1710705026

12 11 10 9 7 8 5 6 4 3 2 1 1.2 (TAIL LENGTH) 1.60 MIN BOARD THICKNESS SEE NOTE 11 H 3.80 H 9.2 7.6 SEE NOTE 10 SEE NOTE 12 6.75 8.70 G G PIN A1 11.4 F F 8.66 B BACKPLANE (REF) �2.1� BP ROW A A E 5.10 SIGNAL HOLES REF 0.84 GROUND HOLE REF SEE NOTE 9 �10.9� E ROW F ROW E ROW D ROW C ROW B ROW A D 5.00 B A NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN MIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE MATTE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPEC PS-170540-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS. 5. PRODUCT IS PACKAGED PER PK-70873-592. 6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC SPEC PS-45499-002. 7. REFER TO MOLEX SALES DRAWING SD-171065-0003 OR RSD-171062-XXXX FOR THE MATING HEADERS. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR THE ANTIPAD AND ROUTING RECOMMENDATIONS. 9. GROUND PATHS ARE NOT DISCRETE CIRCUITS WITHIN CONNECTOR DUE TO PRESENCE OF PLUS CLIP. 10. PART NUMBER 171070-5020 SHOWN ON DRAWING. KEYING FEATURES WILL CHANGE WITH COLUMN SIZE. 11. WHEN USING MOLEX SUPPLIED # 2-32 SCREW 73726-4000 (4.31mm±0.38 THREADABLE SCREW LENGTH), MIN. BOARD THICKNESS IS 1.6mm FOR SCREW/BOSS FUNCTIONALITY. 12. MARKING: LOCATED APPROXIMATELY AS SHOWN. PART NUMBER AND DATE CODE. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/03/01 10 8 8.70 D 0.35 1.35 5X ⌖ ⌀ 0.10 OFFSET BETWEEN DC AND BP HOLE COLUMNS 14.00 (FULLY MATED) ⌀3.80 UNPLATED HOLE C BACKPLANE (REF) BP PIN A1 DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:25:47 9 6.75 1.70 MAX PIN A1 ⌖ ⌀ 0.10 ⌀ PTH (SEE CHART) (6 HOLES PER COLUMN) SEE NOTE 3. C KEEP-OUT ZONE 1.90 7 6 5 EC NO: 612533 DRWN: JKUMARSARAFS CHK'D: TMARRI APPR: BOKOK INITIAL REVISION: DRWN: KBENES APPR: KBENES THIRD ANGLE PROJECTION IMPACT 85 OHM DC 2018/11/21 2 PAIR SIGNAL MODULE GUIDE RIGHT SALES DWG 2019/02/21 2019/03/01 2012/02/07 2012/02/07 DRAWING SERIES C-SIZE 171070 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 3 SD-171070-0004 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A2 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 10 9 7 8 6 5 4 3 2 1 H H MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" MAX DIM "B" 171070-5010 10 20 26.60 17.10 171070-5016 16 32 38.00 28.50 171070-5020 10 20 26.60 17.10 171070-5026 16 32 38.00 28.50 G PTH ⌀ 171070- 0 * ** 0.46 ± 0.05 0.39 ± 0.05 # OF COLUMNS 10 = 10 COL 0.46 PTH 16 = 16 COL 0.46 PTH 20 = 10 COL 0.39 PTH 26 = 16 COL 0.39 PTH MODULE & TAIL PLATING TYPE 5 = RIGHT GUIDED LEAD-FREE G F F E E D D C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/03/01 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:25:47 9 8 7 6 5 EC NO: 612533 DRWN: JKUMARSARAFS CHK'D: TMARRI APPR: BOKOK INITIAL REVISION: DRWN: KBENES APPR: KBENES THIRD ANGLE PROJECTION IMPACT 85 OHM DC 2018/11/21 2 PAIR SIGNAL MODULE GUIDE RIGHT SALES DWG 2019/02/21 2019/03/01 2012/02/07 2012/02/07 DRAWING SERIES C-SIZE 171070 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 3 SD-171070-0004 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A2 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A