1733590001

12 11 10 9 7 8 H 5 6 4 3 2 1 H MATERIAL NUMBER 1733590001 SHOWN +0.05 -0.20 10.20 TAKEN AT CENTER 10.20 +0.05 -0.10 TAKEN AT ENDS 5.50 ±0.10 KEY LENGTH 54.33 ±0.25 G G 4.50 ±0.10 11.70 3.60 ±0.10 17.06 ±0.13 KEY LOCATION 2.08 TYP SECTION Z-Z 5.50 REF 29.36 30.06 F F 54.33 +0.05 -0.10 23.56 ±0.10 27.66 8.00 2.50 REF 1.00 ±0.05 KEY Z E 1.10 ±0.13 KEY 11.90 11.63 Z 1.15 34.07 2.25 2.56 16.80 B 15.60 20.25 D NOTES: 1. MATERIALS: WAFER HOUSING: HIGH TEMPERATURE THERMOPLASTIC GLASS-FILLED, UL 94V-0; DIE CAST HOUSING: NICKEL PLATED DIE CAST ALLOY; COVER: STAINLESS STEEL ALLOY; EMI GASKET: CONDUCTIVE POLYMER; EMI FINGERS: NICKEL PLATED COPPER ALLOY; 2. FINISHES: PLATING: CONTACT AREA: 0.76µm MIN GOLD OVER 2.54µm MIN NICKEL; COMPLIANT TAIL AREA: 0.76-3.00µm TIN OVER 1.27µm MIN NICKEL; 3. PRODUCT SPECIFICATION: PS-173359-0001; 4. PACKAGING SPECIFICATION: PK-170834-0001; 5. MATES WITH: MOLEX CABLE SERIES 200433; 6. MOUNTING HARDWARE REQUIRED: M2x0.4 CAP SCREWS (3); LENGTH: PCB THICKNESS + 3.0 MIN (6.0 MM MAX); 7. APPLICATION SPECIFICATION: AS-173359-0002; 8. ROUTING GUIDELINE: AS-173359-0001. 14.19 REF 14.20 28.96 ±0.10 13.00 11.80 EMI FINGERS (SEE SHEET 2) 10.40 9.20 EMI GASKET (SEE SHEET 2) C 7.60 6.40 5.00 3.80 2.60 E D C 1.20 B B A SYMBOLS = 0 = 0 = 0 A 33.71 ±0.25 DOCUMENT STATUS 12 P1 RELEASE DATE 11 2020/10/28 10 C 9 8 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: mm ± = 0 04:29:08 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2017/10/06 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 647299 DRWN: TTAO03 CHK'D: WZHAO21 APPR: WZHAO21 INITIAL REVISION: DRWN: MHANUMAPPARE APPR: SMILLER THIRD ANGLE PROJECTION 2020/09/02 2020/10/28 2020/10/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/29 2017/02/14 DRAWING SERIES C-SIZE 173359 4 ZCD 90 OHM 16X STYLE 1 ASSEMBLY 3 SD-173359-0001 MATERIAL NUMBER PSD 000 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 1 OF 5 1 A 12 11 10 9 8 7 5 6 4 3 2 1 H H G G F F 1733590001 SHOWN WITH EMI FINGERS AND EMI GASKET 1733590002 SHOWN WITHOUT EMI FINGERS AND GASKET E E D D C C 1733590004 SHOWN WITHOUT EMI FINGERS AND WITH EMI GASKET B B SYMBOLS = 0 = 0 = 0 MATERIAL NUMBER WITH EMI FINGERS WITH EMI GASKET 1733590001 1733590002 1733590004 A YES NO NO YES NO YES DOCUMENT STATUS 12 P1 RELEASE DATE 11 2020/10/28 10 C 9 8 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: mm ± = 0 04:29:08 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2017/10/06 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 647299 DRWN: TTAO03 CHK'D: WZHAO21 APPR: WZHAO21 INITIAL REVISION: DRWN: MHANUMAPPARE APPR: SMILLER THIRD ANGLE PROJECTION 2020/09/02 2020/10/28 2020/10/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/29 2017/02/14 DRAWING SERIES C-SIZE 173359 4 ZCD 90 OHM 16X STYLE 1 ASSEMBLY 3 SD-173359-0001 MATERIAL NUMBER PSD 000 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 2 OF 5 1 A 12 11 10 9 7 8 5 6 4 0.99 0.40 ⌀ 0.74 2.81 0.15 1.33 G ⌀ 0.37 REF 0.85 Partial 2 SCALE 4:1 0.90 2 1 NOTES: 1. GROUNDS G1-G30 ARE ALL COMMON; GROUNDS G31-G60 ARE ALL COMMON; 2. CROSS-HATCHED AREA TO BE CONDUCTIVE ON THE PCB; 3. RECOMMENDED DRILL SIZE FOR 0.37⌀ FINISHED PTH IS 0.457mm⌀ (.018in⌀(#77. DRILL)); 4. RECOMMENDED ANNULAR RING AROUND 0.37⌀ FINISHED PTH IS 0.73⌀; 5. KEEP OUT AREA EXEPTION: WHEN ADJACENT CONNECTOR IS PRESENT IT WILL INTERLEAVE SHOWN KEEP OUT AREA). ABOVE AND BELOW SIGNAL LAYERS H 3 H G 30.06 1.40 KEEP OUT AREA (SEE NOTE 5) 26.50 15.45 ⌀ 0.37 ±0.05 G51 G60 D1X D10X D1Y D10Y G41 G50 C1X C10X C1Y C10Y G31 G40 TYP ⌖ ⌀0.10Ⓛ X Y F F 1.50 13.00 E D G21 G30 B1X B10X 1.20 1.40 7.60 ⌀ 2.20 ±0.05 16.80 9.20 E 3.80 PTH TYP (5) ⌖ ⌀0.10Ⓛ X Y 5.01 B1Y B10Y G11 G20 A1X A2X A3X A4X A5X A6X A7X A8X A9X A10X A1Y A2Y A3Y A4Y A5Y A6Y A7Y A8Y A9Y A10Y G1 G2 G3 G4 G5 G6 G7 G8 Y 13.01 D 17.01 23.85 G10 G9 C C Partial 1 SCALE 8:1 2.25 1.125 TOP AND BOTTOM EMI LAYER AND ALL OTHER LAYERS WITHIN BOARD 3.99 X 20.25 28.96 4.99 B PCB THICKNESS: 1.57mm MIN. 30.96 R 0.19 SYMBOLS = 0 = 0 3.65 = 0 0.15 1.75 A R 0.37 0.15 Partial 3 SCALE 4:1 2.10 DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: H DATE: 2017/10/06 P1 RELEASE DATE 11 2020/10/28 10 04:29:08 C 9 8 7 6 SCALE GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: mm ± = 0 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL = 0 RECOMMENDED PCB LAYOUT COMPONENT SIDE SHOWN 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 647299 DRWN: TTAO03 CHK'D: WZHAO21 APPR: WZHAO21 INITIAL REVISION: DRWN: MHANUMAPPARE APPR: SMILLER THIRD ANGLE PROJECTION 2020/09/02 2020/10/28 2020/10/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/29 2017/02/14 DRAWING SERIES C-SIZE 173359 4 ZCD 90 OHM 16X STYLE 1 ASSEMBLY 3 SD-173359-0001 MATERIAL NUMBER PSD 000 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 3 OF 5 1 A 12 11 10 9 7 8 5 6 4 3 2 1 KEEP OUT AREAS H H 1.00 3.58 1.25 TYP 1.00 TYP 2.74 REF 1.30 G G 45° 1.50 0.77 DETAIL A 45° DETAIL B 1.20 F F 1.33 DETAIL A SCALE 8:1 44.10 E E 29.06 TYP 22.47 TYP 1.00 1.73 25.76 18.95 27.06 17.15 2.60 D D 9.15 5.15 C DETAIL C 26.50 1.30 27.50 1.33 3.10 45° 1.87 C 30.06 R 0.50 (2X) 45° 3.43 B B DETAIL B SCALE 8:1 SYMBOLS = 0 DETAIL C SCALE 8:1 (3 PLACES) = 0 = 0 A P1 RELEASE DATE 11 2020/10/28 10 04:29:08 C 9 8 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: mm ± = 0 DOCUMENT STATUS 12 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2017/10/06 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 647299 DRWN: TTAO03 CHK'D: WZHAO21 APPR: WZHAO21 INITIAL REVISION: DRWN: MHANUMAPPARE APPR: SMILLER THIRD ANGLE PROJECTION 2020/09/02 2020/10/28 2020/10/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/29 2017/02/14 DRAWING SERIES C-SIZE 173359 4 ZCD 90 OHM 16X STYLE 1 ASSEMBLY 3 SD-173359-0001 MATERIAL NUMBER PSD 000 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 4 OF 5 1 A 12 11 10 9 7 8 5 6 4 3 2 1 H H PANEL MOUNT CONFIGURATION BEZEL 29.62 ±0.05 R 1.00 MAX G G 12.00 ±0.05 F F E E PCB BEZEL CUT-OUT (NOT SUPPLIED) EMI GASKET BEZEL 27.67 AT RECOMMENDED COMPRESSION BEZEL D D CONNECTOR ASSEMBLY PCB C C 0.15 ±0.05 PCB ASSEMBLIED VIEW B B SYMBOLS = 0 = 0 = 0 A NOTE: 1. MINIMUM PITCH BETWEEN TWO ADJACENT CONNECTORS IS 34mm; 2. BEZEL THICKNESS = 0.80 TO 2.4 mm. DOCUMENT STATUS 12 P1 RELEASE DATE 11 2020/10/28 10 C 9 8 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± = 0 CURRENT REV DESC: mm ± = 0 04:29:08 SCALE ANGULAR TOL = 0 FORMAT: master-tb-prod-C REVISION: H DATE: 2017/10/06 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS 1 PLACE ± 0 PLACES ± 0.5 ° 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 EC NO: 647299 DRWN: TTAO03 CHK'D: WZHAO21 APPR: WZHAO21 INITIAL REVISION: DRWN: MHANUMAPPARE APPR: SMILLER THIRD ANGLE PROJECTION 2020/09/02 2020/10/28 2020/10/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/29 2017/02/14 DRAWING SERIES C-SIZE 173359 4 ZCD 90 OHM 16X STYLE 1 ASSEMBLY 3 SD-173359-0001 MATERIAL NUMBER PSD 000 CUSTOMER GENERAL MARKET SEE TABLE 2 B SHEET NUMBER 5 OF 5 1 A