2065663020

20 19 18 17 16 15 14 13 12 10 11 9 7 8 5 6 4 3 2 1 M M LEG ID LABEL (SEE SHEET 3) PCB VIEWING HOLES L L P2 P2 LABEL TO BE CENTERED OVER ACETATE TAPE 4X 50 ±10 5X 18.35 ±0.10 P1 20 ±5 LABEL TEXT ORIENTATION 50 ±10 A P3 P3 P4 P4 DETAIL A SCALE 2:1 K 400G K CABLE LABEL (SEE SHEET 3) J PCB VIEWING HOLES J B P5 P5 H H DETAIL B SCALE 2:1 LENGTH (SEE P/N TABLE) EXPANDO G 50 ±5 G 5X 8.5 ±0.1 HEATSHRINK 180 REF. (EXPANDO FROM EXIT) 76 REF 38 REF F F QSFP-DD ASSEMBLY (P1 END) 13.8 REF 70 REF. E 38 REF. E zQSFP+ ASSEMBLY - 30AWG (P2-P5 END) 12.6 REF. D C B A NOTES: 1. CABLE LENGTH DEPENDS ON WIRE GAUGE, DATA RATE, AND HOST BOARD DRIVER CAPABILITIES 2. MATERIALS: BACKSHELLS - ZINC DIE CAST WITH BRIGHT NICKEL PLATING DELATCH - STAINLESS STEEL WITH OVERMOLDED NYLON RIVETS - STAINLESS STEEL 3. IMPEDANCE - 100 OHMS DIFFERENTIAL 4. CABLE IS UL RECOGNIZED (TBD) 5. EEPROM MAP AVAILABLE UPON REQUEST 6. RoHS COMPLIANT, NO EXEMPTIONS 7. ASSEMBLY TO BE SHIPPED WITH DUST COVERS INSTALLED ON ALL CABLE ENDS DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2023/04/19 17 70 REF. 38 REF. D FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: SHEET3 : IN ZONE G8 TEXT " *CABLES MAY NOT MEET ALL SI PARAMETERS OF = 0 IEEE 802.3CD " ADDED. mm = 0 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 2 PLACES ± 0.13 1 PLACE ± 0.25 0 PLACES ± 0 5.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 15 14 13 12 11 10 9 8 C 1:1 ANGULAR TOL = 15:28:59 16 zQSFP+ ASSEMBLY - 28AWG (P2-P5 END) 13.0 REF. 7 QSFP-DD TO (4) ZQSFP+ 56G CABLE ASY EC NO: 746689 DRWN: KIRANG5 CHK'D: VITTAD APPR: SCHANNARAYAN INITIAL REVISION: DRWN: GWATERWORTH APPR: ADTUCKER THIRD ANGLE PROJECTION 2023/04/12 2023/04/14 2023/04/19 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/12/07 2017/12/14 DRAWING 5 2065661000 MATERIAL NUMBER SERIES D-SIZE 206566 6 B GENERAL MARKET 3 H SHEET NUMBER CUSTOMER SEE P/N TABLE 4 PSD 000 2 1 OF 3 1 A 20 19 18 17 16 15 14 13 12 10 11 9 7 8 M zQSFP+ CABLE BEND RADIUS L 38 20 BEZEL 01 19 LOW SPEED SIGNALS P1, P2, P3, P4, & P5 PAD SIGNAL 8 MODSELL 9 RESETL K 22.8 REF MIN. BEND RADIUS J OD NOTE: VIEW NOT TO SCALE. MIN. BEND SPACE H CABLE AWG OD (mm) MIN BEND RADIUS (mm) MIN BEND SPACE (mm) 26 6.8 34 63.6 28 6.5 32.5 61.8 30 5.9 29.5 58.2 G QSFP-DD CABLE BEND RADIUS F 37 10 11 12 27 28 29 30 31 VCCRX SCL SDA MODPRSL INTL VCCTX VCC1 INIT_MODE 46 47 48 49 50 65 66 67 68 69 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN 38/76 5 6 4 WIRING DIAGRAM QSFP-DD zQSFP+ PAD SIGNAL PAD SIGNAL LEG ---- 20 1 GND GND P2 ---> 21 2 TX2n RX2n ---> 22 3 TX2p RX2p 4 ---- 20 GND GND 5 TX4n ---> 21 RX2n TX4p ---> 22 6 RX2p 7 ---GND GND P3 ---13 GND GND 22 TX8p RX2p 45 ---GND GND P5 ---51 GND GND RX7p