1712248011

12 11 10 9 7 8 6 YYDDDX DATE CODE, SEE NOTE8. G F 0.6 E 4 3 2 1 NOTES: 1. MATERIAL: CAGE: NICKEL SILVER CONNECTOR HOUSING: GLASS FILLED THERMOPLASTIC, UL: 94V-0, COLOR: BLACK LIGHT PIPES: POLYCARBONATE, 94 HB, COLOR: CLEAR TERMINALS: HIGH PERFORMANCE COPPER ALLOY FRONT SHIELD WALL: COPPER ALLOY LIGHT PIPE HOUSING: ZINC ALLOY 2. FINISH TERMINALS: CONTACT AREA: 0.76 µm MIN. HARD GOLD OVER 3.8 µm MIN. NICKEL. COMPLIANT TAIL: 0.7-1.5 µm MATTE TIN OVER: 0.7-1.5 µm NICKEL FRONT SHIELD WALL: 0.7-1.5 µm NICKEL OVERALL LIGHT PIPE HOUSING: 2.0 µm NICKEL OVER 0.7 µm COPPER 3. 2X4 CONFIGURATION SHOWN FOR REFERENCE, SEE CHART FOR AVAILABLE OPTIONS 4. REFER TO PS-170071-0001 FOR ALL ELECTRICAL, MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS. 5. REFER TO AS-170071-0001 FOR CONNECTOR MOUNTING AND REWORK INFORMATION. 6. REFER TO AS-170071-0002 FOR PCB ROUTING RECOMMENDATIONS. 7. ALL VISIBLE EXTERIOR SURFACES TO BE CLASS "B" (BOTTOM OF CONNECTOR IS CLASS "C") CAGE SURFACES TO CONFORM TO THE MOLEX COSMETIC DOC PS-45499-002. 8. DATE CODE FORMAT:YYDDDX YY: LAST TWO DIGITS OF THE YEAR DDD: DAY OF THE YEAR X: MOLEX INTERNAL CONTROL DIM Y REF H 5 +0.3 (2X) -0.1 H G F E +0.25 DIM X -0.10 63.25 REF +0.3 0.7 (2X) -0.1 14.00 ±0.10 TYP 13.9 D D 9.00 ±0.10 TYP 25.8 REF 25.2 ±0.2 1.5 SIGNAL TAILS (SHORT) 9.00 ±0.10 TYP C C 1.7 SIGNAL TAILS (LONG) 11.5 REF 3.0 LOCATING PEGS 2.6 CAGE TAILS B A B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION PORT PART NUMBER SIZE DIM X DIM Y 2X1 2X2 2X4 2X6 2X8 2X12 14.75 29.00 57.50 86.00 114.50 171.50 15.10 29.35 57.85 86.35 114.85 171.85 17122410** 17122420** 17122440** 17122460** 17122480** 17122412** DOCUMENT STATUS 12 P1 RELEASE DATE 11 2019/09/17 10 SCALE mm 2:1 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) **-DESIGNATES LIGHT PIPE CONFIGURATIONS, SEE SHEET 2 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 DIMENSION UNITS ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:55:22 9 8 7 6 5 EC NO: 623740 2019/08/22 2019/09/17 2019/09/17 DRWN: TMARRI CHK'D: RNELSON APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: JKACHLIC THIRD ANGLE PROJECTION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/08/08 2011/11/03 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER W/LP 3 SD-171224-0002 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 H1 SHEET NUMBER GENERAL MARKET 1 OF 5 1 A 12 11 10 9 8 7 6 5 4 3 2 1 H H T20 T11 T1 T10 INNER LIGHT PIPE G G OUTER LIGHT PIPE OUTER LIGHT PIPE INNER LIGHT PIPE F F L10 L1 L11 L20 E E Partial4 SCALE 6:1 D D C 4 LIGHT PIPE 171224-**11 B PART NUMBER DESCRIPTION 171224-**11 4 LIGHT PIPES 171224-**12 INNER 2 PORTS 171224-**13 171224-**14 171224-**15 INNER LIGHT PIPE 171224-**12 DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 OUTER 2 PORTS DOWN / UP OUTER 2 PORTS UP / DOWN THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2019/09/17 10 DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) 3 LIGHT PIPES RELEASE DATE 11 C 3 LIGHT PIPE UP / MIDDLE / DOWN 171224-**15 OUTER LIGHT PIPE UP / DOWN 171224-**14 B **- DESIGNATES PORT SIZE A OUTER LIGHT PIPE DOWN / UP 171224-**13 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:55:22 9 8 7 6 5 EC NO: 623740 2019/08/22 2019/09/17 2019/09/17 DRWN: TMARRI CHK'D: RNELSON APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: JKACHLIC THIRD ANGLE PROJECTION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/08/08 2011/11/03 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER W/LP 3 SD-171224-0002 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 H1 SHEET NUMBER GENERAL MARKET 2 OF 5 1 A 12 11 10 9 7 8 5 6 4 3 CONNECTOR OUTLINE, SEE NOTE1. 1.30 H ⌀ 0.37 ±0.05 FINISH HOLE ⌖ ⌀0.05Ⓜ B C 7.20 0.70 SEE DETAIL A 3.50 1 H 3.95 3.50 2 3.95 LED KEEP-IN ZONE 2.0 WIDE x 3.0 LONG LED CENTERED 0.80 0.70 TRACE KEEP-OUT AREAS, SEE NOTE2 SEE DETAIL B OUTER LIGHT PIPE 9.00 G 13.28 4.00 6.00 3.50 (3X) G 3.00 12.0 3.00 1.72 C 6.29 1.50 0.50 INNER LIGHT PIPE C 0.50 B ⌀ 1.60 ±0.03 9.80 F DRILL HOLE ⌖ ⌀0.05Ⓜ B C DETAIL A SCALE 5:1 8.00 (4X) 4.00 TYP F TRACE KEEP-OUT AREAS, SEE NOTE2. E E PIN MAP 3.00 (4X) 4.50 ±0.10 ⌀ 0.56 ±0.05 D EDGE OF BOARD 7.125 T19 T16 T13 T20 T17 T14 T11 T18 T15 T12 FINISH HOLE ⌖ ⌀0.10Ⓜ B C 1.50 T8 T5 T2 T10 T4 T7 T1 T3 T9 T6 14.25 L9 L6 L3 L4 L10 L7 L1 L8 L2 L5 DIM W L12 L15 L18 L11 L14 L17 L20 L13 L16 L19 C HOLE CHART PORT DIM "W" CONNECTOR SHIELD LOCATION SIZE (⌀0.37) (⌀0.56) ( ⌀ 1.60) 14.25 28.50 57.00 85.50 114.00 40 80 160 240 320 24 39 69 99 129 2X12 171.00 480 189 2X1 2X2 2X4 2X6 2X8 B 2 4 8 12 16 24 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DOCUMENT STATUS 12 DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) 1. THE ENTIRE AREA UNDER THE CONNECTOR IS A KEEP OUT ZONE FOR COMPONENTS AND TRACES, TOP LAYER ONLY, EXCEPT FOR CHASSIS GROUND. 2. CROSS-HATCHED AREAS INDICATE PLACES WHERE THE PLASTIC HOUSING AND METAL CAGE MAY CONTACT PCB SURFACE. THESE AREAS ARE KEEP OUT ZONES. CROSS-HATCHED AREA UNDER THE CONNECTOR ARE TRACE AND VIA KEEP OUT AREAS FOR THE TOP LAYER. FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 C DETAIL B SCALE 6:1 NOTES: A D P1 RELEASE DATE 11 2019/09/17 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:55:22 9 8 7 6 5 EC NO: 623740 2019/08/22 2019/09/17 2019/09/17 DRWN: TMARRI CHK'D: RNELSON APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: JKACHLIC THIRD ANGLE PROJECTION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/08/08 2011/11/03 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER W/LP 3 SD-171224-0002 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 H1 SHEET NUMBER GENERAL MARKET 3 OF 5 1 A 12 11 10 9 7 8 6 DIM E ±0.10 H 5 4 3 2 1 3.5 R 0.50 ±0.10 (4X) Z H BEZEL CONNECTOR OUTLINE FRONT EDGE OF CONNECTOR BEZEL CUT-OUT G 26.00 ±0.10 G 0.00 ±0.10 BEZEL OPENING FLUSH WITH TOP SIDE OF PCB Z F PCB SECTION Z-Z F BEZEL CUT-OUT DETAIL BEZEL THICKNESS 0.8-2.6 E E 1.75 SEE NOTE DIM "E" 15.50 29.75 58.25 86.75 115.25 172.25 PORT SIZE D 2X1 2X2 2X4 2X6 2X8 2X12 D C C BEZEL CUT-OUT FOR CONNECTOR STACKING B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) NOTE: A FOR SIDE BY SIDE STACKING OF CONNECTORS. A BASIC DIMENSION OF 3.0mm BETWEEN CONNECTOR MOUNTING PATTERNS IS THE RECOMMENDED MINIMUM SPACING. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/09/17 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:55:22 9 8 7 6 5 EC NO: 623740 2019/08/22 2019/09/17 2019/09/17 DRWN: TMARRI CHK'D: RNELSON APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: JKACHLIC THIRD ANGLE PROJECTION PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/08/08 2011/11/03 DRAWING SERIES C-SIZE 171224 4 ZSFP+ STACKED ASSY METAL SPRING FINGER W/LP 3 SD-171224-0002 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 H1 SHEET NUMBER GENERAL MARKET 4 OF 5 1 A 12 11 10 9 8 7 6 5 4 3 2 1 H H DATE 2019/09/09 REV. H1 REVISION HISTORY DESCRIPTION 1.ADDED REVISION HISTORY. 2.CHG DATE CODE FORMAT, SHEET1. 3.ADD LENGTH OF SIGNAL PIN FOR SHORT, SHEET1. 4.ADDED NOTES FOR PCB KEEP-OUT ZONE IN SHEET3 G G F F E E D D C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 1:1 CURRENT REV DESC: SEE REVISION HISTORY GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/09/17 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:55:22 9 8 7 6 5 EC NO: 623740 2019/08/22 2019/09/17 2019/09/17 DRWN: TMARRI CHK'D: RNELSON APPR: RNELSON INITIAL REVISION: DRWN: JKACHLIC APPR: JKACHLIC THIRD ANGLE PROJECTION ZSFP+ STACKED ASSY METAL SPRING FINGER W/LP PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/08/08 2011/11/03 DRAWING SERIES SD-171224-0002 MATERIAL NUMBER CUSTOMER C-SIZE 171224 4 3 PSD 001 GENERAL MARKET 2 H1 SHEET NUMBER 5 OF 5 1 A