS IS 4.4 mm. 13. MARKING: LOCATED APPROXIMATELY AS SHOWN, PART NUMBER, DATE CODE, AND SERIAL NUMBER. DOCUMENT STATUS 12 P1 RELEASE DATE 11 2019/01/29 10 02:36:16 14.00 (FULLY MATED) PIN A1 1.70 MAX D ⌖ ⌀0.10 0.35 ⌀PTH OFFSET BETWEEN DC AND BP HOLE COLUMNS (SEE CHART) (18 HOLES PER COLUMN) SEE NOTE 3. C BACKPLANE (REF) BP PIN A1 (CONNECTOR SIDE) DAUGHTERCARD HOLE PATTERN B SYMBOLS = 0 = 0 = 0 8 7 6 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 C 9 ⌀2.45±0.04 UNPLATED HOLES 2X = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 ⌖ ⌀0.10 1.35 17X E ROW T ROW S ROW R ROW P ROW O ROW N ROW M ROW L ROW K ROW J ROW H ROW G ROW F ROW E ROW D ROW C ROW B ROW A BP ROW A E = 0 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 CURRENT REV DESC: EC NO: DRWN: CHK'D: APPR: INITIAL DRWN: APPR: 611164 DMORGAN TELO TELO REVISION: JLAURX JLAURX THIRD ANGLE PROJECTION 4 2019/01/28 2019/01/29 2019/01/29 IMPACT 6 PAIR PLUS 85OHM DAUGHTERCARD SIGNAL GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER DRAWING C-SIZE 2010/09/29 2010/10/19 SERIES 170540 3 DOC TYPE SD-170540-0002 MATERIAL NUMBER DOC PART PSD 001 C2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 REVISION 1 OF 2 1 A 12 H 11 9 8 # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" 170540-3*08 8 48 22.80 13.30 170540-3*10 10 60 26.60 17.10 170540-3*16 16 96 38.00 28.50 170540-3*38 8 48 22.80 13.30 170540-3*20 10 60 26.60 17.10 170540-3*24 14 84 34.20 24.70 170540-3*26 16 96 38.00 28.50 MATERIAL NUMBER G 10 7 5 6 4 3 2 1 170540-3*** PTH ⌀ MODULE & TAIL PLATING TYPE 0.46 ±0.05 # OF COLUMNS 3 = LEFT GUIDED, LEAD-FREE 08 = 8 COL 0.46 PTH 10 = 10 COL 0.46 PTH 16 = 16 COL 0.46 PTH 20 = 10 COL 0.39 PTH 24 = 14 COL 0.39 PTH 26 = 16 COL 0.39 PTH 38 = 08 COL 0.39 PTH POLARIZATION KEY ORIENTATION 0 = NO KEY 1=A 5=E 2=B 6=F 3=C 7=G 4=D 8=H 0.39 ±0.05 H G F F E E D D C C B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2019/01/29 10 02:36:16 C 9 8 7 6 SCALE mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 DOCUMENT STATUS 12 DIMENSION UNITS ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION = 0 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 CURRENT REV DESC: EC NO: DRWN: CHK'D: APPR: INITIAL DRWN: APPR: 611164 DMORGAN TELO TELO REVISION: JLAURX JLAURX THIRD ANGLE PROJECTION 4 2019/01/28 2019/01/29 2019/01/29 IMPACT 6 PAIR PLUS 85OHM DAUGHTERCARD SIGNAL GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER DRAWING C-SIZE 2010/09/29 2010/10/19 SERIES 170540 3 DOC TYPE SD-170540-0002 MATERIAL NUMBER DOC PART PSD 001 C2 SHEET NUMBER CUSTOMER GENERAL MARKET 2 REVISION 2 OF 2 1 A