1715001022

12 11 10 9 7 8 5 6 4 1.00 MIN BOARD H 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30uIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-171320-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER PK-78888-241. 6. SEE SHEET 2 FOR HOLE PATTERN DIMENSIONS. 7. MATES WITH IMPEL ORTHO BP 171495 SERIES OR ODRAM 171740 SERIES (UNGUIDED) 8. REFER TO IMPEL PCB ROUTING GUIDE AS-171500-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 31.6 2.35 3 1.30 TAIL LENGTH G 31.10 27.60 H G F F E E 11.90 1.20 28.95 MAX D BACKPLANE (REF) D �1.9� 33.3 C C ISOMETRIC VIEW A 12 COLUMNS WITH SLOTS B B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: REV UP DRAWING TO REFLECT ADDED RELIEF SLOTS ON RIGHT = 0 WAFERS. ADDED ISOMETRIC VIEW A. mm = DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/02/10 10 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± = A 0 NTS 0 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:09 9 8 7 6 5 EC NO: 693839 DRWN: JLTAN06 CHK'D: YLLIM APPR: DWLEE01 INITIAL REVISION: DRWN: JLAURX APPR: DWLEE01 THIRD ANGLE PROJECTION 2022/01/20 2022/01/28 2022/02/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/04/13 2018/06/29 SERIES DRAWING C-SIZE 171500 4 IMPEL ORTHO DAUGHTERCARD 6 PAIR X 12 COL UNGUIDED 3 SD-171500-0001 MATERIAL NUMBER PSD 001 CUSTOMER 1715001022 2 B SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 10 11 9 7 8 5 6 4 3 2 1 H H 25.85 KEEP-OUT ZONE 2.35 11X G F 31.10 E GND 0.00 D 14.00 (FULLY MATED) ⌖ ⌀0.10 1.40 ⌀ 0.36 ±0.05 27.60 GND GND 27.60 M1 26.50 L1 25.20 25.40 M12 GND 24.10 24.10 L12 GND 23.00 23.00 GND K1 21.90 21.90 GND J1 20.60 20.80 K12 GND 19.50 19.50 J12 GND 18.40 18.40 GND H1 17.30 17.30 GND G1 16.00 16.20 H12 GND 14.90 14.90 G12 GND 13.80 F1 12.70 13.80 GND E1 11.40 GND 10.30 GND 9.20 D1 8.10 C1 1.70 300X 26.50 GND F 12.70 GND 11.60 F12 10.30 E12 9.20 GND 8.10 GND 6.80 7.00 D12 GND 5.70 5.70 C12 GND 4.60 4.60 GND B1 3.50 3.50 GND A1 2.20 2.40 B12 GND 1.10 1.10 0.00 A12 GND PIN A1 SIGNAL VIA 1.70 MAX GROUND VIA PCB EDGE ODD COLUMN DIMENSIONS ISOMETRIC VIEW B 12 COLUMNS WITH SLOTS G E D EVEN COLUMN DIMENSIONS C C BACKPLANE (REF) BP PIN A1 DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SCALE SYMBOLS DIMENSION UNITS CURRENT REV DESC: REV UP DRAWING TO REFLECT ADDED RELIEF SLOTS ON RIGHT = 0 WAFERS. ADDED ISOMETRIC VIEW A. mm = DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 11 2022/02/10 10 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± = A 0 NTS 0 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:06:09 9 8 7 6 5 EC NO: 693839 DRWN: JLTAN06 CHK'D: YLLIM APPR: DWLEE01 INITIAL REVISION: DRWN: JLAURX APPR: DWLEE01 THIRD ANGLE PROJECTION 2022/01/20 2022/01/28 2022/02/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/04/13 2018/06/29 SERIES DRAWING C-SIZE 171500 4 IMPEL ORTHO DAUGHTERCARD 6 PAIR X 12 COL UNGUIDED 3 SD-171500-0001 MATERIAL NUMBER PSD 001 CUSTOMER 1715001022 2 B SHEET NUMBER GENERAL MARKET 2 OF 2 1 A