2451351020

5 6 4 3 2 1 REVISIONS DATE REV EC NO DESCRIPTION NA 2016/09/23 A INITIAL RELEASE D 15.6 15.0 27.0 D LENGTH SEE TABLE 10.0 A B C PIN 6 PIN 1 P1 27.4 PIN 5 CHANGER LH LIU PIN 10 PIN 5 PIN 6 PIN 1 P2 PIN 10 C FORMAT: tb-prod-A4 REVISION: G DATE: 2015/12/14 6 = C 5 = 0 = 0 = 04:09:37 4 0 0 TABLE 2451351020 Minifit Jr 10 Circuit Black 2M OM 2451351010 Minifit Jr 10 Circuit Black 1M OM 2451351005 Minifit Jr 10 Circuit Black 500MM OM PN TITLE 2000+/-20 1000+/-15 500+/-10 LENGTH B C 10CX18AWG;UNSH;PVC;BK;9.50MM;UL2464 B NEW MINI FIT CONN HOUS 55710R A MF PLUS HCS CRIMP TERM. FEM 18-20 GA TIN ITEM DESCRIPTION SEE TABLE L(MM) 2 20 Q'TY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 2016/09/22 2016/09/29 2016/10/05 QUALITY SYMBOLS GENERAL TOLERANCES (UNLESS SPECIFIED) DIMENSION UNITS SCALE MM DRWN BY 1:1 DATE ANGULAR TOL ± 2.0 ° CHK'D BY 3 PLACES ± ± 0.25 1 PLACE ± 0.5 ± 2 PLACES = 0 = 0 0 PLACES = 0 = 0 A 2016/06/21 XJGUO01 ± 4 PLACES REV RELEASE STATUS P1 RELEASE DATE 06.10.2016 WIRING CHART P1 P2 WIRE COLOR PIN 1 PIN 1 BLACK RED PIN 2 PIN 2 WHITE PIN 3 PIN 3 PIN 4 PIN 4 GREEN PIN 5 PIN 5 ORANGE BLUE PIN 6 PIN 6 PIN 7 PIN 7 YELLOW PIN 8 PIN 8 GRAY PIN 9 PIN 9 BROWN PURPLE PIN 10 PIN 10 109041 XJGUO01 LHLIU FNIE A NOTES: 1. MOLDING MATERIAL: 1.1 INNERMOLD AND STOPPER MOLD: PE RESIN. 1.2 OVERMOLD: BLACK PVC RESIN. 2. ELECTRICAL PERFORMANCE: 2.1 CURRENT RATING: 5 AMPS. (EACH APPLICATION SHOULD BE EVALUATED BY THE END USER FOR COMPLIANCETO SPECIFIC SAFETY AGENCY REQUIREMENTS. THE RATING IS PROVIDED AS REFERENCE. APPROPRIATE DE-RATING IS REQUIRED BASED ON AMBIENT CONDITIONS,COPPER TRACE SIZE ON THE PCB, GROSS HEATING FROM ADJACENT MODULES/COMPONENTS AND OTHER FACTORS THAT INFLUENCE CONNECTOR PERFORMANCE.) 2.2 VOLTAGE RATING: 300V AC. 2.3 THIS PRODUCT MUST PASS 100% CONTINUITY TEST PER MOLEX ES-000. 1) DIELECTRONIC STRENGTH: 500V DC/0.01 SEC. 2) INSULATION RESISTANCE: 20M OHMS. 3. MECHANICAL PERFORMANCE: 3.1 OVERMOLD SIDE CAN WITHSTAND 5KGF AXIAL TENSILE FORCE FOR ONE MINUTE WITHOUT PHYSICAL DAMAGE. 3.2 OVERMOLD SIDE CAN PASS THE BENDING TEST IN 100 CYCLES AT EACH OF 2 PLANES, PER EIA364-41 CONDITION I. 3.3 MINIMUM DYNAMIC BEND REDIUS: 95MM 3.4 MINIMUM STATIC BEND REDIUS: 50MM 4. TEMPERATURE: 4.1 OPERATING TEMPERATURE: -20 TO 80 C DEG. (INCLUDING T-RISE FROM APPLIED CURRENT) 5. ALL MATERIALS MUST MEET RoHS 2011/65/EU. EC NO: DRWN: CHK'D: APPR: B C LHLIU APPR BY SEE TABLE DATE 2016/09/22 DATE PRODUCT CUSTOMER DRAWING SERIES DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 3 DRAWING SIZE MATERIAL NUMBER CUSTOMER THIRD ANGLE PROJECTION 201440 A4 SEE TABLE DOCUMENT NUMBER 2014400066 2 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 000 1 1 OF 1 A