2451350205

5 6 4 3 2 1 REVISIONS DATE REV EC NO DESCRIPTION NA 2016/07/29 A INITIAL RELEASE CY17-5959 2017/06/15 B UPDATE CABLE DESCRIPTION AND WIRE COLOR, 5.70MM WAS 5.40MM CHANGER LH LIU LH Liu D D A B C PIN 2 P1 C 16.6 9.0 C LENGTH SEE TABLE FORMAT: tb-prod-A4 REVISION: G DATE: 2015/12/14 6 = 5 4 0 = 0 = 0 = 2000+/-20 1000+/-15 500+/-10 LENGTH C 2CX18AWG;UNSH;PVC;BK;5.70MM;UL2464 B B CRIMP REC HOUSING 555702R A MF PLUS HCS CRIMP TERM. FEM 18-20 GA TIN ITEM DESCRIPTION B SEE TABLE L(MM) 2 4 Q'TY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2017/06/14 2017/06/15 2017/06/16 QUALITY SYMBOLS C 00:55:24 WIRING CHART P2 WIRE COLOR PIN 1 BLACK YELLOW B PIN 2 P1 PIN 1 PIN 2 GENERAL TOLERANCES (UNLESS SPECIFIED) DIMENSION UNITS SCALE MM DRWN BY 1:1 DATE ANGULAR TOL ± 2.0 ° CHK'D BY 3 PLACES ± 2 PLACES ± 0.25 0 1 PLACE ± 0.5 = 0 0 PLACES ± = 0 = 0 B DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 3 APPR BY FNIE DRAWING SIZE SEE TABLE DATE LHLIU 0 = 2016/05/31 XJGUO01 ± 4 PLACES REV RELEASE STATUS P1 RELEASE DATE 16.06.2017 TABLE 2451350220 Minifit Jr 2 Circuit Black 2M OM 2451350210 Minifit Jr 2 Circuit Black 1M OM 2451350205 Minifit Jr  2 Circuit Black 500MM OM PN TITLE 118193 LHLIU LHLIU FNIE NOTES: 1. MOLDING MATERIAL: 1.1 INNERMOLD AND STOPPER MOLD: PE RESIN. 1.2 OVERMOLD: BLACK PVC RESIN 2. ELECTRICAL PERFORMANCE: 2.1 CURRENT RATING: 8 AMPS (EACH APPLICATION SHOULD BE EVALUATED BY THE END USER FOR COMPLIANCETO SPECIFIC SAFETY AGENCY REQUIREMENTS THE RATING IS PROVIDED AS REFERENCE. APPROPRIATE DE-RATING IS REQUIRED BASED ON AMBIENT CONDITIONS,COPPER TRACE SIZE ON THE PCB, GROSS HEATING FROM ADJACENT MODULES/COMPONENTS AND OTHER FACTORS THAT INFLUENCE CONNECTOR PERFORMANCE.) 2.2 VOLTAGE RATING: 300V AC 2.3 THIS PRODUCT MUST PASS 100% CONTINUITY TEST PER MOLEX ES-000 1) DIELECTRONIC STRENGTH: 500V DC/0.01 SEC 2) INSULATION RESISTANCE: 20M OHMS 3. MECHANICAL PERFORMANCE: 3.1 OVERMOLD SIDE CAN WITHSTAND 5KGF AXIAL TENSILE FORCE FOR ONE MINUTE WITHOUT PHYSICAL DAMAGE 3.2 OVERMOLD SIDE CAN PASS THE BENDING TEST IN 100 CYCLES AT EACH OF 2 PLANES, PER EIA364-41 CONDITION I 3.3 MINIMUM DYNAMIC BEND REDIUS: 55MM 3.4 MINIMUM STATIC BEND REDIUS: 25MM 4. TEMPERATURE: 4.1 OPERATING TEMPERATURE: -20 TO 80 C DEG (INCLUDING T-RISE FROM APPLIED CURRENT) 5. ALL MATERIALS MUST MEET RoHS 2011/65/EU. EC NO: DRWN: CHK'D: APPR: A P2 PIN 1 PIN 1 16.0 24.0 B PIN 2 13.0 2016/07/28 DATE PRODUCT CUSTOMER DRAWING 2016/08/16 SERIES MATERIAL NUMBER CUSTOMER THIRD ANGLE PROJECTION 201440 A4 SEE TABLE DOCUMENT NUMBER 2014400029 2 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 000 1 1 OF 1 A