2015913010

20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M A L ORIENTATION 400G 2X 18.35 ±0.10 400G L LABEL TEXT ORIENTATION LABEL TEXT K K LENGTH (SEE P/N TABLE) (SEE SHEET 3) J 2X 8.5 ±0.1 J 20±5 20±5 50 ±10 50 ±10 PCB VIEWING HOLES H DUST COVER TO BE PLACED ON ALL ENDS. PLACE ACETATE TAPE UNDER EACH LABEL DETAIL A SCALE 5:1 EXPANDO H G G P1 P2 CABLE LABEL (SEE SHEET 3) * FOR CABLES UNDER 2 METERS, ONLY ONE LABEL ON P1 END (LABEL SHOULD BE CENTERED ON TAPE) F F 76 REF 38 REF 13.25 REF E E D C B A D NOTES: 1. CABLE LENGTH DEPENDS ON WIRE GAUGE, DATA RATE, AND HOST BOARD DRIVER CAPABILITIES 2. MATERIALS: BACKSHELLS - ZINC DIE CAST WITH BRIGHT NICKEL PLATING DELATCH - STAINLESS STEEL WITH OVERMOLDED NYLON RIVETS - STAINLESS STEEL 3. IMPEDANCE - 100 OHMS DIFFERENTIAL 4. BUNDLED CABLE RATED UL VW-1 FLAME PER UL STYLE 21479 5. EEPROM MAP AVAILABLE UPON REQUEST 6. RoHS COMPLIANT, NO EXEMPTIONS DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/09/10 17 FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: SHEET4 : ADDED LENGTH 2M 30AWG IN P/N TABLE = = 15 14 13 0 mm 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 5.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 01:01:00 16 0 12 11 10 9 8 7 QSFP-DD TO QSFP-DD 56G PASSIVE CABLE ASY EC NO: 677116 DRWN: ADITHK CHK'D: VITTAD APPR: MGARRISON INITIAL REVISION: DRWN: TPRATT APPR: CHIRSCHY THIRD ANGLE PROJECTION 2021/05/24 2021/09/09 2021/09/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/08 2016/11/10 DRAWING 5 2015911005 MATERIAL NUMBER SERIES D-SIZE 201591 6 B GENERAL MARKET 3 U SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD 000 2 1 OF 4 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M CABLE BEND RADIUS 43 REF (MODULE HARD STOP TO BACK OF BEZEL) L BEZEL L K K NOTE: VIEW NOT TO SCALE. J J 22.8 REF MIN. BEND RADIUS OD H CABLE AWG OD (mm) MIN BEND RADIUS (mm) MIN BEND SPACE (mm) 26* 28 30 (13) (11) (9.4) (65) (55) (45) (101) (89) (77) MIN. BEND SPACE H *MINIMUM BEND RADIUS PENDING QUALIFICATION. NUMBERS ABOVE ARE ESTIMATES AND SUBJECT TO CHANGE. G ! G F F 37 39/1 38/76 E E 2 40 75 CUTAWAY2 CUTAWAY1 D D 56 59 C 20/58 21 57/19 A 18 = = TOP VIEW B FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: SHEET4 : ADDED LENGTH 2M 30AWG IN P/N TABLE BOTTOM VIEW DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/09/10 17 20:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0 5.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 01:01:00 16 0 mm ANGULAR TOL = NOTES: 1. DC BLOCKING CAPS ON RECEIVE SIDE ONLY 2. CABLE COILED AND PACKAGED IN BEST FIT ESD BAG AND SEALED WITH ESD LABEL FOR SHIPPING 0 15 14 13 12 11 10 9 8 7 QSFP-DD TO QSFP-DD 56G PASSIVE CABLE ASY EC NO: 677116 DRWN: ADITHK CHK'D: VITTAD APPR: MGARRISON INITIAL REVISION: DRWN: TPRATT APPR: CHIRSCHY THIRD ANGLE PROJECTION 2021/05/24 2021/09/09 2021/09/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/08 2016/11/10 DRAWING 5 2015911005 MATERIAL NUMBER SERIES D-SIZE 201591 6 B GENERAL MARKET 3 U SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD 000 2 2 OF 4 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M WIRING DIAGRAM L L P1 GND TX2N TX2P GND TX4N TX4P GND ModSelL RESETL VccRX SCL SDA GND RX3P RX3N GND RX1P RX1N GND GND RX2N RX2P GND RX4N RX4P GND ModPresL IntL VccTX Vcc1 LPMode GND TX3P TX3N GND TX1P TX1N GND GND TX6N TX6P GND TX8N TX8P GND Reserved VS1 VccRX1 VS2 VS3 GND RX7P RX7N GND RX5P RX5N GND GND RX6N RX6P GND RX8N RX8P GND N/C Reserved1 VccTX1 Vcc2 Reserved2 GND TX7P TX7N GND TX5P TX5N GND K J H G F E D C B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 1 2 3 4 5 6 7 8 9 0.1μF 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 5.1K 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 SHELL 2021/09/10 17 P2 100Ω 5.1K VCC 5.1K 5.1K 5.1K EEPROM 5.1K VCC 100Ω 5.1K 5.1K EEPROM 5.1K 20 21 22 23 24 25 26 27 28 5.1K 29 30 31 32 33 34 35 36 37 38 1 2 3 4 5 6 7 8 9 0.1μF 10 11 12 13 14 15 16 17 18 19 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 SHELL GND RX2N RX2P GND RX4N RX4P GND ModPresL IntL VccTX Vcc1 LPMode GND TX3P TX3N GND TX1P TX1N GND GND TX2N TX2P GND TX4N TX4P GND ModSelL RESETL VccRX SCL SDA GND RX3P RX3N GND RX1P RX1N GND GND RX6N RX6P GND RX8N RX8P GND N/C Reserved1 VccTX1 Vcc2 Reserved2 GND TX7P TX7N GND TX5P TX5N GND GND TX6N TX6P GND TX8N TX8P GND Reserved VS1 VccRX1 VS2 VS3 GND RX7P RX7N GND RX5P RX5N GND K J H G F E D FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: SHEET4 : ADDED LENGTH 2M 30AWG IN P/N TABLE = = 0 mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± = 0 5.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 01:01:00 16 0 15 14 13 12 11 10 9 8 7 QSFP-DD TO QSFP-DD 56G PASSIVE CABLE ASY EC NO: 677116 DRWN: ADITHK CHK'D: VITTAD APPR: MGARRISON INITIAL REVISION: DRWN: TPRATT APPR: CHIRSCHY THIRD ANGLE PROJECTION 2021/05/24 2021/09/09 2021/09/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/08 2016/11/10 DRAWING 5 2015911005 MATERIAL NUMBER SERIES D-SIZE 201591 6 B GENERAL MARKET 3 U SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD 000 2 3 OF 4 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M L L LABEL DETAILS 44.5 REF K P/N: 201591XXXX X.XXM XXAWG 12.70 REF YYDDDLSSSS J 19.05 REF S/N: YYDDDLSSSS 400G 400G 400G 57.15 REF 57.15 REF (CLEAR POLY WRAP) (CLEAR POLY WRAP) H G 25 REF P/N: 201591XXXX - MOLEX PART NUMBER (SEE P/N TABLE) F X.XXM - CABLE LENGTH IN METERS (EXAMPLES - 0.5M, 1.0M, 1.5M) SEE P/N TABLE FOR THE NUMBER OF DIGITS XXAWG - CABLE SIZE IN AWG S/N: YYDDDLSSSS - SERIAL NUMBER YY = YEAR, THE LAST 2 DIGITS OF YEAR DDD = DAY OF THE YEAR L = LOCATION 1 - USA 2 - MEXICO 3 - CHINA 4 - PHILIPPINES SSSS = SERIAL NUMBER (0001-9999) E D K J H G F E D *CABLES MAY NOT MEET ALL IEEE 802.3cd 56G PAM4 PARAMETERS C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: SHEET4 : ADDED LENGTH 2M 30AWG IN P/N TABLE = = B DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2021/09/10 17 0 mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0 5.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 01:01:00 16 0 ANGULAR TOL = A LENGTH (M) AWG 0.5M +/- 0.05M 30 0.75M +/- 0.05M 30 1.0M +/- 0.05M 30 1.25M +/- 0.05M 30 1.5M +/- 0.08M 30 2.0M +/- 0.08M 30 0.5M +/- 0.05M 28 1.0M +/- 0.05M 28 1.25M+/- 0.05M 28 1.5M +/- 0.08M 28 1.75M +/- 0.08M 28 2.0M +/- 0.08M 28 2.5M +/- 0.08M 28 2.5M +/- 0.08M 26 2.75M +/- 0.08M 26 3.0M +/- 0.08M 26 MOLEX P/N 2015911005* 2015911007 2015911010 2015911012 2015911015 2015911020 2015913005* 2015913010 2015913012 2015913015 2015913017 2015913020 2015913025 2015913252 2015913027 2015913030 15 14 13 12 11 10 9 8 7 QSFP-DD TO QSFP-DD 56G PASSIVE CABLE ASY EC NO: 677116 DRWN: ADITHK CHK'D: VITTAD APPR: MGARRISON INITIAL REVISION: DRWN: TPRATT APPR: CHIRSCHY THIRD ANGLE PROJECTION 2021/05/24 2021/09/09 2021/09/10 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/11/08 2016/11/10 DRAWING 5 2015911005 MATERIAL NUMBER SERIES D-SIZE 201591 6 B GENERAL MARKET 3 U SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD 000 2 4 OF 4 1 A