2451320405

5 6 4 3 2 1 REVISIONS DESCRIPTION DATE REV EC NO NA 2016/08/01 A INITIAL RELEASE D PIN 2 11.0 PIN 1 11.0 16.0 CHANGER LH LIU D LENGTH SEE TABLE 8.0 PIN 2 PIN 1 C P1 11.0 PIN 3 PIN 4 P2 PIN 4 PIN 3 B A C FORMAT: tb-prod-A4 REVISION: G DATE: 2015/12/14 6 WIRING CHART P1 WIRE COLOR P2 PIN 1 PIN 1 BROWN PIN 2 PIN 2 YELLOW WHITE PIN 3 PIN 3 PIN 4 PIN 4 GREEN = 5 4 = 0 = 0 = C 05:56:15 0 0 2016/07/31 2016/08/14 2016/08/15 QUALITY SYMBOLS MICROFIT 4 CIRCUIT BLACK 5M OM MICROFIT 4 CIRCUIT BLACK 3M OM Microfit 4 Circuit Black 2M Overmolded Microfit 4 Circuit Black 1M Overmolded Microfit 4 Circuit Black 500MM OM TITLE 5000±50 3000±30 2000±20 1000±15 500±10 LENGTH C 4CX20AWG;UNSH;PVC;BK;5.50MM;UL2464 B MicroFit 3.0 DR Rcpt 4Ckt A MicroFit 3.0 F Crp Term Chn Tin 20-24 ITEM DESCRIPTION B SEE TABLE 2 8 Q'TY L(MM) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) DIMENSION UNITS SCALE MM DRWN BY 1.5:1 DATE ANGULAR TOL ± 2.0 ° CHK'D BY 3 PLACES ± ± 0.25 1 PLACE ± 0.5 ± 2 PLACES = 0 = 0 0 PLACES = 0 = 0 A 2016/06/23 XJGUO01 ± 4 PLACES REV RELEASE STATUS P1 RELEASE DATE 16.08.2016 TABLE 2451320450 2451320430 2451320420 2451320410 2451320405 PN 107522 XJGUO01 LHLIU FNIE A NOTES: 1. MOLDING MATERIAL: 1.1 INNERMOLD AND STOPPER MOLD: PE RESIN. 1.2 OVERMOLD: BLACK PVC RESIN. 2. ELECTRICAL PERFORMANCE: 2.1 CURRENT RATING: 5 AMPS. (EACH APPLICATION SHOULD BE EVALUATED BY THE END USER FOR COMPLIANCETO SPECIFIC SAFETY AGENCY REQUIREMENTS. THE RATING IS PROVIDED AS REFERENCE. APPROPRIATE DE-RATING IS REQUIRED BASED ON AMBIENT CONDITIONS,COPPER TRACE SIZE ON THE PCB, GROSS HEATING FROM ADJACENT MODULES/COMPONENTS AND OTHER FACTORS THAT INFLUENCE CONNECTOR PERFORMANCE.) 2.2 VOLTAGE RATING: 300V AC. 2.3 THIS PRODUCT MUST PASS 100% CONTINUITY TEST PER MOLEX ES-000. 1) DIELECTRONIC STRENGTH: 500V DC/0.01 SEC. 2) INSULATION RESISTANCE: 20M OHMS. 3. MECHANICAL PERFORMANCE: 3.1 OVERMOLD SIDE CAN WITHSTAND 5KGF AXIAL TENSILE FORCE FOR ONE MINUTE WITHOUT PHYSICAL DAMAGE. 3.2 OVERMOLD SIDE CAN PASS THE BENDING TEST IN 100 CYCLES AT EACH OF 2 PLANES, PER EIA364-41 CONDITION I. 3.3 MINIMUM DYNAMIC BEND REDIUS: 55MM 3.4 MINIMUM STATIC BEND REDIUS: 25MM 4. TEMPERATURE: 4.1 OPERATING TEMPERATURE: -20 TO 80 C DEG. (INCLUDING T-RISE FROM APPLIED CURRENT) 5. ALL MATERIALS MUST MEET RoHS 2011/65/EU. EC NO: DRWN: CHK'D: APPR: B C LHLIU APPR BY SEE TABLE DATE 2016/07/27 DATE PRODUCT CUSTOMER DRAWING SERIES DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 3 DRAWING SIZE MATERIAL NUMBER CUSTOMER THIRD ANGLE PROJECTION 201440 A4 SEE TABLE DOCUMENT NUMBER 2014400088 2 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 000 1 1 OF 1 A