2451320220

5 6 4 3 2 1 REVISIONS DESCRIPTION DATE REV EC NO NA 2016/08/01 A INITIAL RELEASE CHANGER LH LIU D D 10.5 8.0 LENGTH SEE TABLE 21.5 C PIN 1 PIN 1 10.3 PIN 2 P2 P1 PIN 2 B A C FORMAT: tb-prod-A4 REVISION: G DATE: 2015/12/14 6 = 5 4 0 = 0 = 0 = 0 MICROFIT 2 CIRCUIT BLACK 5M OM MICROFIT 2 CIRCUIT BLACK 3M OM Microfit 2 Circuit Black 2M Overmolded Microfit 2 Circuit Black 1M Overmolded Microfit 2 Circuit Black 500MM OM TITLE 5000±50 3000±30 2000±20 1000±15 500±10 LENGTH C 2C*20AWG;UNSH;PVC;BK;OD=5.20MM;UL2464 B MicroFit 3.0 DR Rcpt 2Ckt A MicroFit 3.0 F Crp Term Chn Tin 20-24 ITEM DESCRIPTION B SEE TABLE L(MM) 2 4 Q'TY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2016/07/28 2016/08/14 2016/08/15 QUALITY SYMBOLS C 05:56:15 2451320250 2451320230 2451320220 2451320210 2451320205 PN WIRING CHART P1 WIRE COLOR P2 PIN 1 PIN 1 BLACK RED PIN 2 PIN 2 GENERAL TOLERANCES (UNLESS SPECIFIED) DIMENSION UNITS SCALE MM DRWN BY 1.5:1 DATE ANGULAR TOL ± 2.0 ° CHK'D BY 3 PLACES ± ± 0.25 1 PLACE ± 0.5 ± 2 PLACES = 0 = 0 0 PLACES = 0 = 0 A 2016/06/23 XJGUO01 ± 4 PLACES REV RELEASE STATUS P1 RELEASE DATE 16.08.2016 TABLE 107522 XJGUO01 LHLIU FNIE A NOTES: 1. MOLDING MATERIAL: 1.1 INNERMOLD AND STOPPER MOLD: PE RESIN. 1.2 OVERMOLD: BLACK PVC RESIN. 2. ELECTRICAL PERFORMANCE: 2.1 CURRENT RATING: 5.5 AMPS. (EACH APPLICATION SHOULD BE EVALUATED BY THE END USER FOR COMPLIANCETO SPECIFIC SAFETY AGENCY REQUIREMENTS. THE RATING IS PROVIDED AS REFERENCE. APPROPRIATE DE-RATING IS REQUIRED BASED ON AMBIENT CONDITIONS,COPPER TRACE SIZE ON THE PCB, GROSS HEATING FROM ADJACENT MODULES/COMPONENTS AND OTHER FACTORS THAT INFLUENCE CONNECTOR PERFORMANCE.) 2.2 VOLTAGE RATING: 300V AC. 2.3 THIS PRODUCT MUST PASS 100% CONTINUITY TEST PER MOLEX ES-000. 1) DIELECTRONIC STRENGTH: 500V DC/0.01 SEC. 2) INSULATION RESISTANCE: 20M OHMS. 3. MECHANICAL PERFORMANCE: 3.1 OVERMOLD SIDE CAN WITHSTAND 5KGF AXIAL TENSILE FORCE FOR ONE MINUTE WITHOUT PHYSICAL DAMAGE. 3.2 OVERMOLD SIDE CAN PASS THE BENDING TEST IN 100 CYCLES AT EACH OF 2 PLANES, PER EIA364-41 CONDITION I. 3.3 MINIMUM DYNAMIC BEND REDIUS: 50MM 3.4 MINIMUM STATIC BEND REDIUS: 25MM 4. TEMPERATURE: 4.1 OPERATING TEMPERATURE: -20 TO 80 C DEG. (INCLUDING T-RISE FROM APPLIED CURRENT) 5. ALL MATERIALS MUST MEET RoHS 2011/65/EU. EC NO: DRWN: CHK'D: APPR: B C LHLIU APPR BY SEE TABLE DATE 2016/07/27 DATE PRODUCT CUSTOMER DRAWING SERIES DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 3 DRAWING SIZE MATERIAL NUMBER CUSTOMER THIRD ANGLE PROJECTION 201440 A4 SEE TABLE DOCUMENT NUMBER 2014400085 2 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 000 1 1 OF 2 A