2451320810

5 6 4 3 2 1 REVISIONS D PIN 4 17.0 8.0 C P1 12.0 11.0 B PIN 8 20.0 CHANGER LH LIU LH LIU INITIAL RELEASE CHANGE RAW CABLE LENGTH SEE TABLE PIN 1 11.5 DESCRIPTION REV A B DATE 2016/08/01 2017/04/14 EC NO NA CY17-5287 PIN 4 PIN 1 PIN 8 PIN 5 D P1 A PIN 5 C FORMAT: tb-prod-A4 REVISION: G DATE: 2015/12/14 6 = C 4 0 = 0 = 0 = 10:17:10 5 2451320850 2451320830 2451320820 2451320810 2451320805 PN 0 MICROFIT 8 CIRCUIT BLACK 5M OM MICROFIT 8 CIRCUIT BLACK 3M OM Microfit 8 Circuit Black 2M OM Microfit 8 Circuit Black 1M OM Microfit 8 Circuit Black 500M OM TITLE 5000±50 3000±30 2000±20 1000±15 500+/-10 LENGTH C 8CX20AWG;UNSH;PVC;BK;7.0MM;UL2464 B MicroFit 3.0 DR Rcpt 8Ckt A MicroFit 3.0 F Crp Term Chn Tin 20-24 ITEM DESCRIPTION B SEE TABLE B L(MM) 2 16 Q'TY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2017/02/24 2017/04/14 2017/04/16 QUALITY SYMBOLS GENERAL TOLERANCES (UNLESS SPECIFIED) DIMENSION UNITS SCALE MM DRWN BY 1:1 DATE ANGULAR TOL ± 2.0 ° CHK'D BY 3 PLACES ± ± 0.25 1 PLACE ± 0.5 ± 2 PLACES = 0 = 0 0 PLACES = 0 = 0 B APPR BY FNIE DRAWING SIZE SEE TABLE DATE LHLIU DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 3 2016/06/27 XJGUO01 ± 4 PLACES REV RELEASE STATUS P1 RELEASE DATE 16.04.2017 TABLE WIRING CHART P1 WIRE COLOR P2 PIN 1 PIN 1 BLACK RED PIN 2 PIN 2 WHITE PIN 3 PIN 3 PIN 4 PIN 4 GREEN PIN 5 PIN 5 ORANGE BLUE PIN 6 PIN 6 PIN 7 PIN 7 YELLOW PIN 8 PIN 8 GRAY 115812 XJGUO01 LHLIU FNIE A NOTES: 1. MOLDING MATERIAL: 1.1 INNERMOLD AND STOPPER MOLD: PE RESIN. 1.2 OVERMOLD: BLACK PVC RESIN. 2. ELECTRICAL PERFORMANCE: 2.1 CURRENT RATING: 3.5 AMPS. (EACH APPLICATION SHOULD BE EVALUATED BY THE END USER FOR COMPLIANCETO SPECIFIC SAFETY AGENCY REQUIREMENTS. THE RATING IS PROVIDED AS REFERENCE. APPROPRIATE DE-RATING IS REQUIRED BASED ON AMBIENT CONDITIONS,COPPER TRACE SIZE ON THE PCB, GROSS HEATING FROM ADJACENT MODULES/COMPONENTS AND OTHER FACTORS THAT INFLUENCE CONNECTOR PERFORMANCE.) 2.2 VOLTAGE RATING: 300V AC. 2.3 THIS PRODUCT MUST PASS 100% CONTINUITY TEST PER MOLEX ES-000. 1) DIELECTRONIC STRENGTH: 500V DC/0.01 SEC. 2) INSULATION RESISTANCE: 20M OHMS. 3. MECHANICAL PERFORMANCE: 3.1 OVERMOLD SIDE CAN WITHSTAND 5KGF AXIAL TENSILE FORCE FOR ONE MINUTE WITHOUT PHYSICAL DAMAGE. 3.2 OVERMOLD SIDE CAN PASS THE BENDING TEST IN 100 CYCLES AT EACH OF 2 PLANES, PER EIA364-41 CONDITION I. 3.3 MINIMUM DYNAMIC BEND REDIUS: 70MM 3.4 MINIMUM STATIC BEND REDIUS: 35MM 4. TEMPERATURE: 4.1 OPERATING TEMPERATURE: -20 TO 80 C DEG. (INCLUDING T-RISE FROM APPLIED CURRENT) 5. ALL MATERIALS MUST MEET RoHS 2011/65/EU. EC NO: DRWN: CHK'D: APPR: B C 2016/07/28 DATE PRODUCT CUSTOMER DRAWING 2016/08/16 SERIES MATERIAL NUMBER CUSTOMER THIRD ANGLE PROJECTION 201440 A4 SEE TABLE DOCUMENT NUMBER 2014400096 2 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 000 1 1 OF 1 A