2147210090

10 9 7 8 5 6 4 NOTES 1 F 2. C 3. 4. 5. E 材料及び仕上げ(めっき仕様)：TABLE1参照 MATERIAL AND FINISES:SEE TABLE 1 製品仕様：2147190000-PS 000 PRODUCT SPECIFICATION：2147190000-PS 000 梱包仕様：2147219200-SPK 200 PACKING SPECIFICATION：2147219200-SPK 200 嵌合相手：214719 SERIES MATE WITH：214719 SERIES アプリケーション仕様書 (コネクタ取扱い説明書)：2166940000-AS 000 APPLICATION SPECIFICATION (CONNECTOR MANUAL)：2166940000-AS 000 B 2.5 TRADE MARK 9. 本製品のプラスチック部に黒点、白点等が確認される場合や 色合いが異なる場合がありますが、製品機能に影響はありません。 THERE IS NO INFLUENCE IN THE PRODUCT PERFORMANCE THOUGH THE BLACK AND WHITE SPOT ETC. MIGHT BE CONFIRMED TO THE PLASTIC PART OF THIS PRODUCT AND THE SHADE MIGHT BE DIFFERENT. CAV.&MOLD NO. 18.8 18.0 17.2 16.4 15.6 14.8 14.0 13.2 12.4 11.6 10.8 10.0 9.2 8.4 7.6 6.8 6.0 5.2 4.4 1.6 0.5 (0.8) (0.4) (PITCH) 0.7 7 ①HOUSING 2.35 ②TERMINAL 1 TABLE 1 C 番号 部品 NO. PART ① 材質 MATERIAL ハウジング 液晶ポリマー(LCP), UL94 V-0, LOW HALOGEN, 黒 HOUSING LIQUID CRYSTAL POLYMER(LCP), UL94 V-0, LOW HALOGEN, BLACK 銅合金 COPPER ALLOY B ② ターミナル ニッケルめっき(下地)：1.0 MICROMETER MINIMUM TERMINAL NICKEL (UNDER PLATING) E 錫めっき(リフロー処理)：1.0 MICROMETER MINIMUM MATTE TIN REFLOW TREATMENT ③ A DOCUMENT STATUS ニッケルめっき(下地)：1.0 MICROMETER MINIMUM NICKEL (UNDER PLATING) P1 RELEASE DATE 9 2022/01/28 15.2 14.4 13.6 12.8 12 11.2 10.4 9.6 8.8 8 7.2 6.4 5.6 4.8 4 3.2 2.4 1.6 0.8 18.28 17.48 16.68 15.88 15.08 14.28 13.48 12.68 11.88 11.08 10.28 9.48 8.68 7.88 7.08 6.28 5.48 4.68 3.88 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 D C B A 極数 CIRCUIT SIZE 5.6 3.2 D C B DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) 錫めっき(リフロー処理)：1.0 MICROMETER MINIMUM MATTE TIN REFLOW TREATMENT FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 2.9 2.1 1.3 18.2 17.4 16.6 15.8 15 14.2 13.4 12.6 11.8 11 10.2 9.4 8.6 7.8 7 6.2 5.4 4.6 3.8 E THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION リン青銅 PHOSPHOR BRONZE ネイル NAIL F 極数 CIRSUIT SIZE シリーズ番号 SERIES No. ③NAIL D 1 214721　0 * * 0 CIRCUIT N CIRCUIT 1 2 6. 端子テール部及びネイルの平坦度：0.1MAX. TAIL AND NAIL COPLANARITY TO BE 0.1 MAX. 極数/2 = 偶数に適応 7 APPLY FOR CIRCUIT SIZE / 2 = EVEN 発注番号(製品番号)：SHEET 4の製品一覧を参照ください 8 ORDER No (MATERIAL No)： REFER TO SHEET 4 FOR PRODUCT LIST A CIRCUIT 1 INDICATOR MARK 3 7 ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:34:50 8 ANGULAR TOL 6 5 4 ZERO-HACHI 0.8 HDR SINGLE ROW RA ASSY EC NO: 693607 DRWN: HKOBAYASHI CHK'D: AIDA APPR: SAKIYAMA INITIAL REVISION: DRWN: HKOBAYASHI APPR: SAKIYAMA THIRD ANGLE PROJECTION 2021/07/12 2022/01/28 2022/01/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/07/12 2022/01/28 DRAWING SERIES 2147210000-SD MATERIAL NUMBER CUSTOMER A3-SIZE 214721 3 GENERAL 2 PSD 000 A SHEET NUMBER 1 OF 4 1 A 10 9 7 8 6 5 4 3 2 1 F F (C) 10.2 (B) (1.65) 0.8 ±0.05 0.4 0.5 ±0.05 E E 1.0 ±0.1 2.3 ±0.1 (4.1) (E) D 嵌合相手：214719シリーズ MATE WITH:214719 SERIES コネクタ外形 1.2 ±0.1 0.7 ±0.1 CONNECTOR OUTLINE 嵌合状態図 MATED CONNECTORS 推奨基板パターンレイアウト(参考) RECOMENDED PCB PATTERN LAYOUT(REF.) (参考：メタルマスク厚さ 0.1mm, マスク開口率100％) (REF:METAL MASK THICKNESS 0.1mm, APERTURE RATIO 100%) C ( 1.75 MAX.) D 1.7 ±0.1 (1.6) (1.05) (2.1) (PITCH) (D) SUCTION AREA 5.60 (0.4) パターン非推奨エリア パターンを引き回す際は、製品機能に影響がないことをご確認ください。 PATTERN IS NOT RECOMMENDED ON THE HATCHING AREA PLEASE CHECK NOT TO HAVE PROBLEM FOR PRODUCT FUNCTION WHEN SETTING PATTERN ON THE HATCHING AREA. 吸着範囲 SUCTION AREA B C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/01/28 ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:34:50 8 ANGULAR TOL 7 6 5 4 ZERO-HACHI 0.8 HDR SINGLE ROW RA ASSY EC NO: 693607 DRWN: HKOBAYASHI CHK'D: AIDA APPR: SAKIYAMA INITIAL REVISION: DRWN: HKOBAYASHI APPR: SAKIYAMA THIRD ANGLE PROJECTION 2021/07/12 2022/01/28 2022/01/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/07/12 2022/01/28 DRAWING SERIES 2147210000-SD MATERIAL NUMBER CUSTOMER A3-SIZE 214721 3 GENERAL 2 PSD 000 A SHEET NUMBER 2 OF 4 1 A 10 9 7 8 5 6 4 送り穴のズレ量0.05MAX SKEW:0.05MAX X 2 1 NOTES 梱包数量：5,000個 NUMBER OF CONNECTORS:5,000PIECES/REEL リードテープ長さ LEAD TAPE LENGTH トップテープ接着部(空エンボス) 引き出し方向　　　　 PULL OUT DIRECTION F 3 32mmテープ TAPE WIDTH F 100 MIN. TOP TAPE BONDED PART(EMPTY) 24mmテープ TAPE WIDTH W (2.39) 引き出し方向 (0.4) 16mmテープ TAPE WIDTH 400 MIN. F コネクタ CONNECTOR CENTER OF COMMECTOR コネクタ 中心位置 (H) ⑤トップテープ D TOP TAPE 33.5 14.2 28.4 SECTION X-X ⌀ 1.5 +0.1 0 TYP.(N) 8.0 +0.1 0 C (2.0) (2) エンボスポケット中心位置 R 0.75 +0.05 0 CENTER OF EMBOSSED POCKET TYP.(2) 32±0.3 (30°) (30°) 0.2 ±0.05 TYP.(N) 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 (90°) 1.75 ±0.1 X 4 ±0.1 累積ピッチ：40±0.2 25.5 11.5 - 24+0.3/-0.1 17.5 7.5 - 16+0.3/-0.1 (⌀ 13) ACCUMULATIVE PITCH ⑥ REEL 1.5 +0.1 0 引き出し方向 PULL OUT DIRECTION DETAIL W SCALE 5:1 (⌀ 25) (⌀ 21) (R 35) DETAIL W ④ A ⑤ ⑥ 材質 MATERIAL ⌀380 ±2.0 �⌀80� B 番号 部品 No. PART DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 DETAIL W ポリエチレン(PE),その他 POLYETHYLENE(PE), etc リール REEL 2.0 ±0.5 ポリスチレン(PS) POLYSTYLENE P1 RELEASE DATE 9 2022/01/28 J ±0.5 TYP.(2) G C B 極数 エンボステープ幅F WIDTH OF TAP F CIRCUIT SIZE THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:34:50 8 H J D CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) ポリスチレン(PS) エンボステープ EMBOSSED TAPE POLYSTYLENE(PS), etc トップテープ TOP TAPE E トップテープの剥離強度はIEC60286-3に準拠。 TOP TAPE PELING FORCE IS DEFINED BY IEC60286-3. 梱包仕様書：2147219200-SPK PS 200 PACAGING SPECIFICATION:2147219200-SPK PS 200 ④エンボステープ EMBOSSED TAPE 末端部(空部) TAIL PART (EMPTY) 500 MIN. 部品挿入部 COMPONENT SUPPLIER PULL OUT DIRECTION G ±0.1 E 7 6 5 4 ZERO-HACHI 0.8 HDR SINGLE ROW RA ASSY EC NO: 693607 DRWN: HKOBAYASHI CHK'D: AIDA APPR: SAKIYAMA INITIAL REVISION: DRWN: HKOBAYASHI APPR: SAKIYAMA THIRD ANGLE PROJECTION 2021/07/12 2022/01/28 2022/01/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/07/12 2022/01/28 DRAWING SERIES 2147210000-SD MATERIAL NUMBER CUSTOMER A3-SIZE 214721 3 GENERAL 2 PSD 000 A SHEET NUMBER 3 OF 4 1 A 10 9 7 8 5 6 4 3 2 1 半嵌合防止形状(11極～20極） F INCOMPLETE MATING PREVENTION SHAPE (11~20 CIRCUIT) F 嵌合確認コア MATING CHECK CORE E CIRCUIT2 CIRCUIT N-1 CIRCUIT3 CIRCUIT N-2 E 発注番号一覧 ORDER NUMBER LIST 8 ハウジング色 HOUSING COLOR 20 19 18 D 17 16 15 14 13 12 11 10 C 9 8 7 6 5 4 3 2 黒 BLACK 214721 0200 214721 0190 214721 0180 214721 0170 214721 0160 214721 0150 214721 0140 214721 0130 214721 0120 214721 0110 214721 0100 214721 0090 214721 0080 214721 0070 214721 0060 214721 0050 214721 0040 214721 0030 214721 0020 Y D 端子露出部 EXPOSED TERMINAL 半嵌合状態では嵌合確認コアの DETAIL Y 圧着端子が露出しています SCALE 10:1 THE EXPOSED TERMINAL CONTACTS IN MATING CHECK CORE INDICATES THE CRIMP HOUSING IS NOT COMPLETELY MATED TO THE HEADER. 半嵌合 INCOMPLETE MATING C B 発注番号 ORDER NO. Z 梱包形態：エンボスリール PACKAGE:EMBOSSED REEL 極数 CIRCUIT SIZE B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DETAIL Z SCALE 10:1 正しい位置まで嵌合すると嵌合確認コアの 圧着端子が隠れて目視出来なくなります。 A DOCUMENT STATUS P1 RELEASE DATE 9 2022/01/28 嵌合完了 MATING COMPLETE NTS ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:34:50 8 SCALE mm CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) WHEN THE TERMINAL CONTACTS IN MATING CHECK CORE ARE NOT EXPOSED, IT INDICATES THE CRIMP HOUSING IS COMPLETELY MATED TO THE HEADER. FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 DIMENSION UNITS 7 6 5 4 ZERO-HACHI 0.8 HDR SINGLE ROW RA ASSY EC NO: 693607 DRWN: HKOBAYASHI CHK'D: AIDA APPR: SAKIYAMA INITIAL REVISION: DRWN: HKOBAYASHI APPR: SAKIYAMA THIRD ANGLE PROJECTION 2021/07/12 2022/01/28 2022/01/28 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/07/12 2022/01/28 DRAWING SERIES 2147210000-SD MATERIAL NUMBER CUSTOMER A3-SIZE 214721 3 GENERAL 2 PSD 000 A SHEET NUMBER 4 OF 4 1 A