1713203022

12 11 10 9 8 7 5 6 4 20.9 1.00 MIN BOARD 1.90 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY H 2. FINISH: 30uIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-171320-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER PK-78888-085. 6. SEE SHEET 2 FOR HOLE PATTERN DIMENSIONS. G 7. MATES WITH IMPEL BP SERIES NUMBER 171315. 8. REFER TO IMPEL PCB ROUTING GUIDE AS-171320-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 9. WHEN STACKING MODULES END TO END, THE MINIMUM COLUMN TO COLUMN HOLE SPACING IS 2.65mm. 10. WHEN USING THE SUPPLIED 2-32 THREAD FORMING SCREW (P/N 73726-0000), THE MAXIMUM RECOMMENDED BOARD F THICKNESS IS 4.4mm. 21.3 H 3 1.30 TAIL LENGTH G 21.90 18.40 F 11.90 E E 1.20 BACKPLANE (REF) �1.9� A D D 22.6 C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 28.08.2017 C 14:20:59 10 9 8 7 6 0 = 0 = 0 = 0 = 0 = 0 5 2017/06/22 2017/08/11 2017/08/28 DATE B JLAURX ± 4 PLACES 119227 NSRIVATSAHS CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: KEY SHOWN IN POSITION "A" A = REMASTERED TO NX QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES 4:1 MM ONLY = 0 (UNLESS SPECIFIED) 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± CHK'D BY DATE APPR BY DATE 4 THIRD ANGLE PROJECTION C IMPEL DAUGHTERCARD ASSY 4 PAIR - 1.9MM PITCH GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING 2014/06/06 JBINGHAM DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 2012/11/19 MATERIAL NUMBER SERIES 171320 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171320-0002 3 CUSTOMER 2 PSD 1 OF 2 001 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H NUMBER OF NUMBER OF COLUMNS DIFF PAIR MATERIAL NUMBER 171320-3*36 171320-3*38 171320-3*20 171320-3*22 171320-3*24 171320-3*26 G 24 32 40 48 56 64 6 8 10 12 14 16 DIM "A" DIM "B" 19.60 MAX 23.40 MAX 27.20 MAX 31.00 MAX 34.80 MAX 38.60 MAX 9.50 13.30 17.10 20.90 24.70 28.50 B 8.92 1.18 SEE NOTE 9 1.90 4.75 2X G ⌖ ⌀0.10 ⌀ 0.36 ±0.05 PTH (17 HOLES PER COLUMN) ⌖ ⌀0.10 ⌀ 2.45 ±0.04 UNPLATED HOLES 2X F F 171320-3*** KEEP-OUT ZONE MODULE TYPE 21.90 3 = GUIDE LEFT COLUMN SIZE 36 = 6 COLUMN 38 = 8 COLUMN 20 = 10 COLUMN 22 = 12 COLUMN 24 = 14 COLUMN 26 = 16 COLUMN KEY ORIENTATION E 0 = NO KEY 1=A 5=E 2=B 6=F 3=C 7=G 4=D 8=H 12.00 14.00 E PIN A1 1.70 MAX 14.00 (FULLY MATED) D SEE DETAIL 1 16.20 16.00 14.90 14.90 13.80 13.80 12.70 12.70 11.60 11.40 10.30 9.20 8.10 8.10 7.00 6.80 5.70 5.70 4.60 3.50 B1 A1 GND GND 0.00 3.50 2.40 2.20 1.10 1.10 0.00 ODD COLUMN DIMENSIONS A DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) C2 GND GND B2 4.60 B QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES 1:1 MM ONLY = 0 (UNLESS SPECIFIED) A2 GND EVEN COLUMN DIMENSIONS DETAIL 1 SCALE 6:1 RELEASE STATUS FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 28.08.2017 C 14:20:59 10 9 8 C BP PIN A1 E2 GND GND D2 10.30 9.20 BACKPLANE (REF) 7 6 = 0 = 0 = 0 = 0 = 0 = 0 = 0 5 DRWN BY DATE ANGULAR TOL ± 0.5 ° B JLAURX ± 4 PLACES REV B 17.30 2017/06/22 2017/08/11 2017/08/28 C1 GND GND 17.30 GND GND H2 G2 GND GND F2 REMASTERED TO NX GND GND D1 18.40 119227 NSRIVATSAHS CYLIAW DWLEE01 C 18.40 EC NO: DRWN: CHK'D: APPR: GND H1 G1 GND GND F1 E1 D SIGNAL VIA GROUND VIA 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± CHK'D BY DATE APPR BY DATE 4 THIRD ANGLE PROJECTION C IMPEL DAUGHTERCARD ASSY 4 PAIR - 1.9MM PITCH GUIDE LEFT SALES DWG PRODUCT CUSTOMER DRAWING 2014/06/06 JBINGHAM DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 2012/11/19 MATERIAL NUMBER SERIES 171320 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171320-0002 3 CUSTOMER 2 PSD 2 OF 2 001 1 A