zQSFP+ 1-by-1 Cage Insertion Tool
1-by-1
Cage
Insertion Tool
Application Tooling
Specification Sheet
Order No. 200214-1110
FEATURES
Lightweight tool used in the insertion of a zQSFP+ cage in a PCB
Inserts connector to a PCB without damage to the board
SCOPE
Products: Small Form-Factor Pluggable zQSFP+ 1-by-1 Cages with Press-Fit PC Tails
Connector Series No.
100014-1231
100014-1240
100014-1340
100014-1346
100014-1443
100014-1540
100014-1546
100014-1643
100014-1744
100014
100014-1232
100014-1242
100014-1341
100014-1347
100014-1444
100014-1541
100014-1547
100014-1644
100014-6547
Connector Order No.
100014-1233 100014-1234
100014-1901 100014-1250
100014-1342 100014-1343
100014-1348 100014-1440
100014-1445 100014-1446
100014-1542 100014-1543
100014-1548 100014-1640
100014-1645 100014-1646
100014-1235
100014-1252
100014-1344
100014-1441
100014-1447
100014-1544
100014-1641
100014-1647
100014-1236
100014-1253
100014-1345
100014-1442
100014-1448
100014-1545
100014-1642
100014-1648
Notes:
1. See the following page for tooling operation instructions.
2. This tool requires a “Keep Out Zone” to be free of components. The tool overhangs the rear of the cage to
allow for light pipe options. The right and left sides should be .25” (6.4mm). See Figure 1.
CAGE ASSEMBLY
Figure 1
PCB
KEEP OUT
ZONE
Doc. No: ATS-2002141110
Revision: A
6.4mm Maximum
(BOTH SIDES)
Release Date: 04-04-17
Revision Date: 04-04-17
UNCONTROLLED COPY
Page 1 of 2
zQSFP+ 1-by-1 Cage Insertion Tool
Operation
1. By hand, place a cage assembly on the PCB. Make sure all compliant tails are engaged in PCB holes.
2. Place the tool on the cage assembly, oriented as shown in Figure 2.
3. Place the tool, cage, and PCB in a press of suitable size and force, and seat the cage as shown. The PCB
support (not furnished by Molex) must have clearance for the connector pins if they pass through the PCB.
Note: This insertion tool does not contact the PCB when the connector is fully seated.
CAGE
REAR
NOTE TOOL
ORIENTATION
CAGE
FRONT
Figure 2
INSERTION TOOL
OVER CAGE
ASSEMBLY
CAGE
ASSEMBLY
PCB
BOTTOM OF CAGE
TO SEAT FLUSH ON PCB
Application Tooling Support
Phone: +1-402-458-TOOL (8665)
E-Mail: applicationtooling@molex.com
Website: www.molex.com/applicationtooling
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other
trademarks listed herein belong to their respective owners.
Doc. No: ATS-2002141110
Revision: A
Release Date: 04-04-17
Revision Date: 04-04-17
UNCONTROLLED COPY
Page 2 of 2
很抱歉,暂时无法提供与“2002141110”相匹配的价格&库存,您可以联系我们找货
免费人工找货