1714005126

12 11 10 9 7 8 5 6 4 3 2 1 30.7 30.3 TYPICAL GATE LOCATION WITH RECESS NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30uIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-171320-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER PK-78888-088. 6. SEE SHEET 2 FOR HOLE PATTERN DIMENSIONS. 7. MATES WITH IMPEL BP SERIES NUMBER 171395. 8. REFER TO IMPEL PCB ROUTING GUIDE AS-171320-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 9. WHEN STACKING MODULES END TO END, THE MINIMUM COLUMN TO COLUMN HOLE SPACING IS 2.65mm. 10. WHEN USING THE SUPPLIED 2-32 THREAD FORMING SCREW (P/N 73726-0000), THE MAXIMUM RECOMMENDED BOARD THICKNESS IS 4.4mm. 1.00 MIN BOARD H 1.30 TAIL LENGTH 1.90 G 31.10 27.60 F E H G F E 11.90 1.20 �1.9� BACKPLANE (REF) D A D 32.0 C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/06/19 C 03:31:34 10 9 8 7 6 2017/12/14 2018/06/07 2018/06/19 = 0 = 0 = 0 = 0 = 0 = 0 A4 5 DRWN BY DATE ANGULAR TOL ± 0.5 ° JLAURX ± 4 PLACES REV RELEASE STATUS 0 177599 ABN CYLIAW DWLEE01 A = EC NO: DRWN: CHK'D: APPR: KEY SHOWN IN POSITION "A" MIGRATED TO NX/ECTR QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES 4:1 = 0 (UNLESS SPECIFIED) 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± CHK'D BY DATE APPR BY DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 2012/01/19 PRODUCT CUSTOMER DRAWING 2012/11/14 THIRD ANGLE PROJECTION C IMPEL DAUGHTERCARD ASSY 6 PAIR - 1.9MM PITCH GUIDE RIGHT SALES DWG MATERIAL NUMBER SERIES 171400 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171400-0004 3 CUSTOMER 2 PSD 1 OF 2 001 1 A 12 H 11 10 9 7 8 MATERIAL NUMBER NUMBER OF COLUMNS NUMBER OF DIFF PAIR DIM "A" DIM "B" 171400-5*38 171400-5*20 171400-5*26 8 10 16 48 60 96 23.40 MAX 27.20 MAX 38.60 MAX 13.30 17.10 28.50 5 6 4 3 2 1 H B 8.63 1.90 1.47 SEE NOTE 9 4.75 2X KEEP-OUT ZONE 171400-5*** G G MODULE TYPE 5 = GUIDE RIGHT COLUMN SIZE 38 = 8 COLUMN 20 = 10 COLUMN 26 = 16 COLUMN KEY ORIENTATION 0 1 2 3 4 F = = = = = NO A B C D KEY 5=E 6=F 7=G 8=H ⌖ ⌀0.10 ⌖ ⌀0.10 ⌀ 0.36 ±0.05 PTH ⌀ 2.45 ±0.04 (25 HOLES PER COLUMN) UNPLATED HOLES 2X F 31.10 14.00 26.50 24.10 24.10 21.90 21.90 19.50 19.50 17.30 17.30 25.20 23.00 20.60 18.40 16.00 14.90 14.90 12.70 12.70 10.30 10.30 13.80 11.40 9.20 8.10 8.10 5.70 5.70 3.50 3.50 1.10 1.10 6.80 4.60 2.20 SIGNAL VIA SEE DETAIL 1 BACKPLANE (REF) DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES 1:1 = 0 (UNLESS SPECIFIED) A FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 2018/06/19 C BP PIN A1 DETAIL 1 SCALE 5:1 RELEASE STATUS D GROUND VIA EVEN COLUMN DIMENSIONS ODD COLUMN DIMENSIONS B 14.00 (FULLY MATED) PIN A1 1.70 MAX C 03:31:34 10 9 8 7 6 = 0 = 0 = 0 = 0 = 0 = 0 = 0 A4 5 DRWN BY DATE ANGULAR TOL ± 0.5 ° JLAURX ± 4 PLACES REV 0.00 16.00 E GND 25.40 M2 L2 23.00 GND GND 20.80 K2 J2 18.40 GND GND 16.20 H2 G2 13.80 GND GND 11.60 F2 E2 9.20 GND GND 7.00 D2 C2 4.60 GND GND 2.40 B2 A2 0.00 GND 2017/12/14 2018/06/07 2018/06/19 C 26.50 MIGRATED TO NX/ECTR D 27.60 GND 177599 ABN CYLIAW DWLEE01 E 27.60 EC NO: DRWN: CHK'D: APPR: GND M1 L1 GND GND K1 J1 GND GND H1 G1 GND GND F1 E1 GND GND D1 C1 GND GND B1 A1 GND GND 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± CHK'D BY DATE APPR BY DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 2012/01/19 PRODUCT CUSTOMER DRAWING 2012/11/14 THIRD ANGLE PROJECTION C IMPEL DAUGHTERCARD ASSY 6 PAIR - 1.9MM PITCH GUIDE RIGHT SALES DWG MATERIAL NUMBER SERIES 171400 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171400-0004 3 CUSTOMER 2 PSD 2 OF 2 001 1 A