1713201022

12 11 10 9 8 7 5 6 4 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30uIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-171320-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER PK-78888-085. 6. SEE SHEET 2 FOR HOLE PATTERN DIMENSIONS. 7. MATES WITH IMPEL BP SERIES NUMBER 171315. 8. REFER TO IMPEL PCB ROUTING GUIDE AS-171320-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 9. WHEN STACKING MODULES END TO END, THE MINIMUM COLUMN TO COLUMN HOLE SPACING IS 2.65mm. H 21.3 20.9 1.00 MIN BOARD 1.30 TAIL LENGTH 1.90 3 G 21.90 F H G F 18.40 E E 11.90 1.20 D D A BACKPLANE (REF) �1.9� 22.6 C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: ADD NEW P/N GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/09/16 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:04:34 9 8 7 6 5 EC NO: 623408 DRWN: HLGOH CHK'D: YLLIM APPR: DWLEE01 INITIAL REVISION: DRWN: JLAURX APPR: JLAURX THIRD ANGLE PROJECTION 2019/04/12 2019/08/29 2019/09/16 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/13 2012/11/05 DRAWING SERIES C-SIZE 171320 4 IMPEL DAUGHTERCARD ASSY 4 PAIR - 1.9MM PITCH UNGUIDED SALES DRAWING 3 SD-171320-0001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 A4 SHEET NUMBER 1 OF 2 1 A 12 H 11 10 9 8 MATERIAL NUMBER NUMBER OF COLUMNS NUMBER OF DIFF PAIR DIM "A" DIM "B" 171320-1036 6 24 12.15 MAX 9.50 171320-1038 8 32 15.95 MAX 13.30 171320-1020 10 40 19.75 MAX 17.10 171320-1022 12 48 23.55 MAX 20.90 171320-1024 14 56 27.35 MAX 24.70 171320-1026 16 64 31.15 MAX 28.50 7 5 6 4 3 2 1 H B 1.90 G G 1.47 SEE NOTE 9 1.18 SEE NOTE 9 KEEP-OUT ZONE F 21.90 E GND 0.00 GND 18.40 H1 G1 16.00 GND GND 13.80 F1 11.40 E1 GND GND 9.20 D1 C1 6.80 GND GND 4.60 B1 A1 2.20 GND 17.30 17.30 14.90 14.90 12.70 12.70 10.30 10.30 8.10 8.10 5.70 5.70 3.50 3.50 1.10 1.10 18.40 GND F GND 16.20 H10 G10 13.80 GND GND 11.60 F10 E10 9.20 GND GND 7.00 D10 C10 4.60 GND GND 2.40 B10 A10 0.00 GND E EVEN COLUMN DIMENSIONS PIN A1 D SIGNAL VIA GROUND VIA ACTUAL PIN NUMBERS DEPENDENT UPON CONNECTOR COLUMN SIZE BACKPLANE (REF) C ⌀ 0.36 ±0.05 (17 HOLES PER COLUMN) ODD COLUMN DIMENSIONS 1.70 MAX 14.00 (FULLY MATED) D ⌖ ⌀0.10 C BP PIN A1 DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: ADD NEW P/N GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2019/09/16 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:04:34 9 8 7 6 5 EC NO: 623408 DRWN: HLGOH CHK'D: YLLIM APPR: DWLEE01 INITIAL REVISION: DRWN: JLAURX APPR: JLAURX THIRD ANGLE PROJECTION 2019/04/12 2019/08/29 2019/09/16 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/13 2012/11/05 DRAWING SERIES C-SIZE 171320 4 IMPEL DAUGHTERCARD ASSY 4 PAIR - 1.9MM PITCH UNGUIDED SALES DRAWING 3 SD-171320-0001 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 A4 SHEET NUMBER 2 OF 2 1 A