1712244001

12 11 10 H 9 8 7 YYDDDX DATE CODE, SEE NOTE8 G F 0.6 DIM X 4 3 2 1 NOTES: 1. MATERIAL: CAGE: NICKEL SILVER CONNECTOR HOUSING: GLASS FILLED THERMOPLASTIC, UL: 94V-0, COLOR: BLACK TERMINALS: HIGH PERFORMANCE COPPER ALLOY FRONT SHIELD WALL: COPPER ALLOY 2. FINISH TERMINALS: CONTACT AREA: 0.76 µm MIN. HARD GOLD OVER 3.8 µm MIN. NICKEL. COMPLIANT TAIL: 0.7-1.5 µm MATTE TIN OVER: 0.7-1.5 µm NICKEL FRONT SHIELD WALL: 0.7-1.5 µm NICKEL OVERALL 3. 2X4 CONFIGURATION SHOWN FOR REFERENCE, SEE CHART FOR AVAILABLE OPTIONS 4. REFER TO PS-170071-0001 FOR ALL ELECTRICAL, MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS. 5. REFER TO AS-170071-0001 FOR CONNECTOR MOUNTING AND REWORK INFORMATION. 6. REFER TO AS-170071-0002 FOR PCB ROUTING RECOMMENDATIONS. 7. ALL VISIBLE EXTERIOR SURFACES TO BE CLASS "B" (BOTTOM OF CONNECTOR IS CLASS "C") CAGE SURFACES TO CONFORM TO THE MOLEX COSMETIC DOC PS-45499-002. 8. DATE CODE FORMAT: YYDDDX YY: LAST TWO DIGITS OF THE YEAR DDD: DAY OF THE YEAR X: MOLEX INTERNAL CONTROL DIM Y REF E 5 6 +0.25 -0.10 G F +0.3 (2X) -0.1 E 63.25 REF +0.3 0.7 (2X) -0.1 14.00 ±0.10 TYP D H 13.9 9.00 ±0.10 TYP D 25.8 REF 25.2 ±0.2 1.5 SIGNAL TAILS (SHORT) 9.00 ±0.10 TYP C C 11.5 REF 3.0 LOCATING PEGS 1.7 SIGNAL TAILS (LONG) 2.6 CAGE TAILS B B A SYMBOLS PORT SIZE PART NUMBER DIM X DIM Y 2X1 2X2 2X4 2X6 2X8 2X12 1712241001 1712242001 1712244001 1712246001 1712248001 1712241201 14.75 29.00 57.50 86.00 114.50 171.50 15.10 29.35 57.85 86.35 114.85 171.85 = 0 = 0 = 0 DOCUMENT STATUS 12 P1 RELEASE DATE 11 2019/09/17 10 C 9 8 7 6 MM 2:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 08:00:47 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 623914 DRWN: CWANG67 CHK'D: CWANG67 APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: MBANAKIS THIRD ANGLE PROJECTION 2019/09/09 2019/09/11 2019/09/17 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/01/10 2012/01/13 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER WITHOUT LIGHT PIPES 3 SD-171224-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 F1 SHEET NUMBER GENERAL MARKET 1 OF 5 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H G G T11 T20 F F T1 T10 E E L10 L1 L20 L11 D D C C B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2019/09/17 10 08:00:47 C 9 8 7 6 MM 2:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 623914 DRWN: CWANG67 CHK'D: CWANG67 APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: MBANAKIS THIRD ANGLE PROJECTION 2019/09/09 2019/09/11 2019/09/17 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/01/10 2012/01/13 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER WITHOUT LIGHT PIPES 3 SD-171224-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 F1 SHEET NUMBER GENERAL MARKET 2 OF 5 1 A 12 11 10 9 8 7 5 6 4 3 2 CONNECTOR OUTLINE, SEE NOTE1. H 3.50 1 ⌀ 0.37 ±0.05 FINISH HOLE ⌖ ⌀0.05Ⓜ B C 7.20 3.50 H 3.95 0.80 3.95 SEE DETAIL A SEE DETAIL B 0.70 TRACE KEEP-OUT AREAS, SEE NOTE2 9.00 3.50 (3X) G 13.28 0.70 6.00 G 3.00 12.0 1.72 C 1.50 6.29 ⌀ 1.60 ±0.03 1.30 0.50 F 8.00 (4X) DRILL HOLE ⌖ ⌀0.05Ⓜ B C 9.80 F DETAIL A SCALE 5:1 3.00 (4X) TRACE KEEP-OUT AREAS, SEE NOTE2 E E PIN MAP 4.00 (4X) T13 T19 T16 T20 T14 T17 T11 T15 T12 T18 FRONT EDGE OF BOARD 1.50 (4X) 14.25 T1 ⌀ 0.56 ±0.05 T4 L9 L10 T6 DIM "W" T9 L3 L6 L4 L7 L8 D T10 T7 T3 FINISH HOLE ⌖ ⌀0.10Ⓜ B C T8 T5 T2 D L1 L5 L2 L18 L12 L15 L20 L17 L14 L11 L19 L16 L13 C C DETAIL B SCALE 6:1 HOLE CHART PORT DIM "W" CONNECTOR SHIELD LOCATION SIZE (⌀0.37) (⌀0.56) ( ⌀ 1.60) 14.25 28.50 57.00 85.50 114.00 40 80 160 240 320 24 39 69 99 129 2X12 171.00 480 189 2X1 2X2 2X4 2X6 2X8 B 2 4 8 B 12 16 24 SYMBOLS = 0 = 0 NOTES: A = 0 1. THE ENTIRE AREA UNDER THE CONNECTOR IS A KEEP OUT ZONE FOR COMPONENTS AND TRACES, TOP LAYER ONLY, EXCEPT FOR CHASSIS GROUND. 2. CROSS-HATCHED AREAS INDICATE PLACES WHERE THE PLASTIC HOUSING AND METAL CAGE MAY CONTACT PCB SURFACE. THESE AREAS ARE KEEP OUT ZONES. CROSS-HATCHED AREA UNDER THE CONNECTOR ARE TRACE AND VIA KEEP OUT AREAS FOR THE TOP LAYER. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/09/17 10 9 8 7 6 MM 3:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 C SCALE ANGULAR TOL = 0 08:00:47 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 623914 DRWN: CWANG67 CHK'D: CWANG67 APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: MBANAKIS THIRD ANGLE PROJECTION 2019/09/09 2019/09/11 2019/09/17 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/01/10 2012/01/13 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER WITHOUT LIGHT PIPES 3 SD-171224-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 F1 SHEET NUMBER GENERAL MARKET 3 OF 5 1 A 12 11 10 9 8 7 5 6 DIM E ±0.10 H 4 3 2 1 3.5 BEZEL R 0.5 (4X) Z H CONNECTOR OUTLINE FRONT EDGE OF CONNECTOR G BEZEL CUT-OUT 26.00 ±0.10 Z F PCB 0.00 ±0.10 BEZEL OPENING FLUSH WITH TOP SIDE OF PCB BEZEL CUT-OUT DETAIL BEZEL THICKNESS 0.8-2.6 G SECTION Z-Z F E E 1.75 SEE NOTE DIM "E" 15.50 29.75 58.25 86.75 115.25 172.25 PORT SIZE D 2X1 2X2 2X4 2X6 2X8 2X12 D C C BEZEL CUT-OUT FOR CONNECTOR STACKING B B SYMBOLS = 0 = 0 = 0 NOTE: A FOR SIDE BY SIDE STACKING OF CONNECTORS. A BASIC DIMENSION OF 3.0mm BETWEEN CONNECTOR MOUNTING PATTERNS IS THE RECOMMENDED MINIMUM SPACING. DOCUMENT STATUS 12 P1 RELEASE DATE 11 2019/09/17 10 C 9 8 7 6 MM 2:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 08:00:47 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 623914 DRWN: CWANG67 CHK'D: CWANG67 APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: MBANAKIS THIRD ANGLE PROJECTION 2019/09/09 2019/09/11 2019/09/17 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/01/10 2012/01/13 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER WITHOUT LIGHT PIPES 3 SD-171224-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 F1 SHEET NUMBER GENERAL MARKET 4 OF 5 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H DATE 2019/09/09 REV. F1 1.ADDED REVISION HISTORY. REVISION HISTORY DESCRIPTION 2.CHG DATE CODE FORMAT IN SHEET1. 3.ADDED SIGNAL PIN TAIL LENGTH FOR SHORT. 4.ADDED NOTES IN SHEET3 G G F F E E D D C C B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2019/09/17 10 08:00:47 C 9 8 7 6 mm 1:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 623914 DRWN: CWANG67 CHK'D: CWANG67 APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: MBANAKIS THIRD ANGLE PROJECTION 2019/09/09 2019/09/11 2019/09/17 ZSFP+ STACKED ASSY METAL SPRING FINGER WITHOUT LIGHT PIPES PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/01/10 2012/01/13 DRAWING SERIES SD-171224-0001 MATERIAL NUMBER CUSTOMER C-SIZE 171224 4 3 PSD 001 GENERAL MARKET 2 F1 SHEET NUMBER 5 OF 5 1 A