2153610064

10 9 7 8 6 5 4 3 2 1 CONFIDENTIAL F NOTES 1. RE DETAILED DIMENSION, SEE PRODUCT DRAWING. 2. NUMBER OF CONNECTORS : 20000PCS/REEL 3. LEAD TAPE LENGTH. REEL PULL OUT DIRECTION 100 MIN. TOP TAPE BONDED PART. (EMPTY) ⌀ 380 ±2 E �⌀80� PULL OUT DIRECTION E TOP TAPE LEADER PART 400MIN. "D" D COMPONENT SUPPLIER TAIL PART (EMPTY) 160 MIN. D E ±1 4. PEELING OFF FORCE OF THE TOP TAPE IS DEFINED BY IEC60286-3. 5. MATERIAL CARRIER TAPE : POLYSTYRENE OR PET TOP TAPE : PET , OTHER REEL : POLYSTYRENE (PS) ＜RECYCLE MATERIAL CONTAINED＞ F ±1 C F C (⌀10) (120 °) (22) (2) B B (⌀21) (⌀13) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DETAIL "D" DOCUMENT STATUS P1 RELEASE DATE 9 2021/06/30 SCALE mm 1:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A FORMAT: master-tb-prod-A3 REVISION: J DATE: 2020/01/14 DIMENSION UNITS ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:16:52 8 ANGULAR TOL 7 6 5 4 EC NO: 668673 DRWN: RMIYAMOTO CHK'D: KSASAKI APPR: YKOBAYASHI02 INITIAL REVISION: DRWN: RMIYAMOTO APPR: YKOBAYASHI02 THIRD ANGLE PROJECTION DRAWING 5G15 (6+4P RF) PLUG EMBOSS PACKAGE 2021/06/30 2021/06/30 2021/06/30 2021/06/25 2021/06/30 SERIES A3-SIZE 215361 3 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2153610000-SD MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 000 A SHEET NUMBER 1 OF 2 1 A 10 9 7 8 5 6 4 3 2 1 CONFIDENTIAL F F PULL OUT DIRECTION 4 ±0.1 �1.64� �2.5� B TOP TAPE E �1.08� D (J) 1.75 ±0.1 0.3 ±0.05 A H ±0.05 G ±0.3 E SECTION B-B B ⌀ 1.5 +0.1 0 4 ±0.1 A D ACCUMULATIVE PITCH 40±0.2 C SECTION A-A �0.68� 2.5 ±0.05 B C 2153610064 7.5 2.33 16 21.4 ORDER NO. J H G F CONNECTOR SERIES No. --6 〇 HIGH VOL. LOW VOL. TOOL TOOL SAMPLE PREPARATION E Ckt. ○：TOOLED △：WORK IN PROCESS ---：TOOLING TO BE CONFIRMED 215361**** 17.4 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 9 2021/06/30 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:16:52 8 ANGULAR TOL 7 6 5 4 EC NO: 668673 DRWN: RMIYAMOTO CHK'D: KSASAKI APPR: YKOBAYASHI02 INITIAL REVISION: DRWN: RMIYAMOTO APPR: YKOBAYASHI02 THIRD ANGLE PROJECTION DRAWING 5G15 (6+4P RF) PLUG EMBOSS PACKAGE 2021/06/30 2021/06/30 2021/06/30 2021/06/25 2021/06/30 SERIES A3-SIZE 215361 3 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2153610000-SD MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 000 A SHEET NUMBER 2 OF 2 1 A 10 9 7 8 5 6 4 3 2 1 CONFIDENTIAL A ±0.05 F F X B ±0.1 0.35 2.1 ±0.08 (PITCH) 1.14 ±0.1 (PICK UP AREA) E 0.12 ±0.05 E ⌖ 0.15 X (TERM WIDTH) (2.1) (B) 0.38 ±0.1 1.67 ±0.05 0.38 ±0.1 D D 0.98 ±0.1 0.14 ±0.05 0.2 ±0.05 FITTING NAIL (FITTING NAIL WIDTH) (FITTING NAIL WIDTH) TERMINAL NOTES 1 MATERIAL 0.15 ±0.05 (FITTING NAIL WIDTH) HOUSING : LIQUID CRYSTAL POLYMER UL94V-0(COLOR : BLACK) TERMINAL : COPPER ALLOY FITTING NAIL : COPPER ALLOY 2 PLATING TERMINAL: CONTACT AREA : GOLD 0.1 μm MIN. TAIL AREA : GOLD 0.05 μm MIN. UNDER PLATING : NICKEL 1.0 μm MIN. *DIVIDE INTO PARTS THE GOLD PLATING OF THE CONTACT AND THE TAIL PART BY THE NICKEL PLATING. FITTING NAIL: CONTACT AREA : GOLD 0.1 μm MIN. TAIL AREA : GOLD 0.05 μm MIN. UNDER PLATING : NICKEL 1.0 μm MIN. *DIVIDE INTO PARTS THE GOLD PLATING OF THE CONTACT AND THE TAIL PART BY THE NICKEL PLATING. *EVEN THOUGH GOLD PLATING ON THE TOP SURFACE OF NAIL MIGHT BE THIN, NO FUNCTIONAL PROBLEM. 3 MATE WITH : 2153600064 4 TERMINAL AND FITTING NAIL COPLANARITY TO BE 0.08MAXIMUM. C B A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 9 2021/06/30 C 0.70 2.16 B A --2153610064 〇 EMBOSSED TAPE HIGH VOL. TOOL LOW VOL. TOOL PACKAGE SAMPLE PREPARATION ○:TOOLED ORDER No. △:WORK IN PROCESS ---:TOOLING TO BE CONFIRMED DIMENSION UNITS SCALE mm 10:1 6 SIGNAL B CIRCUIT CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.03 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 7 6 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 14:16:53 8 0.48 ±0.1 HOUSING 5 4 EC NO: 668673 DRWN: RMIYAMOTO CHK'D: KSASAKI APPR: YKOBAYASHI02 INITIAL REVISION: DRWN: RMIYAMOTO APPR: YKOBAYASHI02 THIRD ANGLE PROJECTION DRAWING 0.35BB CONN. H=0.6 5G15 (6+4P RF) PLUG 2021/06/30 2021/06/30 2021/06/30 2021/06/25 2021/06/30 SERIES A3-SIZE 215361 3 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2153611000-SD MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 000 A SHEET NUMBER 1 OF 2 1 A 10 9 7 8 5 6 4 3 2 1 CONFIDENTIAL F F B+1.4 ±0.03 �B� 0.42 ±0.02 (TERMINAL) (TERMINAL) (NAIL) �0.29� �0.33� (NAIL) B+0.28 MIN. 0.39 MIN. E D (NAIL) �0.24� (NAIL) �1.07� (NAIL) �0.29� (TERMINAL) �1.70� �0.20� (NAIL) �0.16� (NAIL) (PITCH) �0.24� (NAIL) �0.29� (NAIL) �1.07� �1.26� (NAIL) �0.20� 0.32 ±0.02 (TERMINAL) 1.67 ±0.02 �1.10� �0.35� (NAIL) 0.32 ±0.02 0.27 MIN. (NAIL) 0.27 ±0.02 (NAIL) D (NAIL) (TERMINAL) (NAIL) (NAIL) 0.27 ±0.02 0.18 ±0.02 1.10 ±0.02 (NAIL) 0.22 ±0.03 �0.42� �0.70� (TERMINAL) B ±0.03 (PITCH) 0.32 ±0.02 (NAIL) (NAIL) 1.24 ±0.02 E (B+1.40) 0.35 ±0.03 0.22 ±0.02 0.34 MIN. 0.70 ±0.02 B+1.62 MAX. B+0.36 MAX. 0.37 ±0.02 (NAIL) C C RECOMMENDED P.W.BOARD PATTERN LAYOUT (REFERENCE) RECOMMENDED METAL MASK LAYOUT (REFERENCE) SOLDERING PROHIBITED AREA WHEN WIRING IS LOCATED, THE WIRING MUST BE MASKED BY COVER LAY OR RESIST FILM. RECOMMENDED THICKNESS OF METAL MASK : t=0.08mm B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 20:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 9 2021/06/30 ± 3.0 ° 4 PLACES ± 0.03 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 14:16:53 8 ANGULAR TOL 7 6 5 4 EC NO: 668673 DRWN: RMIYAMOTO CHK'D: KSASAKI APPR: YKOBAYASHI02 INITIAL REVISION: DRWN: RMIYAMOTO APPR: YKOBAYASHI02 THIRD ANGLE PROJECTION DRAWING 0.35BB CONN. H=0.6 5G15 (6+4P RF) PLUG 2021/06/30 2021/06/30 2021/06/30 2021/06/25 2021/06/30 SERIES PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2153611000-SD MATERIAL NUMBER CUSTOMER A3-SIZE 215361 3 GENERAL 2 PSD 000 A SHEET NUMBER 2 OF 2 1 A