1712961627

12 11 10 9 7 8 5 6 4 3 2 B 0.95 1 0.95 A H PIN A1 1.35 (ADD FOR END WALL) B H 1.35 (ADD FOR END WALL) 1.90 1.90 2.95 Z G ROW A ROW B ROW C ROW D ROW E ROW F ROW G ROW H ROW J ROW K ROW L ROW M ROW N ROW O ROW P SIGNAL HOLES REF 1.35 14X 18.90 24.8 GROUND HOLES REF +0.2 -0.5 24.8 18.90 1.35 14X F Z G F 2.95 E KEEP OUT ZONE (PIN LENGTH) P ±0.20 UNGUIDED BACKPLANE HOLE PATTERN (CONNECTOR SIDE) SEE NOTE 9 E ⌖ ⌀ 0.10 SEE PART NUMBER CHART AND PART NUMBER LOGIC (15 HOLES PER COLUMN) 11.95 TAIL LENGTH 1.4 D D NOTCH DESIGNATES ROW A 2.64 1.00 MINIMUM BOARD SECTION Z-Z C B A NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 10 µINCH MIN GOLD IN CONTACT AREA. SELECTIVE MATTE TIN (LEAD-FREE) ON PCB TAILS, NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-76060-999 FOR PERFORMANCE SPECIFICATIONS AND ADDITIONAL PCB INFORMATION. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PARTS PACKAGED PER PK-70873-7702. 6. SEE SHEETS 2 & 3 FOR PART NUMBERS AND BOARD RELATIONSHIPS. 7. MATES WITH IMPACT DC SERIES NO. 76060. 8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR ANTIPAD AND ROUTING RECOMMENDATIONS. 9. "THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMMODATE CONNECTOR INSERTION AND REPAIR ON THE PC BOARD. THIS IS REFERRED TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT THE ACTUAL PERIMETER OF THE CONNECTOR. WHEN LAYING OUT A PC BOARD FOR CONNECTORS STACKED TOGETHER, USE THE 1.9mm PROGRESSION." C B SYMBOLS = 0 = 0 = 0 DOCUMENT STATUS 12 P1 RELEASE DATE 11 2019/01/10 10 C 9 8 7 6 mm 4:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 07:24:02 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 610093 DRWN: SKRISHNAMURT CHK'D: HLGOH APPR: HLGOH INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2018/09/04 2018/10/25 2019/01/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/11/21 2011/12/02 DRAWING SERIES C-SIZE 171296 4 IMPACT 5 PAIR BACKPLANE UNGUIDED ASSEMBLY SALES DRAWING 3 SD-171296-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 B1 SHEET NUMBER GENERAL MARKET 1 OF 3 1 A 12 11 10 9 7 8 5 6 4 3 2 1 PART NUMBER CHART H MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" DIM "B" 171296-182* 8 40 17.9 13.30 171296-112* 10 50 21.7 17.10 171296-122* 12 60 25.5 20.90 171296-172* 14 70 29.3 24.70 171296-162* 16 80 33.1 28.50 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" DIM "B" 171296-118* 8 40 16.5 13.30 171296-111* 10 50 20.3 17.10 171296-121* 12 60 24.1 20.90 171296-171* 14 70 27.9 24.70 171296-161* 16 80 31.7 28.50 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" DIM "B" 171296-183* 8 40 16.5 13.30 171296-113* 10 50 20.3 17.10 171296-123* 12 60 24.1 20.90 171296-173* 14 70 27.9 24.70 171296-163* 16 80 31.7 28.50 MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIR DIM "A" DIM "B" 171296-180* 8 40 15.1 13.30 171296-110* 10 50 18.9 17.10 171296-120* 12 60 22.7 20.90 171296-170* 14 70 26.5 24.70 171296-160* 16 80 30.3 28.50 G F E D C H DUAL END WALL OPTION DUAL END WALL OPTION G LEFT END WALL OPTION LEFT END WALL OPTION F E RIGHT END WALL OPTION RIGHT END WALL OPTION D OPEN WALL OPTION OPEN WALL OPTION C B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2019/01/10 10 07:24:02 C 9 8 7 6 mm 2:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 610093 DRWN: SKRISHNAMURT CHK'D: HLGOH APPR: HLGOH INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2018/09/04 2018/10/25 2019/01/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/11/21 2011/12/02 DRAWING SERIES C-SIZE 171296 4 IMPACT 5 PAIR BACKPLANE UNGUIDED ASSEMBLY SALES DRAWING 3 SD-171296-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 B1 SHEET NUMBER GENERAL MARKET 2 OF 3 1 A 12 11 10 9 7 8 5 6 4 3 2 1 PART NUMBER LOGIC H H 171296- **** IMPACT 5 PAIR BOARD RELATIONSHIPS P=PIN LENGTH 3 = 4.50 (SHORT COMPLIANT, 0.46±0.05 PTH) 4 = 4.90 (SHORT COMPLIANT, 0.46±0.05 PTH) 5 = 5.50 (SHORT COMPLIANT, 0.46±0.05 PTH) 6 = 4.50 (MICRO COMPLIANT, 0.39±0.05 PTH) 7 = 4.90 (MICRO COMPLIANT, 0.39±0.05 PTH) 8 = 5.50 (MICRO COMPLIANT, 0.39±0.05 PTH) MODULE TYPE 1 = UNGUIDED,MATTE TIN # OF COLUMNS 1 = 10 COL 2 = 12 COL 6 = 16 COL END WALL OPTIONS 7 = 14 COL 8 = 8 COL 0 = OPEN ENDS 1 = LEFT END WALL 2 = DUAL END WALL 3 = RIGHT END WALL G DCARD PCB BP ROW A 24.8 F G F 3.0 BPLANE PCB E E DC HOLE COLUMN (COLUMN 10 REF) DCARD ROW A D D 14.0 11.95 BP ROW A DCARD PCB DCARD ROW A C BPLANE PCB C 0.35 OFFSET BETWEEN DC AND BP HOLE COLUMNS BP HOLE COLUMN (COLUMN 10 REF) B B SYMBOLS = 0 = 0 = 0 A P1 RELEASE DATE 11 2019/01/10 10 07:24:02 C 9 8 7 6 mm 2:1 = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: MIGRATED TO NX GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 610093 DRWN: SKRISHNAMURT CHK'D: HLGOH APPR: HLGOH INITIAL REVISION: DRWN: JBINGHAM APPR: JLAURX THIRD ANGLE PROJECTION 2018/09/04 2018/10/25 2019/01/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2011/11/21 2011/12/02 DRAWING SERIES C-SIZE 171296 4 IMPACT 5 PAIR BACKPLANE UNGUIDED ASSEMBLY SALES DRAWING 3 SD-171296-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 B1 SHEET NUMBER GENERAL MARKET 3 OF 3 1 A