1713355807

12 11 10 9 8 7 5 6 A ±0.25 Z KEY SHOWN IN "A" POSITION G 19.7 3 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30µIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-171320-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER PK-78888-082. 6. SEE SHEETS 2, 3, 4, AND 5 FOR HOLE PATTERN AND MATED PART DIMENSIONS. 7. MATES WITH IMPEL DC SERIES NUMBER 171990. 8. REFER TO IMPEL PCB ROUTING GUIDE AS-171320-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 9. WHEN STACKING MODULES END TO END, THE MINIMUM COLUMN TO COLUMN SPACING IS 2.65mm. 10.THE KEEP-OUT ZONE FOR THE BP HOUSING LENGTH INCLUDES THE NECESSARY SPACE REQUIRED FOR THE MATING DAUGHTERCARD HOUSING. 11.PART IS SUPPLIED WITH ONE 2-56 UNC-2A SCREW. H PIN A1 4 +0.35 -0.25 F H G F Z E E 28.6 P ±0.20 (PIN LENGTH) D 11.95 C D 6.00 ±0.20 2.10 1.3 (TAIL LENGTH) C 1.00 BOARD MINIMUM SECTION Z-Z NOTCH DESIGNATES ROW A B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/02/12 C 10:29:13 10 9 8 7 6 0 = 0 0 = 0 = 0 = 0 A1 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± DATE PRODUCT CUSTOMER DRAWING 2013/01/02 BJANOWIAK DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS IMPEL 3 PAIR BACKPLANE GUIDE RIGHT ASSEMBLY SALES DRAWING 2018/01/31 APPR BY 4 2012/12/10 DATE CHK'D BY = 5 DATE BJANOWIAK ± 4 PLACES REV RELEASE STATUS = DRWN BY ANGULAR TOL ± 0.5 ° 171621 KUCHILA CYLIAW DWLEE01 A 0 EC NO: DRWN: CHK'D: APPR: GUIDE RIGHT VERSION = MIGRATED TO NX 2018/01/31 2018/01/31 2018/02/12 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES MM 4:1 = 0 (UNLESS SPECIFIED) THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 171335 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171335-0004 3 CUSTOMER 2 PSD 1 OF 5 001 1 A 12 11 10 9 7 8 MATERIAL NUMBER NUMBER OF COLUMNS NUMBER OF DIFF PAIR DIM "A" DIM "B" DIM "C" DIM "P" PTH ⌀ 171335-58*4 8 24 22.20 13.30 1.10 4.90 0.46±0.05 171335-58*5 8 24 22.20 13.30 1.10 5.50 0.46±0.05 171335-58*7 8 24 22.20 13.30 1.20 4.90 0.36±0.05 171335-58*8 8 24 22.20 13.30 1.20 5.50 0.36±0.05 H 5 6 4 3 2 1 H 16.95 2.73 G G DC PIN A1 31.3 F F 16.20 11.95 E E BP PIN A1 C 171335- * * * * PIN LENGTH (P) 4 = 4.90 (0.46 PTH) 5 = 5.50 (0.46 PTH) 7 = 4.90 (0.36 PTH) 8 = 5.50 (0.36 PTH) MODULE TYPE 5 = GUIDE RIGHT 9 = GUIDE RIGHT END WALL D # OF COLUMNS 8 = 8 COL D MATED PART DIMENSIONS KEY ORIENTATION 0 = NO KEY 1=A 2=B 3=C 4=D 5=E 6=F 7=G 8=H C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/02/12 C 10:29:13 10 9 8 7 6 0 = 0 0 = 0 = 0 = 0 A1 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± DATE PRODUCT CUSTOMER DRAWING 2013/01/02 BJANOWIAK DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS IMPEL 3 PAIR BACKPLANE GUIDE RIGHT ASSEMBLY SALES DRAWING 2018/01/31 APPR BY 4 2012/12/10 DATE CHK'D BY = 5 DATE BJANOWIAK ± 4 PLACES 171621 KUCHILA CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: A = MIGRATED TO NX 2018/01/31 2018/01/31 2018/02/12 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES MM 4:1 = 0 (UNLESS SPECIFIED) THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 171335 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171335-0004 3 CUSTOMER 2 PSD 2 OF 5 001 1 A 12 11 10 9 7 8 MATERIAL NUMBER NUMBER OF COLUMNS NUMBER OF DIFF PAIR DIM "A" DIM "B" DIM "C" DIM "P" PTH ⌀ 171335-98*4 8 24 23.60 13.30 1.10 4.90 0.46±0.05 171335-98*5 8 24 23.60 13.30 1.10 5.50 0.46±0.05 171335-98*7 8 24 23.60 13.30 1.20 4.90 0.36±0.05 171335-98*8 8 24 23.60 13.30 1.20 5.50 0.36±0.05 H 5 6 4 3 2 1 H GUIDE RIGHT END WALL VERSION G G F F E E D D C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/02/12 C 10:29:13 10 9 8 7 6 0 = 0 0 = 0 = 0 = 0 A1 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± DATE PRODUCT CUSTOMER DRAWING 2013/01/02 BJANOWIAK DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS IMPEL 3 PAIR BACKPLANE GUIDE RIGHT ASSEMBLY SALES DRAWING 2018/01/31 APPR BY 4 2012/12/10 DATE CHK'D BY = 5 DATE BJANOWIAK ± 4 PLACES 171621 KUCHILA CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: A = MIGRATED TO NX 2018/01/31 2018/01/31 2018/02/12 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES MM 3:1 = 0 (UNLESS SPECIFIED) THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 171335 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171335-0004 3 CUSTOMER 2 PSD 3 OF 5 001 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H B G 8.63 SEE NOTE 10 1.47 SEE NOTE 9 ADD 1.40 FOR ENDWALL G ⌖ ⌀0.10 ⌀ 0.46 ±0.05 PTH 4.75 1.90 PIN A1 F GND 1.10 (13 HOLES PER COLUMN) A1 0.00 B1 1.50 1.00 GND 0.00 GND 1.10 A2 F 3.85 GND 2.60 2.60 B2 GND 3.60 3.70 GND 4.70 GND 5.80 C2 GND 7.30 7.30 D2 GND 8.30 8.40 GND 9.40 GND C1 4.70 D1 6.20 10.10 1.97 E E E1 ⌖ ⌀0.15 KEEP-OUT ZONE SEE DETAIL 1 SIGNAL VIA 10.50 E2 F1 10.90 UNPLATED SCREW HOLE ⌀ 2.45 ±0.05 D 9.40 GND 12.00 12.00 F2 GND 13.00 13.10 GND D GROUND VIA EVEN COLUMN DIMENSIONS ODD COLUMN DIMENSIONS BACKPLANE HOLE PATTERN FOR ⌀0.46 PTH (CONNECTOR SIDE) DETAIL 1 SCALE 10:1 C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/02/12 C 10:29:13 10 9 8 7 6 0 = 0 0 = 0 = 0 = 0 A1 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± DATE PRODUCT CUSTOMER DRAWING 2013/01/02 BJANOWIAK DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS IMPEL 3 PAIR BACKPLANE GUIDE RIGHT ASSEMBLY SALES DRAWING 2018/01/31 APPR BY 4 2012/12/10 DATE CHK'D BY = 5 DATE BJANOWIAK ± 4 PLACES 171621 KUCHILA CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: A = MIGRATED TO NX 2018/01/31 2018/01/31 2018/02/12 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES MM 4:1 = 0 (UNLESS SPECIFIED) THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 171335 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171335-0004 3 CUSTOMER 2 PSD 4 OF 5 001 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H B 1.47 SEE NOTE 9 G 8.63 SEE NOTE 10 ADD 1.40 FOR ENDWALL G ⌖ ⌀0.10 GND 1.20 1.10 GND (13 HOLES PER COLUMN) A1 0.00 0.10 GND 1.30 1.10 A2 GND 2.50 2.40 B2 GND 3.50 3.60 GND C1 4.70 4.60 GND D1 6.00 5.80 C2 GND 7.20 7.10 D2 GND 8.20 8.30 GND 4.75 1.90 ⌀ 0.36 ±0.05 PTH PIN A1 B1 3.95 F 10.00 19.7 E ⌖ ⌀0.15 UNPLATED SCREW HOLE ⌀ 2.45 ±0.05 D SEE DETAIL 2 E 9.30 GND E1 9.40 F1 10.70 10.50 E2 GND 11.90 11.80 F2 GND 12.90 13.00 GND D SIGNAL VIA KEEP-OUT ZONE F GROUND VIA ODD COLUMN DIMENSIONS BACKPLANE HOLE PATTERN FOR ⌀0.36 PTH (CONNECTOR SIDE) EVEN COLUMN DIMENSIONS DETAIL 2 SCALE 10:1 C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/02/12 C 10:29:13 10 9 8 7 6 0 = 0 0 = 0 = 0 = 0 A1 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± DATE PRODUCT CUSTOMER DRAWING 2013/01/02 BJANOWIAK DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS IMPEL 3 PAIR BACKPLANE GUIDE RIGHT ASSEMBLY SALES DRAWING 2018/01/31 APPR BY 4 2012/12/10 DATE CHK'D BY = 5 DATE BJANOWIAK ± 4 PLACES 171621 KUCHILA CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: A = MIGRATED TO NX 2018/01/31 2018/01/31 2018/02/12 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES MM 4:1 = 0 (UNLESS SPECIFIED) THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 171335 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171335-0004 3 CUSTOMER 2 PSD 5 OF 5 001 1 A