2033721253

20 M 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 3D MODEL: 2033721201 PSM ASY M BASE CAGE DETAILS 2033721244 SHOWN L L 114.85 REF CLOSE TOP K J K J 71.57 REF H H SPRING FINGER G FROM THE EDGE OF CAGE COVER 115.59 REF (UNCOMPRESSED) DIMENSIONS OF EACH INNER CAGE DESIGNED TO FUNCTION WITH QUAD SMALL FORM-FACTOR (zQSFP+ & QSFP-DD) TRANSCEIVER 18.75 ±0.10 (INSIDE TO INSIDE) F E 13.40 REF. FROM THE EDGE OF CAGE COVER NOTES: 1. MATERIAL: CAGE: STAINLESS STEEL CENTER WALLS: STAINLESS STEEL SPRING FINGERS: STAINLESS STEEL HEAT SINK: ALUMINUM(BLACK ANODIZATION) HEAT SINK CLIP: STAINLESS STEEL 2. DRAWING APPLIES TO ALL P/N'S SHOWN ON PAGE 3 3. DURING FINAL INSPECTION, CAGE LEG LOCATIONS AND STRAIGHTNESS MUST BE CHECKED USING APPROPRIATE GO - NO GO GAGE 4. DURING FINAL INSPECTION, CAGE MUST BE INSPECTED TO MAKE SURE LEG CONFIGURATIONS AND PART NUMBERS ARE CORRECT, REFER TO SHEETS 3. 5. PARTS TO BE INSPECTED PER MOLEX COSMETIC SPEC WI-HP-7-2774 (CLASS B UNLESS OTHERWISE SPECIFIED) 6. PRESS-FIT LEGS 2.20mm LONG 1.57mm MINIMUM PCB THICKNESS FOR SINGLE SIDED USE. 2.70mm MINIMUM PCB THICKNESS FOR BELLY TO BELLY USE. 7. NO RoHS EXEMPTIONS. 8. WELD SPOT MAY SHOW SLIGHT MATERIAL DISCOLORATION. C B DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 9.75 REF. E 8.96 ±0.10 (INSIDE TO INSIDE) D 203372XXXX WKYR P/N AND WEEK/YEAR DATE CODE TO BE PRINTED ON SIDE OF COMPLETED CAGE ASSEMBLY APPROXIMATELY AS SHOWN. SEE TABLE BELOW FOR DATE CODE INFORMATION. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 2:1 14 13 12 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15 D WEEK/YEAR DATE CODE TABLE WK WEEK OF THE YEAR 01 THRU 52 OR 53 (EXAMPLE: 01= FIRST WEEK OF YEAR, 52 OR 53 = LAST WEEK OF YEAR YR 17, 18, 19 ETC.. (EXAMPLE: YEAR 2017= 17) 10:48:55 16 G F SEE NOTE 8 10.80 REF. (UNCOMPRESSED) A REAR LEGS OPTIONAL (SEE TABLE ON SHEET 3) 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 5 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES D-SIZE 203372 6 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S GENERAL MARKET 3 D3 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD ASY 2 1 OF 7 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M CAGE ASSEMBLY OPTIONS L L 2033722346 SHOWN HEAT SINK CLIP K K HEAT SINK J J H H WITH RAISED BASE G G SPRING FINGER F F 1 DIM "A" MAX. E E REAR LEG OPTIONS D HEAT SINK HEIGHT OPTIONS D OVERALL HEAT SINK HEIGHT DIM "A" 13.7 PCI 16.0 SAN NET 23.0 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) 0 REAR LEGS B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 HEIGHT OF HEAT SINK WITH MODULE INSERTED. 1 DIMENSION MAY BE LESS DUE TO MODULE AND HEAT SINK VARIATIONS. 1 REAR LEG ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:48:55 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 5 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES D-SIZE 203372 6 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S GENERAL MARKET 3 D3 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD ASY 2 2 OF 7 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M PART NUMBER SELECTION L L OPEN TOP CLOSED TOP WITH HEAT SINK K K J J H H G # OF REAR LEGS WITH RAISED BASE PER PORT 2033721243 0 NO 2033721244 1 NO MOLEX P/N MOLEX P/N 2033721253 2033721254 2033722253 2033722254 F # OF REAR LEGS WITH RAISED BASE PER PORT 0 NO 1 NO 0 YES 1 YES MOLEX P/N 2033721346 2033721347 2033721348 2033721349 2033721350 2033721351 2033722346 2033722347 2033722348 2033722349 2033722350 2033722351 E WITHOUT RAISED BASE G # OF REAR LEGS HEAT SINK WITH RAISED BASE PER PORT 0 PCI NO 0 SAN NO NET 0 NO 1 PCI NO 1 SAN NO NET 1 NO 0 PCI YES 0 SAN YES NET 0 YES 1 PCI YES 1 SAN YES NET 1 YES F E WITH RAISED BASE D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:48:55 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES 5 GENERAL MARKET 4 3 D3 SHEET NUMBER CUSTOMER D-SIZE 203372 6 PSD ASY 2 3 OF 7 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M PCB LAYOUT FOR SINGLE SIDED MOUNTING HOST CONNECTOR DETAIL L L 1.00 TYP. 114.00 17.00 TYP. 95.00 15.02 MAX. 76.00 12X ⌀ 1.55 ±0.05 ⌖ ⌀0.05 A L 57.00 38.00 K 19.00 HATCHED AREA DENOTES COMPONENT KEEP-OUT AND NO SURFACE TRACES. (EXCEPT CHASSIS GROUND) 1.69 MAX. TYP. C 16.80 K 3.05 MIN. TYP. 37.00 MAX. J J 34.60 30.10 41X ⌀ 1.05 ±0.05 ⌖ ⌀0.05Ⓜ A L-K C 22.85 MAX. 23.85 MIN. 25.60 21.10 H H 16.60 12.10 7.60 3.10 G G 0.00 K F L DETAIL 1 SCALE 4:1 3.10 AREA DENOTES COMPONENT KEEP-OUT AND NO SURFACE TRACES.(EXCEPT CHASSIS GROUND) 2X 2.10 7.60 2X 1.20 NO REAR LEGS F DATUM C 23.10 -A- E E DATUM -A- IS THE TOP SURFACE OF HOST BOARD SEE DETAIL 1 113.90 D 110.78 92.28 73.28 54.28 35.28 19.00 112.90 16.28 4.50 HOLE OF ADJACENT CAGE 1.10 D 17.90 0.00 CROSS HATCHED AREA DENOTES COMPONENT KEEP-OUT AND NO SURFACE TRACES. (EXCEPT FOR CHASSIS GROUND) PARTIAL 1 SCALE 4:1 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B NOTES: 1. PADS AND VIAS GO TO CHASSIS GROUND. (RECOMMENDED PADS TO BE 2.00x4.00mm RECTANGLE.) 2. RECOMMENDED THRU HOLE PLATING INCLUDES HASL, OSP, OR IMMERSION (GOLD, SILVER, OR TIN). 3. CONNECTOR PAD LAYOUT PER QSFP-DD MSA WILL ACCOMODATE MOLEX CONNECTOR SERIES 202718. A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 15 14 13 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:48:55 16 ANGULAR TOL 12 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 5 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES D-SIZE 203372 6 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S GENERAL MARKET 3 D3 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD ASY 2 4 OF 7 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M PCB LAYOUT FOR BELLY TO BELLY MOUNTING L L 114.00 95.00 K K 76.00 57.00 HATCHED AREA DENOTES COMPONENTK EEP-OUT AND NO SURFACE TRACES. (EXCEPT CHASSIS GROUND) 38.00 19.00 C 16.80 J J 37.00 MAX. -ADATUM -A- IS THE TOP SURFACE OF HOST BOARD 34.60 30.10 H H 25.60 NOTE: SEE SHEET 4 FOR HOST CONNECTOR DETAIL 21.10 77X ⌀ 1.05 ±0.05 16.60 ⌖ ⌀0.05Ⓜ A L-K C 12.10 G G 7.60 AREA DENOTES COMPONENT KEEP-OUT AND NO SURFACE TRACES.(EXCEPT CHASSIS GROUND) 3.10 K 0.00 L 3.10 F F 7.60 DATUM C CROSS HATCHED AREA DENOTES COMPONENT KEEP-OUT AND NO SURFACE TRACES. (EXCEPT FOR CHASSIS GROUND) E 23.10 HOLES FOR OPTIONAL REAR LEGS D 110.78 95.52 92.28 76.52 93.90 73.28 57.52 74.90 54.28 55.90 38.52 35.28 36.90 19.52 16.28 E 1.10 4.50 HOLE OF ADJACENT CAGE 1.02 D 17.90 0.00 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 3:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B NOTES: 1. PADS AND VIAS GO TO CHASSIS GROUND. (RECOMMENDED PADS TO BE 2.00x4.00mm RECTANGLE.) 2. RECOMMENDED THRU HOLE PLATING INCLUDES HASL, OSP, OR IMMERSION (GOLD, SILVER, OR TIN). 3. CONNECTOR PAD LAYOUT PER QSFP-DD WILL ACCOMODATE MOLEX CONNECTOR SERRIES 202718. A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 15 14 13 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:48:55 16 ANGULAR TOL 12 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 5 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES D-SIZE 203372 6 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S GENERAL MARKET 3 D3 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD ASY 2 5 OF 7 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M BEZEL AND BOARD POSITION DIMENSIONS FOR SINGLE SIDE MOUNTING BEZEL AND BOARD POSITION DIMENSIONS FOR BELLY TO BELLY MOUNTING L L 43.8 REF. (BEZEL CENTERLINE) 43.3 ±0.3 (BACK OF BEZEL) CUTAWAY 1 43.8 REF. (BEZEL CENTERLINE) CUTAWAY 2 43.3 ±0.3 (BACK OF BEZEL) K J 0.15 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE 2X 9.75 REF. (TOP OF CAGE TO PAD SURFACE) CUTAWAY 4 K 0.15 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE 0.15 ±0.10 BEZEL OPENING ABOVE PCB PAD SURFACE 9.75 REF. (TOP OF CAGE TO PAD SURFACE) J CUTAWAY 3 8.70 REF. 1.00 REF 1.00 REF. H H G G 10.15 ±0.10 10.15 ±0.10 SEE NOTE 1 F F 10.15 ±0.10 E R 0.30 MAX. TYP. 2X 115.00 ±0.10 2 2.40 MIN. R 0.30 MAX. TYP. 115.00 ±0.10 2 2.40 MIN. E D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 2.5:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B A NOTE: 1. PCB THICKNESS VARIATION MUST BE CONSIDERED WHEN DETERMINING BEZEL OPENING LOCATION. 2 THIS DIMENSION IS FOR REFERENCE ONLY. USER CAN MODIFY UT DEPENDS ON APPLICATION. (THIS DIMENSION VARIES BASED ON DISTANCE OF "HOLE OF ADJACENT CAGE" ON PCB LAYOUT. DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:48:55 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 5 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES D-SIZE 203372 6 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S GENERAL MARKET 3 D3 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD ASY 2 6 OF 7 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M REV A A1 B L C K J H DATE DESCRIPTION 2017/07/25 INITIAL RELEASE 2017/08/30 SHEET 4: G11: UPDATED OPEN TOP ISO VIEW. 2017/11/03 SHEET 4: H18: AS PER THE QSFP-DD MSA TO CORRECTED TP TOLERANCE FROM 0.1 TO 0.05mm. K06: AS PER THE QSFP-DD MSA TO ADDED TP TOLERANCE AS 0.05MM AND CHANGED 1.55REF. TO 1.55±0.05mm.. SHEET 5: G17: AS PER THE QSFP-DD MSA TO CORRECTED TP TOLERANCE FROM 0.1 TO 0.05mm. 2018/03/19 SHEET 1: K17: ADDED DIMENSION 114.85 REF. SHEET 2: E04: ADDED A BACK VIEW. SHEET 4: H18: CHANGED "TYP." TO "41X" OF DIMENSION 1.05mm. H18: UPDATED TRUE POSITION DATUM FROM A, K AND L TO A, L-K AND C. J10: AS PER THE QSFP-DD MSA TO ADDED BASIC DIMENSION 16.80 AND DATUM C. K06 : CHANGED "TYP." TO "12X" OF DIMENSION 1.55mm. SHEET 5: G17: CHANGED "TYP." TO "77X" OF DIMENSION 1.05mm. G17: UPDATED TRUE POSITION DATUM FROM A, K AND L TO A, L-K AND C. J08: AS PER THE QSFP-DD MSA TO ADDED BASIC DIMENSION 16.80 AND DATUM C. K J OPEN TOP SERIES RELLOCATED TO DRAWING NUMBER 2033722201. SHEET 3(C18) & SHEET(E18) : UPDATE RECOMMEND PCB LAYOUT OF TRACE KEEP-OUT ZONE. D 2019/05/02 D1 D2 2019/07/15 SHEET 3: ADDED NEW P/Ns(-2XXX, WITH RAISED BASE). 2019/08/05 SHEET 3 : 5G : ADDED A COLUMN FOR TYPES OF HEAT SINK. SHEET 6 : F2 & E11 : CHANGED R0.30 TYP. TO R0.30 MAX. TYP. SHEET 6 : J8 & H17 : CHANGED BEZEL THICKNESS FROM 1.60 REF. TO 1.00 REF. 2019/12/13 SHEET 6 : K6 & L16 : CHANGED FROM 43.0 ±0.3 TO 43.3 ±0.3 SHEET 6 : J7 : CHANGED FROM 8.40 REF. TO 8.70 REF. D3 L H G G F F E E D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 1:1 CURRENT REV DESC: SEE REVISION TABLE GENERAL TOLERANCES (UNLESS SPECIFIED) B A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 20 19 P1 RELEASE DATE 18 2019/12/20 17 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:48:55 16 ANGULAR TOL 15 14 13 12 11 10 9 8 7 EC NO: 629406 DRWN: JYEN01 CHK'D: SCHIEN APPR: JCHIANG INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION DRAWING 2019/12/13 2019/12/20 2019/12/20 5 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/07/20 2017/08/15 2033721201 MATERIAL NUMBER SERIES D-SIZE 203372 6 QSFP-DD 1X6 GANGED CAGE ASSY SPRING FINGER WITH FIN H/S GENERAL MARKET 3 D3 SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD ASY 2 7 OF 7 1 A