1719901038

12 11 10 9 8 7 H 5 6 4 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30uIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-171320-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER PK-78888-083. 6. SEE SHEET 2 FOR HOLE PATTERN DIMENSIONS. 7. MATES WITH IMPEL BP SERIES NUMBER 171335. 8. REFER TO IMPEL PCB ROUTING GUIDE AS-171320-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 9. WHEN STACKING MODULES END TO END, THE MINIMUM COLUMN TO COLUMN HOLE SPACING IS 2.65mm. 16.6 16.2 1.00 MIN BOARD 1.30 TAIL LENGTH G 3 1.90 17.30 F H G F 13.80 E E 11.90 1.20 A D D BACKPLANE (REF) �1.9� 17.9 C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 14.10.2017 C 14:50:03 10 9 8 7 6 0 = 0 = 0 = 0 = 0 = 0 5 2017/07/24 2017/10/03 2017/10/14 DATE A JLAURX ± 4 PLACES 120778 NSRIVATSAHS CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: A = REMASTERED TO NX QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES 4:1 MM ONLY = 0 (UNLESS SPECIFIED) 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± CHK'D BY DATE APPR BY DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 2013/04/02 PRODUCT CUSTOMER DRAWING 2013/04/03 THIRD ANGLE PROJECTION C IMPEL DAUGHTERCARD ASSY 3 PAIR - 1.9MM PITCH UNGUIDED SALES DRAWING MATERIAL NUMBER SERIES 171990 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171990-0001 3 CUSTOMER 2 PSD 1 OF 2 001 1 A 12 11 10 9 7 8 5 6 4 3 2 1 H H MATERIAL NUMBER NUMBER OF COLUMNS NUMBER OF DIFF PAIR DIM "A" DIM "B" 171990-1038 8 24 15.95 MAX 13.30 171990-1020 10 30 19.75 MAX 17.10 B 1.90 1.18 SEE NOTE 9 1.47 SEE NOTE 9 G G ⌖ ⌀0.10 KEEP-OUT ZONE ⌀ 0.36 ±0.05 PTH (13 HOLES PER COLUMN) F 17.30 GND 0.00 E GND F1 E1 GND GND D1 C1 GND GND B1 A1 GND 13.80 11.40 9.20 6.80 4.60 2.20 12.70 12.70 10.30 10.30 8.10 8.10 5.70 5.70 3.50 3.50 1.10 1.10 13.80 11.60 9.20 7.00 4.60 2.40 0.00 EVEN COLUMN DIMENSIONS ODD COLUMN DIMENSIONS 1.70 MAX PIN A1 GND GND F8 E8 GND GND D8 C8 GND GND B8 A8 GND F E SIGNAL VIA 14.00 (FULLY MATED) GROUND VIA D D ACTUAL PIN NUMBERS DEPENDENT UPON CONNECTOR COLUMN SIZE BACKPLANE (REF) BP PIN A1 DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) C C B B FORMAT: master-tb-prod-C REVISION: G DATE: 2015/02/06 12 P1 RELEASE DATE 11 14.10.2017 C 14:50:03 10 9 8 7 6 0 = 0 = 0 = 0 = 0 = 0 5 2017/07/24 2017/10/03 2017/10/14 DATE A JLAURX ± 4 PLACES 120778 NSRIVATSAHS CYLIAW DWLEE01 = DRWN BY ANGULAR TOL ± 0.5 ° REV RELEASE STATUS 0 EC NO: DRWN: CHK'D: APPR: A = REMASTERED TO NX QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS GENERAL TOLERANCES 4:1 MM ONLY = 0 (UNLESS SPECIFIED) 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± CHK'D BY DATE APPR BY DATE JLAURX DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 2013/04/02 PRODUCT CUSTOMER DRAWING 2013/04/03 THIRD ANGLE PROJECTION C IMPEL DAUGHTERCARD ASSY 3 PAIR - 1.9MM PITCH UNGUIDED SALES DRAWING MATERIAL NUMBER SERIES 171990 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-171990-0001 3 CUSTOMER 2 PSD 2 OF 2 001 1 A