MX150L ASSEMBLY INSTRUCTIONS
CONNECTOR PLUG ASSEMBLY
TERMINAL INSERTION
1. Begin assembly of the crimped male terminals into the plug housing by making sure the
Terminal Position Assurance feature (TPA) is in the pre-locked position (See Figure 1).
• Since the TPA is recessed in housing, the most accurate way to determine if it is in
pre-lock position is to measure. In pre-locked position, the dimension between
plug housing face and TPA is approximately 0.500” (12,7mm).
• If it is not in pre-locked position, insert the tips of a pair of needle nose pliers into
the two “D” shaped holes in the center of the TPA. Carefully, pull gently on the
TPA until it starts moving. Pull to first stop. CAUTION: DO NOT PULL TPA
COMPLETELY OUT OF HOUSING. THIS MAY BREAK RETENTION FEATURES AND
RESULT IN REDUCED TPA RETENTION IN HOUSING. You are now ready to insert
terminals and/or circuit plugs.
TPA
0.500”
(12.7mm)
Figure 1: TPA in Pre-Locked Position
2. The terminal must be positioned correctly when inserted into the housing to assure proper
latching and retention. Orient the key on the back of the male terminal with the keyway on
the rear of the housing (See Figure 2). Insert the terminal into the housing until it clicks
and a slight pull back on the wire is met with resistance from terminal retention feature.
Keyway in Wire Entry
Keyway on Terminal
Figure 2: Terminal Orientation
REVISION:
B
ECR/ECN INFORMATION:
EC No: IPG2013-0274
DATE: 2012 / 08 / 22
DOCUMENT NUMBER:
AS-19417-001
TITLE:
ASSEMBLY INSTRUCTIONS FOR
MX150L SEALED CONNECTOR
SYSTEM
SHEET No.
1 of 5
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
WLEUNG
DTITUS
DTITUS
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
MX150L ASSEMBLY INSTRUCTIONS
3. Repeat Step 2 until all terminals are inserted into the housing. If a terminal is inadvertently
assembled into the wrong position, use service tool to remove.
4. If using a circuit plug to seal an unused circuit, apply the same procedure as terminal
insertion above. Insert the circuit plug until it clicks once and a slight pull back on the
circuit plug is met with resistance from terminal retention feature.
• DO NOT continue to push the circuit plug after the audible click. The circuit plug
should rest on the first stop in the connector plug housing.
• In its final position, the dimension between the plug housing and the circuit plug is
approximately 0.285” (7,24mm) (See Figure 3 & Figure 4).
0.285”
(7.24mm)
Keyway in Wire Entry
First Stop
Keyway on Circuit Plug
Figure 4: Circuit Plug in Final Position
Figure 3: Circuit Plug Orientation
5. When all terminals and/or circuit plugs are in their proper location, push down on TPA
until it clicks into place and is now approximately 0.700”(17.8mm) from mating edge of
outer housing (See Figure 5).
TPA
0.700”
(17.8mm)0.
Figure 5: TPA in Locked Position
REVISION:
B
ECR/ECN INFORMATION:
EC No: IPG2013-0274
DATE: 2012 / 08 / 22
DOCUMENT NUMBER:
AS-19417-001
TITLE:
ASSEMBLY INSTRUCTIONS FOR
MX150L SEALED CONNECTOR
SYSTEM
SHEET No.
2 of 5
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
WLEUNG
DTITUS
DTITUS
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
MX150L ASSEMBLY INSTRUCTIONS
CONNECTOR RECEPTACLE ASSEMBLY
TERMINAL INSERTION
1. Begin assembly of the crimped female terminals into the receptacle housing by making
sure the Terminal Position Assurance feature (TPA) is in the pre-locked position (See
Figure 6).
• In pre-locked position, the dimension between receptacle housing face and TPA is
approximately 0.160” (4,06mm).
• If it is not in the pre-locked position, insert the blade of a screwdriver into the slots
in the TPA found adjacent or opposite to the latch. Apply slight pressure and pry
the TPA out until it clicks (See Figure 7). You are now ready to insert terminals
and/or circuit plugs.
TPA
Slots
TPA
0.160”
(4.06mm)
Figure 6: TPA in Pre-Lock Position
Figure 7: TPA Slots
2. The terminal must be positioned correctly when inserted into the housing to assure proper
latching and retention. Orient the key on the back of the female terminal with the keyway
on the wire entry cavity in the rear of the housing (See Figure 8). Insert the terminal into
the housing until it clicks and a slight pull back on the wire is met with resistance from
terminal retention feature.
Keyway in Wire Entry
Keyway on Terminal
Figure 8: Terminal Orientation
REVISION:
B
ECR/ECN INFORMATION:
EC No: IPG2013-0274
DATE: 2012 / 08 / 22
DOCUMENT NUMBER:
AS-19417-001
TITLE:
ASSEMBLY INSTRUCTIONS FOR
MX150L SEALED CONNECTOR
SYSTEM
SHEET No.
3 of 5
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
WLEUNG
DTITUS
DTITUS
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
MX150L ASSEMBLY INSTRUCTIONS
3. Repeat Step 2 until all terminals are inserted into the housing. If a terminal is inadvertently
assembled into the wrong position, use service tool to remove.
4. If using a circuit plug to seal an unused circuit, apply the same procedure as terminal
insertion above. Insert the circuit plug until it clicks twice and a slight pull back on the
circuit plug is met with resistance from terminal retention feature.
• DO NOT continue to push the circuit plug after the second audible click. The circuit
plug should rest on the second stop in the connector receptacle housing.
• In its final position, the dimension between the receptacle housing and the circuit
plug is approximately 0.285” (7,24mm) (See Figure 9 & Figure 10).
Keyway in Wire Entry
0.285”
(7.24mm)
Second Stop
Keyway on Circuit Plug
Figure 9: Circuit Plug Orientation
Figure 10: Circuit Plug in Final Position
5. When all terminals and/or circuit plugs are in their proper location, push down on TPA
until it clicks into place and is roughly flush or on same level as edge of outer housing
(See Figure 11).
TPA Flush with
Outer Housing
Figure 11: TPA in Locked Position
REVISION:
B
ECR/ECN INFORMATION:
EC No: IPG2013-0274
DATE: 2012 / 08 / 22
DOCUMENT NUMBER:
AS-19417-001
TITLE:
ASSEMBLY INSTRUCTIONS FOR
MX150L SEALED CONNECTOR
SYSTEM
SHEET No.
4 of 5
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
WLEUNG
DTITUS
DTITUS
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
MX150L ASSEMBLY INSTRUCTIONS
CONNECTOR POSITION ASSURANCE ACTIVATION
1. After mating the plug and receptacle connectors, push the Connector Position Assurance
feature (CPA) on the receptacle forward until it clicks or is as far forward towards mating
end of receptacle as possible (See Figure 12). This will prevent accidental depression of
latch and un-mating of connectors.
CPA in Forward Position
Figure 12: CPA in Locked Position
2. To un-mate connectors, pull CPA towards rear or wire entry end of receptacle. While
lightly pushing connectors together, depress latch and then pull the mated connectors
apart (See Figure 13).
Depress Latch to Un-mate
CPA in Pre-Locked Position
Figure 13: Connectors Un-mated
REVISION:
B
ECR/ECN INFORMATION:
EC No: IPG2013-0274
DATE: 2012 / 08 / 22
DOCUMENT NUMBER:
AS-19417-001
TITLE:
ASSEMBLY INSTRUCTIONS FOR
MX150L SEALED CONNECTOR
SYSTEM
SHEET No.
5 of 5
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
WLEUNG
DTITUS
DTITUS
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
很抱歉,暂时无法提供与“19420-0001”相匹配的价格&库存,您可以联系我们找货
免费人工找货