1732101122

12 11 10 9 7 8 5 6 4 30.3 1.00 MIN BOARD 1.30 TAIL LENGTH 1.90 2 1 NOTES: 1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP) GLASS-FILLED, UL94V-0 TERMINALS - HIGH PERFORMANCE COPPER ALLOY 2. FINISH: 30uIN GOLD IN CONTACT AREA. SELECTIVE TIN ON PCB TAILS. NICKEL OVERALL. 3. REFER TO MOLEX PRODUCT SPECIFICATION PS-172740-999 FOR PERFORMANCE SPECIFICATIONS. 4. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF MOLEX COSMETIC SPEC PS-45499-002. 5. PRODUCT WILL BE PACKAGED PER 1732100002-PK. 6. SEE SHEET 2 FOR HOLE PATTERN DIMENSIONS. 7. MATES WITH IMPEL BP SERIES NUMBER 171395. 8. REFER TO IMPEL PCB ROUTING GUIDE AS-172730-990 FOR ANTIPAD, ROUTING RECOMMENDATIONS, AND ADDITIONAL PCB INFORMATION. 9. WHEN STACKING MODULES END TO END, THE MINIMUM COLUMN TO COLUMN HOLE SPACING IS 2.65mm. 30.7 H 3 G 31.10 H G 27.60 F F E E 11.90 D D 1.20 A BACKPLANE (REF) 32.0 C C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: CHANGE PK SPEC NUMBER GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 11 2020/04/09 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 00:10:55 9 8 7 6 5 EC NO: 633980 DRWN: HLGOH CHK'D: JLTAN06 APPR: DWLEE01 INITIAL REVISION: DRWN: TPREMO APPR: TPREMO THIRD ANGLE PROJECTION 2020/03/13 2020/03/27 2020/04/09 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/03/30 2015/04/21 DRAWING SERIES C-SIZE 173210 4 IMPEL PLUS DAUGHTERCARD 6 PAIR - 1.9MM PITCH UNGUIDED SALES DRAWING 3 SD-173210-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A2 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 MATERIAL NUMBER 10 NUMBER OF NUMBER OF COLUMNS DIFF PAIR 9 DIM 'A' 8 7 5 6 4 3 2 1 DIM 'B' H H 173210-1138 173210-1122 173210-1126 8 12 16 48 72 96 15.95 MAX 13.30 23.55 MAX 20.90 31.15 MAX 28.50 B 1.47 SEE NOTE 9 173210-11** 1.18 SEE NOTE 9 1.90 KEEP OUT ZONE ⌖ ⌀0.10 COLUMN SIZE 20 = 10 COLUMN 22 = 12 COLUMN 26 = 16 COLUMN 38 = 8 COLUMN G G ⌀ 0.36 ±0.05 PTH (12 GND HOLES PER COLUMN) ⌖ ⌀0.10 ⌀ 0.31 ±0.05 PTH (12 SIGNAL HOLES PER COLUMN) F F 31.10 MIN E D C B GND 26.50 26.50 GND M1 25.40 25.40 GND L1 24.10 24.30 M2 GND 23.00 23.00 L2 GND 21.90 21.90 GND K1 20.80 20.80 GND J1 19.50 19.70 K2 GND 18.40 18.40 J2 GND 17.30 17.30 GND H1 16.20 16.20 GND G1 14.90 15.10 H2 GND 13.80 13.80 G2 GND 12.70 12.70 GND F1 11.60 11.60 GND E1 10.30 10.50 F2 GND 9.20 9.20 E2 GND 8.10 8.10 GND D1 7.00 7.00 GND C1 5.70 5.90 D2 GND 4.60 4.60 C2 GND 3.50 3.50 GND B1 2.40 2.40 GND A1 1.10 1.30 B2 GND 0.00 0.00 A2 GND 1.10 1.10 GND ODD COLUMN DIMENSIONS A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2018/01/18 P1 DETAIL A SCALE 8:1 RELEASE DATE 11 2020/04/09 10 E 1.70 MAX GROUND VIA PIN A1 14.00 (FULLY MATED) ACTUAL PIN NUMBER DEPENDENT UPON CONNECTOR COLUMN SIZE SEE DETAIL A SIGNAL VIA D BACKPLANE (REF) BP PIN A1 C DAUGHTERCARD HOLE PATTERN (CONNECTOR SIDE) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: CHANGE PK SPEC NUMBER GENERAL TOLERANCES (UNLESS SPECIFIED) EVEN COLUMN DIMENSIONS ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 0.5 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 00:10:55 9 8 7 6 5 EC NO: 633980 DRWN: HLGOH CHK'D: JLTAN06 APPR: DWLEE01 INITIAL REVISION: DRWN: TPREMO APPR: TPREMO THIRD ANGLE PROJECTION 2020/03/13 2020/03/27 2020/04/09 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2015/03/30 2015/04/21 DRAWING SERIES C-SIZE 173210 4 IMPEL PLUS DAUGHTERCARD 6 PAIR - 1.9MM PITCH UNGUIDED SALES DRAWING 3 SD-173210-0001 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 A2 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A