2188760064

10 9 7 8 F 5 6 4 3 PULL OUT DIRECTION E 100 MIN. TOP TAPE BONDED PART. (EMPTY) E TOP TAPE LEADER PART 400MIN. "D" F ⌀ 380 ±2 �⌀80� PULL OUT DIRECTION COMPONENT SUPPLIER TAIL PART (EMPTY) 160 MIN. D E ±1 4. PEELING OFF FORCE OF THE TOP TAPE IS DEFINED BY IEC60286-3. 5. MATERIAL CARRIER TAPE : POLYSTYRENE OR PET TOP TAPE : PET , OTHER REEL : POLYSTYRENE (PS) ＜RECYCLE MATERIAL CONTAINED＞ 6 CONFORM TO 2188769200-SPK/PS/200 FOR PACKAGING SPECIFICATION. 7 CONFORM TO 2188769200-SPK/PS/201 FOR PACKAGING SPECIFICATION. F ±1 C 1 NOTES 1. RE DETAILED DIMENSION, SEE PRODUCT DRAWING. 2. NUMBER OF CONNECTORS : 11000PCS/REEL 3. LEAD TAPE LENGTH. REEL D 2 C (⌀10) (120 °) (22) (2) B B (⌀21) (⌀13) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DETAIL "D" DOCUMENT STATUS P1 RELEASE DATE 9 2022/12/19 SCALE mm 1:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 DIMENSION UNITS ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:30:10 8 ANGULAR TOL 7 6 5 4 5G25 REC EMBOSS PACKAGE EC NO: 732080 DRWN: RAJMOK CHK'D: YNUKANOBU APPR: YNAITO INITIAL REVISION: DRWN: NKONDO APPR: KSASAKI THIRD ANGLE PROJECTION 2022/12/02 2022/12/15 2022/12/19 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/11/09 2022/09/14 DRAWING SERIES A3-SIZE 218876 3 2188760000-SD MATERIAL NUMBER CUSTOMER SEE SHEET-2 2 GENERAL PSD 000 B SHEET NUMBER 1 OF 2 1 A 10 9 7 8 5 6 4 3 2 1 F F PULL OUT DIRECTION 8 ±0.1 �3� B TOP TAPE 1.75 ±0.1 �1.05� A H ±0.05 0.3 ±0.05 SECTION B-B D (J) E G ±0.3 E B ⌀ 1.5 +0.1 0 D 4 ±0.1 A ACCUMULATIVE PITCH 40±0.2 C SECTION A-A B �0.75� 3 ±0.05 C 2188760064 2188760062 ORDER NO. ORDER NO. PACKAGING SPEC: 7 PACKAGING 6 SPEC: 7.5 4.4 16 21.4 17.4 J H G F E --〇 HIGH VOL. LOW VOL. TOOL TOOL SAMPLE PREPARATION ○：TOOLED △：WORK IN PROCESS ---：TOOLING TO BE CONFIRMED 6 Ckt. B CONNECTOR SERIES No: 218876**** THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/12/19 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:30:10 8 ANGULAR TOL 7 6 5 4 5G25 REC EMBOSS PACKAGE EC NO: 732080 DRWN: RAJMOK CHK'D: YNUKANOBU APPR: YNAITO INITIAL REVISION: DRWN: NKONDO APPR: KSASAKI THIRD ANGLE PROJECTION 2022/12/02 2022/12/15 2022/12/19 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/11/09 2022/09/14 DRAWING SERIES A3-SIZE 218876 3 2188760000-SD MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 000 B SHEET NUMBER 2 OF 2 1 A 10 9 7 8 5 6 4 3 2 1 NOTES 4.16 ±0.1 F 1. X SIGNAL TERMINAL : COPPER ALLOY 1.15 SHIELD : COPPER ALLOY GND COVER : COPPER ALLOY 2. 2.76 ±0.1 SHIELD RF TERMINAL : COPPER ALLOY (PICK UP AREA) 1.5 ±0.1 (PITCH) E F HOUSING : LIQUID CRYSTAL POLYMER UL94V-0(COLOR : BLACK) 0.7 ±0.1 0.35 MATERIAL PLATING SIGNAL TERMINAL E CONTACT AREA : GOLD TAIL AREA : GOLD GND COVER RF TERMINAL SIGNAL TERMINAL HOUSING UNDER : NICKEL RF TERMINAL CONTACT AREA : GOLD TAIL AREA : GOLD UNDER : NICKEL D D 0.6 ±0.1 SHIELD TAIL AREA : NICKEL (SOLDERABLE) GND COVER CONTACT AREA : GOLD TAIL AREA : GOLD UNDER : NICKEL (SIGNAL TERMINAL) 1.45 ±0.08 C 0.06 ±0.05 (GND COVER TAIL WIDTH) 9 CONFORM TO 2188769200-SPK/PS/201 FOR PACKAGING SPECIFICATION. EMBBOSED TAPE PACKAGE HIGH VOL. TOOL LOW VOL. TOOL ORDER No. ORDER No. PACKAGING SPEC: PACKAGING SPEC: 6 SIGNAL CIRCUIT SAMPLE PREPARATION ○：TOOLED △：WORK IN PROCESS ---：TOOLING TO BE CONFIRMED B 5 DIMENSION UNITS SCALE mm 10:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) ⌖ 0.15 X (SIGNAL TERMINAL TAIL WIDTH) 2022/12/19 6 EMBBOSED TAPE PACKAGE (GND COVER TAIL WIDTH) A RELEASE DATE CONFORM TO 2188769200-SPK/PS/200 FOR PACKAGING SPECIFICATION. --- (RF TERMINAL TAIL WIDTH) P1 5 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 0.14 ±0.05 DOCUMENT STATUS COPLANARITY TO BE 0.08MAXIMUM. 〇 6 FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 4. 2188760062 0.14 ±0.05 ⌖ 0.15 X MATE WITH :2188770062 2188760064 B 0.19 ±0.05 3. ± 3.0 ° 4 PLACES ± 0.03 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:30:15 8 ANGULAR TOL 7 6 5 4 5G25 REC ASSY EC NO: 732080 DRWN: RAJMOK CHK'D: YNUKANOBU APPR: YNAITO INITIAL REVISION: DRWN: NKONDO APPR: KSASAKI THIRD ANGLE PROJECTION 2022/12/02 2022/12/15 2022/12/19 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/11/09 2022/09/14 DRAWING SERIES A3-SIZE 218876 3 2188761000-SD MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 000 B SHEET NUMBER 1 OF 2 1 A 10 9 7 8 5 6 4 3 2 1 4.26 ±0.01 3.4 ±0.01 4.26 ±0.02 (SHIELD) 3.09 ±0.01 1.46 ±0.03 2.58 ±0.01 (GND COVER) 1.77 ±0.01 0.245 ±0.01 (GND COVER) 1.36 ±0.01 (GND COVER) (GND COVER) 0.77 ±0.01 1.07 ±0.01 1.69 ±0.01 0.18 ±0.01 0.18 ±0.02 0.20 ±0.02 0.17 ±0.01 0.21 ±0.01 (GND COVER) (SIGNAL) (SIGNAL) (RF) 0.16 ±0.01 0.16 ±0.01 (GND COVER) (GND COVER) P.W.BOARD PATTERN LAYOUT 0.35 ±0.02 1.15 ±0.02 (PITCH) (RF) SOLDERING PROHIBITED AREA WHEN WIRING IS LOCATED, THE WIRING MUST BE MASKED BY COVER LAY OR RESIST FILM. 0.7 ±0.03 (RF) (SIGNAL) 1.07 ±0.02 E D 0.29 ±0.01 (RF) 0.15 ±0.01 1.12 ±0.01 0.25 ±0.02 0.66 ±0.01 C 0.32 ±0.01 C 1.38 ±0.03 1.46 ±0.03 0.7 ±0.1 C 0.18 ±0.02 (GND COVER) (RF) 2.86 ±0.01 (GND COVER) 0.15 ±0.02 (GND COVER) 1.36 ±0.02 0.35 ±0.02 D 2 ±0.01 (PITCH) (SIGNAL) 0.29 ±0.02 0.35 ±0.02 0.96 ±0.01 0.24 ±0.01 C 0.30 ±0.03 0.20 ±0.01 (RF) 0.15 ±0.01 1.15 ±0.02 (GND COVER) 0.465 ±0.02 (GND COVER) 0.27 ±0.02 1.47 ±0.01 (SHIELD) 2.86 ±0.02 E (SHIELD) 0.27 ±0.02 0.7 ±0.03 (GND COVER) (GND COVER) 0.425 ±0.01 (SHIELD) 2.28 ±0.01 (SIGNAL) 1.38 ±0.03 0.19 ±0.01 0.27 ±0.02 F (SIGNAL) F METAL MASK LAYOUT B B THICKNESS OF METAL MASK : t=0.08mm THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A DOCUMENT STATUS P1 RELEASE DATE 9 2022/12/19 20:1 ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.03 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 03:30:15 8 SCALE mm 7 6 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) MATED CONDITION THIS DIMENSION SHOW A DIMENSION BETWEEN THE TAIL TO TAIL. FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 DIMENSION UNITS 5 4 5G25 REC ASSY EC NO: 732080 DRWN: RAJMOK CHK'D: YNUKANOBU APPR: YNAITO INITIAL REVISION: DRWN: NKONDO APPR: KSASAKI THIRD ANGLE PROJECTION 2022/12/02 2022/12/15 2022/12/19 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/11/09 2022/09/14 DRAWING SERIES A3-SIZE 218876 3 2188761000-SD MATERIAL NUMBER CUSTOMER SEE SHEET-1 2 GENERAL PSD 000 B SHEET NUMBER 2 OF 2 1 A