334710401

19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 TABLE OF CONTENTS L SHEET NO. K L SHEET DESCRIPTION 1 NOTES 2 KEY CONFIGURATIONS 3 BLADE SEALED ASSEMBLY 4 SYSTEM PACKAGING 5 BOM NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-33472-100 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY CHECKING, CRIMPING, AND TROUBLESHOOTING. -DESIGNED TO MATE WITH RECEPTACLE SEALED ASSEMBLY SPECIFIED IN MOLEX DRAWING SD-33471-041. RECEPTACLE SEALED ASSEMBLY CONFIGURATION MUST CONTAIN A PLR WITH SHORTING BAR LIFTER. -FOR 1.5mm BLADE TERMINALS TO BE USED WITH THE SHORTING BAR CIRCUIT LOCATIONS SEE MOLEX DRAWING SD-31296-001. -SHORTING BAR TERMINALS TO BE USED WITH WIRE WITHIN DIAMETER RANGE OF 1.7mm TO 2.06mm. -FOR 1.5mm BLADE TERMINALS TO BE USED WITH THE NON-SHORTING BAR CIRCUIT LOCATIONS SEE MOLEX DRAWING SD-33000-001. -NON-SHORTING BAR TERMINALS TO BE USED WITH WIRE WITHIN DIAMETER RANGE OF 1.2mm TO 2.69mm. -ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION -IN THE EVENT THAT THE PLR IS FOUND IN THE SEATED (FINAL LOCK) POSITION, REFER TO MOLEX SPECIFICATION PS-34646-001, AVAILABLE AT www.molex.com -ASSEMBLY CONFORMS TO SAE/USCAR-2 REV.4 WITH THE FOLLOWING EXCEPTIONS: TERMINAL INSERTION FORCE FOR WIRE DIAMETER ABOVE 2.5mm NOT EXCEEDING 2.69mm SHALL NOT EXCEED 45 NEWTONS. b. PRODUCT SPECIFICATION SEE: PS-33471-000 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY), AND PRODUCT VALIDATION. c. PACKAGING SPECIFICATION PER MOLEX DRAWING: PK-31300-635 d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR PRODUCTS AND PACKAGING SPECIFICATION: ES-40000-5016 e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) f. FOR INFORMATION ON 1X4 BLADE SEALED ASSEMBLY WITHOUT SHORTING BAR SEE SD-33481-041. J GROMMET CAP FOR OPTIONS SEE BOM H MAT SEAL OPTIONAL SEE BOM G CONNECTOR HOUSING K J H G 2. DESIGN - MATERIALS: a. CONNECTOR HOUSING, GROMMET CAP, PLR: SPS/NYLON BLEND 20% GLASS FILLED b. MAT SEAL: INHERENTLY LUBRICATED SILICONE c. SHORTING BARS: STAINLESS STEEL FOR OPTIIONS SEE BOM 3. DESIGN - GEOMETRY: a. THIS IS A 100% CAD GENERATED PART. THE CAD MATHEMATICAL DATA IS THE MASTER FOR THIS PART. FOR DIMENSIONAL OR ANY INFORMATION NOT SHOWN ON THIS DRAWING, ANALYZE THE CAD MODEL. b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M - 1994 c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715 d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX. e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD. THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION, AND CUSTOMER MATERIAL NUMBER. f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B) g. LASER MARKING: TBD F SHORTING BAR FOR OPTIONS SEE BOM F E E PRIMARY LOCK REINFORCEMENT (PLR) D D K2 K J H G F1 F REV C ADDED NEW P/N 31280-4436 TO 31280-4451 ADDED NEW P/N 31280-0450 31280-0451 ADDED NEW P/N 31280-0449 ADDED NEW P/N 31280-0448 UPDATED GROMMET CAP UPDATED DIMENSIONS TO MATCH MODEL REDRAWN DESCRIPTION C RELEASE STATUS 19 FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 P1 RELEASE DATE 18 31.10.2017 17 21:13:47 C 16 15 14 13 12 11 10 9 8 7 = 0 = 0 = 0 = 0 = 0 = 0 2017/10/31 0 DRWN BY ANGULAR TOL ± 1.0 ° K2 REV A = EC NO: 167392 DRWN: LSONG05 CHK'D: APPR: MVANSLAMBROU B 2017/10/30 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES mm 3:1 = 0 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DATE APPR BY VKOSHY DRAWING SIZE DATE 2012/09/04 THIRD ANGLE PROJECTION D 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL, SHORTING BAR 2013/03/22 MDICK DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 2012/08/28 KCUNNINGHAM CHK'D BY B DATE PRODUCT CUSTOMER DRAWING MATERIAL NUMBER SERIES 31280 SEE BOM DOCUMENT NUMBER 4 CUSTOMER SD-31280-200 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 001 1 OF 5 1 A 19 L 18 17 60° 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 KEY CONFIGURATIONS 60° K L K KEY A J J 30° 60° H H G G KEY B F F 30° 60° E E D D KEY C C 30° C 30° A RELEASE STATUS 19 FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 P1 RELEASE DATE 18 31.10.2017 17 21:13:47 C 16 15 14 13 12 11 10 9 8 7 = 0 = 0 = 0 = 0 = 0 = 0 2017/10/31 0 DRWN BY ANGULAR TOL ± 1.0 ° K2 REV KEY D = EC NO: 167392 DRWN: LSONG05 CHK'D: APPR: MVANSLAMBROU B 2017/10/30 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES mm 4:1 = 0 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DATE APPR BY VKOSHY DRAWING SIZE DATE 2012/09/04 THIRD ANGLE PROJECTION D 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL, SHORTING BAR 2013/03/22 MDICK DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 2012/08/28 KCUNNINGHAM CHK'D BY B DATE PRODUCT CUSTOMER DRAWING MATERIAL NUMBER SERIES 31280 SEE BOM DOCUMENT NUMBER 4 CUSTOMER SD-31280-200 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 001 2 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 ⌀25.27 L MIN PASS-THRU L OPTIONAL LASER MARKING THIS SURFACE SEE NOTE 3g. Y Z K K 17.13+0.10 -0.25 X X J Y TERMINAL A POSITION 4 55.85±0.60 3X 3.50 TERMINAL Z J POSITION 1 REAR VIEW 22.44±0.20 (WIRE HARNESS SIDE) H H G G 11.00 F F 2.00 15.00 6.60 E E SECTIONX-X SCALE 4:1 D D (18.00) C C PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN PRE-STAGED POSITION IN FINAL-LOCK POSITION SECTION Y-Y SECTION Z-Z A RELEASE STATUS 19 FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 P1 RELEASE DATE 18 31.10.2017 17 21:13:47 C 16 15 14 13 12 11 10 9 8 7 = 0 = 0 = 0 = 0 = 0 = 0 2017/10/31 0 DRWN BY ANGULAR TOL ± 1.0 ° K2 REV PRIMARY LOCK REINFORCEMENT (PLR) SHOWN = EC NO: 167392 DRWN: LSONG05 CHK'D: APPR: MVANSLAMBROU B 2017/10/30 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES mm 4:1 = 0 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DATE APPR BY VKOSHY DRAWING SIZE DATE 2012/09/04 THIRD ANGLE PROJECTION D 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL, SHORTING BAR 2013/03/22 MDICK DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 2012/08/28 KCUNNINGHAM CHK'D BY B DATE PRODUCT CUSTOMER DRAWING MATERIAL NUMBER SERIES 31280 SEE BOM DOCUMENT NUMBER 4 CUSTOMER SD-31280-200 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 001 3 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 L L K K ⌀A MIN PASS-THRU WITH NO CLEARANCE (74.70) OVERALL MATED SYSTEM J J H H G G F F E E CHARTED DIMENSIONS CONFIGURATION A MX150 1X4 RECPT SEALED ASSY - STANDARD 29.14 MX150 1X4 RECPT SEALED ASSY - ERGO 29.33 MX150 1X4 RECPT SEALED ASSY - SHORTING (SHRT) BAR 29.14 D D C C RELEASE STATUS 19 FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 P1 RELEASE DATE 18 31.10.2017 17 21:13:47 C 16 15 14 13 12 11 10 9 8 7 = 0 = 0 = 0 = 0 = 0 = 0 2017/10/31 0 DRWN BY ANGULAR TOL ± 1.0 ° K2 REV A = EC NO: 167392 DRWN: LSONG05 CHK'D: APPR: MVANSLAMBROU B 2017/10/30 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES mm 4:1 = 0 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DATE APPR BY VKOSHY DRAWING SIZE DATE 2012/09/04 THIRD ANGLE PROJECTION D 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL, SHORTING BAR 2013/03/22 MDICK DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 2012/08/28 KCUNNINGHAM CHK'D BY B DATE PRODUCT CUSTOMER DRAWING MATERIAL NUMBER SERIES 31280 SEE BOM DOCUMENT NUMBER 4 CUSTOMER SD-31280-200 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 001 4 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 L 1 BOM SHEET 1 K J H CAVITY NUMBER "X" INDICATES PLUGGED POSITION NUMBER OF PLUGGED POSITIONS MAT SEAL A 0 PRESENT PRESENT LIGHT GRAY B 0 PRESENT 31280-0438 BROWN C 0 31280-0439 GREEN D 31280-0440 CUSTOM TBD 31280-0441 BLACK A 31280-0442 BLACK 31280-0443 MOLEX ASSEMBLY PART NUMBER HOUSING COLOR 31280-0436 BLACK 31280-0437 CAVITY NUMBER "X" INDICATES PLUGGED POSITION K NUMBER OF PLUGGED POSITIONS MAT SEAL SHORTING BAR CIRCUITS 1&2 SHORTING BAR CIRCUITS 3&4 A 0 PRESENT PRESENT PRESENT LIGHT GRAY B 0 PRESENT PRESENT PRESENT 31280-4438 PRESENT BROWN C 0 PRESENT PRESENT PRESENT 31280-4439 PRESENT PRESENT GREEN D 0 PRESENT PRESENT PRESENT 31280-4440 PRESENT PRESENT NONE CUSTOM TBD 0 PRESENT PRESENT PRESENT 31280-4441 0 NONE PRESENT PRESENT BLACK A 2 PRESENT PRESENT NONE 31280-4442 B 0 NONE PRESENT PRESENT BLACK A 0 NONE PRESENT PRESENT 31280-4443 0 NONE PRESENT PRESENT B 0 NONE PRESENT PRESENT BROWN C LIGHT GRAY 31280-4444 31280-0445 D 0 NONE PRESENT PRESENT C 0 NONE PRESENT PRESENT GREEN 31280-4445 BROWN D 0 NONE PRESENT PRESENT 31280-0446 A 0 B NONE NONE PRESENT 31280-4446 0 PRESENT PRESENT PRESENT 31280-0447 BLACK LIGHT GRAY GREEN A 0 B 0 PRESENT PRESENT PRESENT 31280-4447 BLACK LIGHT GRAY NONE NONE PRESENT 31280-0448 YELLOW A 0 PRESENT PRESENT PRESENT 31280-4448 YELLOW A 0 PRESENT PRESENT PRESENT 31280-0449 YELLOW A 1 PRESENT PRESENT NONE 31280-4449 YELLOW A 1 PRESENT PRESENT NONE 31280-0450 DARK GRAY C 0 PRESENT PRESENT PRESENT 31280-4450 31280-0451 STONE GRAY D 0 PRESENT PRESENT PRESENT DARK GRAY C 0 PRESENT PRESENT PRESENT 31280-4451 STONE GRAY D 0 PRESENT PRESENT PRESENT MOLEX ASSEMBLY PART NUMBER HOUSING COLOR PRESENT 31280-4436 PRESENT PRESENT BLACK 31280-4437 PRESENT PRESENT PRESENT 0 PRESENT PRESENT 0 PRESENT 2 A LIGHT GRAY 31280-0444 KEYING OPTION 1 2 3 X 4 X X SHORTING BAR CIRCUITS 1&2 SHORTING BAR CIRCUITS 3&4 K2 KEYING OPTION 1 3 2 4 X X X L J H G G F F E E D D C C RELEASE STATUS 19 FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 P1 RELEASE DATE 18 31.10.2017 17 21:13:47 C 16 15 14 13 12 11 10 9 8 7 = 0 = 0 = 0 = 0 = 0 = 0 2017/10/31 0 DRWN BY ANGULAR TOL ± 1.0 ° K2 REV A = EC NO: 167392 DRWN: LSONG05 CHK'D: APPR: MVANSLAMBROU B 2017/10/30 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES mm 1:1 = 0 (UNLESS SPECIFIED) 4 PLACES ± 3 PLACES ± 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DATE APPR BY VKOSHY DRAWING SIZE DATE 2012/09/04 THIRD ANGLE PROJECTION D 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL, SHORTING BAR 2013/03/22 MDICK DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 2012/08/28 KCUNNINGHAM CHK'D BY B DATE PRODUCT CUSTOMER DRAWING MATERIAL NUMBER SERIES 31280 SEE BOM DOCUMENT NUMBER 4 CUSTOMER SD-31280-200 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 001 5 OF 5 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M TABLE OF CONTENTS L SHEET NO. SHEET DESCRIPTION 1 NOTES AND BOM 2 CONFIGURATIONS 3-4 K DESCRIPTION 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-33472-100 RECEPTACLE CONNECTOR ASSEMBLY 6 BACKSHELL NOTES 7 BACKSHELL 8 BACKSHELL CONFIGURATIONS MATING INTERFACE/CONNECTOR DRAWINGS DESCRIPTION DRAWING NO. MOLEX INLINE INTERFACE DEFINITION 1X2 PK-31300-635 1X2 *150-S-002-1-Z05 SD-33481-0001 1X6 PK-31300-903 1X6 *150-S-006-1-Z03 SD-33481-0001 L -CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR KEY CONFIGURATIONS 5 PACKAGING NOTES: VALID UNLESS OTHERWISE SPECIFIED MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY CHECKING, CRIMPING, AND TROUBLESHOOTING. -DESIGNED TO MATE WITH DEVICE OR CONNECTOR AS SPECIFIED IN THE MATING INTERFACE/CONNECTOR DRAWINGS CHART. *DENOTES DRAWINGS THAT CAN BE ACCESSED AT . K -ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION (SEE PLR PRE-LOCK VIEW SHEET 5). b. PRODUCT SPECIFICATION SEE: -STANDARD CONFIGURATION: PS-33471-000 -UL V0 CONFIGURATION: PS-160105-0001 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY), J J TERMINALS, WIRE DIAMETER RANGE, PRODUCT VALIDATION, AND PRODUCT DEVIATIONS. c. PACKAGING SPECIFICATION PER MOLEX DRAWING: SEE PACKAGING CHART d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR PRODUCTS AND PACKAGING SPECIFICATION: QEHS-699000-301 e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) H H 2. DESIGN - MATERIALS: 1x2 a. FOR BILL OF MATERIALS SEE: -STANDARD CONFIGURATION SD-33471-0002 -UL V0 CONFIGURATION SD-160105-0002 3. DESIGN - GEOMETRY: a. THE 3-D CAD DATA IS BASIC (WITHOUT TOLERANCE) AND MASTER FOR THIS PART WITH THE EXCEPTION OF UNDERLINED DIMENSIONS. DIMENSIONAL INFORMATION NOT SHOWN G G ON THIS DRAWING IS DEFINED BY THE DATA FILE AT ITS LATEST REVISION. b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M-2009 c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715 d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX. e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD. THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION, AND CUSTOMER MATERIAL NUMBER. F F f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B). g. LASER MARKING: 1. PART NUMBER 2. DAY OF THE YEAR 3. SHIFT 4. YEAR FOR ADDITIONAL INFORMATION SEE SECTION 5 UNDER PROCEDURES IN ES-34735-008. E E D A1 A 2 UPDATE VIEWSETS LAST NUMBER: 11 1 INITIAL RELEASE REV REV DESCRIPTION REMOVED: C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = B 1x6 DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 0 mm 1.5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 ANGULAR TOL = A MINOR GEOMETRY CHANGE FOR UL V0 INSPECTION NUMBER LOG ADDED: 11 D UPDATED THE DRAWING FRAME 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSHI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 1 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M SHEET DESCRIPTION CONFIGURATIONS L L K K J J 1x2 - STD 1x2 - UL V0* H H G G F F E E D C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = B 1x6 - STD DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 1x6 - UL V0* RELEASE DATE 18 2020/08/26 17 0 mm 1.5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 ANGULAR TOL = A D *MINOR GEOMETRY DIFFERENCE THAN STANDARD CONFIGUATION SEE NOTES 1 & 2 FOR MORE INFORMATION 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 2 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 SHEET DESCRIPTION M M KEY CONFIGURATIONS 1X2 L L 60° 60° K K KEY A J 35° 60° J H H KEY B 35° 60° G G F F KEY C 35° 35° E E D D KEY D C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 3:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 mm ANGULAR TOL = B 0 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 3 OF 8 1 A 20 M 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M SHEET DESCRIPTION 1X6 KEY CONFIGURATIONS CONT. L L 60° 60° K K KEY A J J 30° 60° H H KEY B G G 30° 60° F F KEY C E E 30° 30° D D KEY D C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 3:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 mm ANGULAR TOL = B 0 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 4 OF 8 1 A 20 M 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 CHARTED DIMENSIONS SHEET DESCRIPTION DIMENSIONS DESCRIPTION RECEPTACLE CONNECTOR ASSEMBLY - STD M A 1X2 19.40 B C D E F 1.75 21.73 20.55 37.65 19.64 L L 1X6 32.75 1.75 35.21 19.90 37.65 N/A N/A 1.75 35.23 19.90 37.65 33.64 1X6 UL V0 *DIM F MAX. *APPLIE TO UL V0 CONFIGURATIONS ONLY K ⌀DIM C MIN PASS-THRU WITH NO CLEARANCE 11 LASER MARKING ON THIS SURFACE TERMINAL Z SEE NOTE 3g. K 2 POSITION 1 X J DIM D MAX J 3 H H 3.50 TYP Z LAST 4X DIM B DIM E MAX X 1 DIM A MAX 5 G TERMINAL POSITION G REAR VIEW (WIRE HARNESS SIDE) MOLD CAVITY I.D. F THIS LOCATION F RECYCLE CODE THIS LOCATION MANUFACTURING LOCATION CODE THIS LOCATION E E D D 2.75±0.50 6 C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = PRIMARY LOCK REINFORCEMENT (PLR) SHOWN PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN PRE-STAGED POSITION IN FINAL-LOCK POSITION SECTION Z-Z A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 SECTION X-X 2020/08/26 17 15 14 13 3:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 mm ANGULAR TOL = B 0 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 5 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M SHEET DESCRIPTION BACKSHELL NOTES L L BACKSHELL NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-34951-001 -DESIGNED TO MATE WITH RECEPTACLE SEALED ASSEMBLY SPECIFIED IN MOLEX DRAWING SD-33471-0001. -SYSTEM TO BE USED WITH WIRE WITHIN DIAMETER RANGE OF 1.2mm TO 2.69mm. K K -COMPONENTS ARE OPTIONAL AND MUST BE PURCHASED SEPERATELY. -BACKSHELL DESIGN IS OWNED BY SCHLEMMER. -FOR ADDITIONAL INFORMATION SEE THE BACKSHELL COMPONENT DRAWING SD-34949-0001. J J BACKSHELL (BKS) BACKSHELL CUSTOMER MODEL NUMBER LEGEND 34949-XXXX H H CUSTOMER MODEL COMPONENTS 0 - BACKSHELL ONLY 1 - BACKSHELL & MX150 HOUSING KEY A ASSEMBLY 2 - BACKSHELL & MX150 HOUSING KEY B ASSEMBLY 3 - BACKSHELL & MX150 HOUSING KEY C ASSEMBLY 4 - BACKSHELL & MX150 HOUSING KEY D ASSEMBLY 1X2 BACKSHELL FEATURES 1 - WITH RIBS 2 - WITHOUT RIBS G RECEPTACLE SEALED ASSEMBLY G MX150 CIRCUIT SIZE 02, 03, 04, 05, 06 F F E E D D C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 mm ANGULAR TOL = B 0 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 6 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M SHEET DESCRIPTION BACKSHELL L L W K K J J W H H G G 11.00 1.50 F F 10.70 6.50 E E Partial W-W SCALE 4:1 D D C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 mm ANGULAR TOL = B 0 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 7 OF 8 1 A 20 M 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M SHEET DESCRIPTION CHARTED DIMENSIONS BACKSHELL CONFIGURATIONS DESCRIPTION DIMENSIONS 1X2 G 26.00 L L K K J J (71.20) ⌀DIM G MIN PASS-THRU WITH NO CLEARANCE H H G G F F E E RECEPTACLE SEALED ASSEMBLY WITH RECEPTACLE BACKSHELL D D C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 1.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.2 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:52 16 0 mm ANGULAR TOL = B 0 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: APROFFITT APPR: KDEKOSKI THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2015/11/04 2016/06/14 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-0001 MATERIAL NUMBER PSD 001 GENERAL MARKET 3 A1 SHEET NUMBER CUSTOMER SEE NOTE 2a 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 RCPT SINGLE ROW SEALED ASSY MAT SEAL 2 8 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M TABLE OF CONTENTS CPA OPTIONAL GROMMET CAP, STANDARD (GC) SEE BOM FOR OPTIONS SEE BOM SHEET NO. SHEET DESCRIPTION 1 NOTES 2 KEY CONFIGURATIONS 3 RECEPTACLE SEALED ASSEMBLY L BOM 4-5 CONNECTOR HOUSING L FOR OPTIONS SEE BOM MAT SEAL OPTIONAL K K SEE BOM NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-33472-100 -CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY CHECKING, CRIMPING, AND TROUBLESHOOTING. -STANDARD (NON-SHRT) CONFIGURATIONS DESIGNED TO MATE WITH DEVICE CONNECTION AS SPECIFIED IN DRAWING SD-33481-041 AND EWCAP 150-S-004-1-Z03, AVAILIBLE AT http://ewcap.uscarteams.org/ -SHORTING BAR CONFIGURATIONS DESIGNED TO MATE WITH BLADE SEALED ASSEMBLY SPECIFIED IN DRAWING SD-31280-200 -FOR 1.5mm RECEPTACLE TERMINALS TO BE USED WITH THIS ASSEMBLY. SEE MOLEX DRAWING SD-33012-002. -SYSTEM TO BE USED WITH WIRE WITHIN DIAMETER RANGE OF 1.2mm TO 2.69mm. -ASSEMBLY SHIPPED WITH PLR AND CPA IN PRE-LOCK POSITION (SEE SECTION Z-Z PRE-LOCK). -IN THE EVENT THAT THE PLR IS FOUND IN THE SEATED (FINAL LOCK) POSITION, REFER TO MOLEX SPECIFICATION PS-34646-001, AVAILABLE AT www.molex.com . -ASSEMBLY CONFORMS TO SAE/USCAR-2 REV 4 WITH THE FOLLOWING EXCEPTIONS: ENGAGEMENT FORCE TO MOVE CPA FROM PRE-LOCK TO FINAL LOCK POSITION WHEN UNMATED: 40N MIN. DISENGAGEMENT FORCE TO MOVE CPA FROM FINAL LOCK TO PRE-LOCK POSITION: 3N MIN, 40N MAX. TERMINAL INSERTION FORCE FOR WIRE DIAMETER ABOVE 2.5mm AND NOT EXCEEDING 2.69mm SHALL NOT EXCEED 40 NEWTONS. b. PRODUCT SPECIFICATION SEE: PS-33471-000 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY), AND PRODUCT VALIDATION. c. PACKAGING SPECIFICATION PER MOLEX DRAWING: PK-31300-903 d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR PRODUCTS AND PACKAGING SPECIFICATION: ES-40000-5016 e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) PRIMARY LOCK REINFORCEMENT (PLR) FOR OPTIONS SEE BOM J RING SEAL MX150 1X4 RECEPTACLE SEALED ASSEMBLY - STANDARD (STD) H ERGONOMIC GROMMET CAP (GCE) FOR OPTIONS SEE BOM G F J H G F 2. DESIGN - MATERIALS: a. SEE BOM TABLE E 3. DESIGN - GEOMETRY: a. THIS IS A 100% CAD GENERATED PART. THE CAD MATHEMATICAL DATA IS THE MASTER FOR THIS PART. FOR DIMENSIONAL OR ANY INFORMATION NOT SHOWN ON THIS DRAWING, ANALYZE THE CAD MODEL. b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M - 1994 c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715 d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX. e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD. THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION, AND CUSTOMER MATERIAL NUMBER. f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B) g. LASER MARKING: TBD MX150 1X4 RECEPTACLE SEALED ASSEMBLY - ERGO UNLESS COMPONENT NOTED, SEE STANDARD ASSEMBLY E D D INSPECTION NUMBER LOG LAST NUMBER USED: 5 ADDED: REMOVED: 2 PRIMARY LOCK REINFORCEMENT WITH SHORTING BAR LIFTER (PLR W/ SHORTING BAR) FOR OPTIONS SEE BOM C = B MX150 1X4 RECEPTACLE SEALED ASSEMBLY - SHORTING (SHRT) BAR UNLESS COMPONENT NOTED, SEE STANDARD ASSEMBLY FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 15 14 13 0 mm 12 ADD NEW P/N 33471-0493 REMOVE THE 33471-0489 CPA DESCRIPTION W REV 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 3.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:56 16 0 ANGULAR TOL = DOCUMENT STATUS UPDATED THE DRAWING FRAME ADD NEW P/N 33471-0494 FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = A W3 W2 W1 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: VKOSHY THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2010/03/31 2010/04/06 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-041 MATERIAL NUMBER PSD 002 GENERAL MARKET 3 W3 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X4 RECEPTACLE SEALED ASSEMBLY MAT SEAL 2 1 OF 6 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M KEY CONFIGURATIONS 60° 60° L L K K KEY A J J 30° 60° H H G G KEY B 30° 60° F F E E KEY C D D 30° 30° C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = KEY D A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 3.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:56 16 0 mm ANGULAR TOL = B 0 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: VKOSHY THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2010/03/31 2010/04/06 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-041 MATERIAL NUMBER PSD 002 GENERAL MARKET 3 W3 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X4 RECEPTACLE SEALED ASSEMBLY MAT SEAL 2 2 OF 6 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M RECEPTACLE SEALED ASSEMBLY L LASER MARKING ON THIS SURFACE Z SEE NOTE g. L ⌀B Y MIN PASS-THRU WITH NO CLEARANCE K K 19.80+0.10 -0.35 3 J J Y TERMINAL POSITION 1 Z TERMINAL POSITION 4 A 3X3.50 25.65+0.10 -0.40 4 H H MOLD CAVITY CODE G G RECYCLE CODE LOCATION CODE F F E E CIRCUIT ID D D 1 CHARTED DIMENSIONS 2.75±0.50 A CONFIGURATION MX150 1X4 RECPT SEALED ASSY - STANDARD 36.95 ±0.70 29.14 MX150 1X4 RECPT SEALED ASSY - ERGO 36.95 ±0.90 29.33 36.95 ±0.70 29.14 MX150 1X4 RECPT SEALED ASSY - SHORTING (SHRT) BAR C FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = B PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN PRE-STAGED POSITION PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN FINAL-LOCK POSITION SECTION Y-Y SECTION Z-Z DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 RELEASE DATE 18 2020/08/26 17 0 mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 3.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:56 16 0 ANGULAR TOL = A B 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: VKOSHY THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2010/03/31 2010/04/06 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-041 MATERIAL NUMBER PSD 002 GENERAL MARKET 3 W3 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X4 RECEPTACLE SEALED ASSEMBLY MAT SEAL 2 3 OF 6 1 A 20 19 18 17 16 15 33471-0440 33471-0439 33471-0438 33471-0437 33471-0436 33471-0435 33471-0434 33471-0433 33471-0432 33471-0431 33471-0430 33471-0429 VOID KEY KEY D W/ SHRT. BAR, GREEN KEY C W/ SHRT. BAR, BROWN KEY B W/ SHRT. BAR, LT. GRAY KEY A W/ SHRT. BAR, BLACK VOID KEY KEY D W/O MAT SEAL, GREEN KEY C W/O MAT SEAL, BROWN KEY B W/O MAT SEAL, LT. GRAY KEY A W/O MAT SEAL, BLACK VOID KEY KEY D W/ CPA, GREEN KEY C W/ CPA, BROWN KEY B W/ CPA, LT. GRAY KEY A W/ CPA, BLACK VOID KEY KEY D, GREEN KEY C, BROWN KEY B, LT. GRAY KEY A, BLACK M L K J H G 14 VOID KEY KEY D W/ CPA, GREEN KEY C W/ CPA, BROWN KEY B W/ CPA, LT. GRAY KEY A W/ CPA, BLACK VOID KEY KEY D, GREEN KEY C, BROWN KEY B, LT. GRAY KEY A, BLACK KEY C W/ CPA, BLACK 33471-0428 33471-0427 33471-0426 33471-0425 33471-0424 33471-0423 33471-0422 33471-0421 33471-0420 33471-0419 33471-0418 33471-0417 33471-0416 33471-0415 33471-0414 33471-0413 33471-0412 33471-0411 33471-0410 KEY D W/ CPA, GREEN KEY C W/ CPA, BROWN KEY B W/ CPA, LT. GRAY KEY A W/ CPA, BLACK VOID KEY KEY D, GREEN KEY C, BROWN KEY B, LT. GRAY KEY A, BLACK 33471-0409 33471-0408 33471-0407 33471-0406 33471-0405 33471-0404 33471-0403 33471-0402 33471-0401 ASSEMBLY PART NUMBER ASSEMBLY DESCRIPTION F 13 12 GCO GCO GCO GCO D C B A C B A CPA CPA CPA CPA 4 4 4 4 NOT RECOMMENDED NOT RECOMMENDED M M M M M CPA 4 4 4 4 NOT RECOMMENDED NOT RECOMMENDED GCO P P P P P GCO GCO GCO GCO P P P P M M M M CPA CPA CPA CPA NOT RECOMMENDED NOT RECOMMENDED P P P P P PS M M M M M CPA NOT RECOMMENDED NOT RECOMMENDED B A D C B A D C B A A A D B B C D C C GCP GCP GCP P P P M M M M GCP GCP GCP GCP P P P P M M M M GCP GCP GCP GCP P P P P M M M M GCP GCP GCP GCP GCO GCO GCO GCO D GCO GCP GCEO GCEP TABLE LEGEND D C COMPONENT A HOUSING KEY A B HOUSING KEY B C HOUSING KEY C D HOUSING KEY D GCO GROMMET CAP, STANDARD, OPEN GCP GROMMET CAP, STANDARD, PLUGGED GCEO GROMMET CAP, ERGONOMIC, OPEN GCEP GROMMET CAP, ERGONOMIC, PLUGGED M MAT SEAL P PLR, STANDARD R B A FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 18 2020/08/26 17 1 M BOM SHEET 1 L SALEABLE SEE P/N 33471-0475 SEE P/N 33471-0474 NOT RECOMMENDED SALEABLE J SEE P/N 33471-0473 SEE P/N 33471-0472 SALEABLE SEE P/N 33471-0471 SEE P/N 33471-0470 H SALEABLE SEE P/N 33471-0465 SEE P/N 33471-0464 SALEABLE G SEE P/N 33471-0463 SEE P/N 33471-0462 SALEABLE 2 1 3 4 BLOCKED TERMINAL COMMENTS STATUS F RING SEAL BURNT ORANGE INHERENTLY LUBRICATED SILICONE CPA BRIGHT RED PBT GF30 MAT SEAL LIGHT BLUE INHERENTLY LUBRICATED SILICONE SHORTING BAR PLR NATURAL SPS/NYLON GF20 STANDARD PLR NATURAL SPS/NYLON GF20 ERGONOMIC GROMMET CAP, PLUGGED BLACK SPS/NYLON GF20 ERGONOMIC GROMMET CAP, OPEN STANDARD GROMMET CAP, PLUGGED BLACK BLACK SPS/NYLON GF20 SPS/NYLON GF20 STANDARD GROMMET CAP, OPEN SPS/NYLON GF20 HOUSING KEYING OPTION D BLACK STONE GRAY HOUSING KEYING OPTION C DARK GRAY SPS/NYLON GF20 HOUSING KEYING OPTION C BLACK SPS/NYLON GF20 HOUSING KEYING OPTION D GREEN SPS/NYLON GF20 HOUSING KEYING OPTION C BROWN SPS/NYLON GF20 HOUSING KEYING OPTION B LIGHT GRAY HOUSING KEYING OPTION A BLACK SPS/NYLON GF20 SPS/NYLON GF20 DESCRIPTION E SPS/NYLON GF20 D MATERIAL COLOR BOM/APPLICABLE COMPONENTS TABLE FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = 0 mm GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 3.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:56 16 0 ANGULAR TOL = CPA RELEASE DATE 2 K RING SEAL CPA DOCUMENT STATUS CPA CPA CPA CPA PLR, SHRT. BAR LIFTER PS 3 CAVITY WITH A NUMBER INDICATES BLOCKED TERMINAL POSITION CAVITY WITHOUT A NUMBER INDICATES OPEN TERMINAL POSITION E ABREVIATION SEE P/N 33471-0477 SEE P/N 33471-0476 NOT RECOMMENDED C B SALEABLE SEE P/N 33471-0479 SEE P/N 33471-0478 NOT VALIDATED NOT VALIDATED NOT RECOMMENDED NOT RECOMMENDED P 4 SALEABLE P P P P GCP 5 SEE P/N 33471-0481 SEE P/N 33471-0480 NOT RECOMMENDED 4 4 4 4 D 6 NOT RECOMMENDED M M M M 1 1 1 1 A C 7 8 NOT RECOMMENDED NOT RECOMMENDED B D 9 4 4 4 4 C C 10 1 1 1 1 D C PS PS PS PS GCO GCO GCO GCO D A 11 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: VKOSHY THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2010/03/31 2010/04/06 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-041 MATERIAL NUMBER PSD 002 GENERAL MARKET 3 W3 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X4 RECEPTACLE SEALED ASSEMBLY MAT SEAL 2 4 OF 6 1 A 20 19 18 17 16 15 KEY C W/ SHRT. BAR, DARK GRAY KEY D W/O MAT SEAL, STONE GRAY KEY C W/O MAT SEAL, DARK GRAY KEY D W/ CPA, STONE GRAY KEY C W/ CPA, DARK GRAY M KEY D, STONE GRAY KEY C, DARK GRAY KEY D W/ CPA, STONE GRAY KEY C W/ CPA, DARK GRAY KEY D, STONE GRAY KEY C, DARK GRAY KEY A, BLACK KEY B, W/ CPA, LIGHT GRAY KEY A, BLACK KEY B, LIGHT GRAY KEY D W/ CPA, STONE GRAY KEY C W/ CPA, DARK GRAY KEY D, STONE GRAY KEY C, DARK GRAY KEY A W/ CPA & ERGO. CAP, BLACK L K J G F 12 ASSEMBLY PART NUMBER P P P P 4 4 P P P P P P P P M M M CPA M CPA M M M M CPA 1 1 4 4 4 4 4 4 4 B GCP GCP GCP GCP GCP GCP GCP GCP B GCP GCP P P P P P P P M M M M M M M P M PS M PS M C D C D C A A C C D GCO GCO D GCO GCO A GCEO A A GCP GCP GCP D D C B A A D C B A D B A C D C C 3 1 PS M PS M PS M CPA CPA CPA M M M M D GCO GCP GCEO GCEP P PS M C B DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 P1 L K 2 SALEABLE SALEABLE J 4 4 2 2 2 2 3 3 3 3 3 4 4 4 4 4 SALEABLE SALEABLE NOT RECOMMENDED SEE P/N 33471-0488 NOT RECOMMENDED NOT RECOMMENDED SEE P/N 33471-0487 SEE P/N 33471-0486 H SALEABLE SALEABLE SEE P/N 33471-0485 SEE P/N 33471-0484 NOT RECOMMENDED NOT RECOMMENDED SALEABLE G SEE P/N 33471-0483 SEE P/N 33471-0482 NOT RECOMMENDED NOT RECOMMENDED SALEABLE COMMENTS STATUS F RING SEAL BURNT ORANGE INHERENTLY LUBRICATED SILICONE CPA BRIGHT RED PBT GF30 MAT SEAL LIGHT BLUE INHERENTLY LUBRICATED SILICONE SHORTING BAR PLR NATURAL SPS/NYLON GF20 STANDARD PLR NATURAL SPS/NYLON GF20 ERGONOMIC GROMMET CAP, PLUGGED BLACK SPS/NYLON GF20 ERGONOMIC GROMMET CAP, OPEN STANDARD GROMMET CAP, PLUGGED BLACK BLACK SPS/NYLON GF20 SPS/NYLON GF20 STANDARD GROMMET CAP, OPEN SPS/NYLON GF20 HOUSING KEYING OPTION D BLACK STONE GRAY HOUSING KEYING OPTION C DARK GRAY SPS/NYLON GF20 HOUSING KEYING OPTION C BLACK SPS/NYLON GF20 B HOUSING KEY B HOUSING KEYING OPTION D GREEN SPS/NYLON GF20 C HOUSING KEY C HOUSING KEYING OPTION C BROWN SPS/NYLON GF20 HOUSING KEYING OPTION B LIGHT GRAY D HOUSING KEY D HOUSING KEYING OPTION A BLACK SPS/NYLON GF20 SPS/NYLON GF20 GCO GROMMET CAP, STANDARD, OPEN DESCRIPTION GCP GROMMET CAP, STANDARD, PLUGGED GCEO GROMMET CAP, ERGONOMIC, OPEN GCEP GROMMET CAP, ERGONOMIC, PLUGGED M MAT SEAL P PLR, STANDARD RELEASE DATE 18 BOM/APPLICABLE COMPONENTS TABLE FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = CPA 0 mm GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 3.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:56 16 0 ANGULAR TOL = RING SEAL 17 D MATERIAL COLOR PLR, SHRT. BAR LIFTER 2020/08/26 E SPS/NYLON GF20 HOUSING KEY A CPA A BOM SHEET 2 A R M CAVITY WITH A NUMBER INDICATES BLOCKED TERMINAL POSITION CAVITY WITHOUT A NUMBER INDICATES OPEN TERMINAL POSITION COMPONENT PS 1 SALEABLE 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 2 3 4 CPA 1 BLOCKED TERMINAL TABLE LEGEND D 2 SALEABLE SALEABLE SALEABLE 1 1 1 1 GCO GCO GCO P P P P 4 1 CPA 3 SALEABLE SALEABLE SALEABLE SALEABLE 3 PS M 4 SALEABLE SALEABLE CPA M M M M M 5 6 SALEABLE SALEABLE SALEABLE SALEABLE SALEABLE SALEABLE CPA CPA GCO GCP GCP GCP GCP C B PS PS PS PS PS GCP GCP GCP GCP GCP 2 2 7 8 1 1 E ABREVIATION 9 M CPA M CPA D A 10 PS M GCO D GCO GCO C D GCP C GCP 33471-0476 33471-0448 33471-0447 33471-0446 33471-0445 33471-0444 33471-0443 33471-0442 33471-0441 11 C 33471-0479 33471-0478 33471-0477 33471-0467 33471-0466 33471-0465 33471-0464 33471-0463 33471-0462 33471-0461 33471-0460 33471-0459 33471-0458 33471-0457 33471-0456 33471-0455 33471-0454 33471-0453 33471-0452 33471-0451 33471-0450 33471-0449 ASSEMBLY DESCRIPTION 13 33471-0480 33471-0475 33471-0474 33471-0473 33471-0472 33471-0471 33471-0470 33471-0469 33471-0468 VOID KEY KEY A, BLACK KEY A W/ SHRT. BAR, BLACK KEY D W/ SHRT. BAR, GREEN VOID KEY KEY D W/ SHRT. BAR, GREEN KEY C W/ SHRT. BAR, BROWN KEY B W/ SHRT. BAR, LT. GRAY KEY A W/ SHRT. BAR, BLACK KEY A W/ SHRT. BAR, BLACK VOID KEY KEY D W/ CPA & SHRT. BAR, GREEN KEY C W/ CPA & SHRT. BAR, BROWN KEY B W/ CPA & SHRT. BAR, LT. GRAY KEY A W/ CPA & SHRT. BAR, BLACK VOID KEY KEY D, GREEN KEY C, BROWN KEY B, LT. GRAY KEY A, BLACK H 14 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: VKOSHY THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2010/03/31 2010/04/06 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-041 MATERIAL NUMBER PSD 002 GENERAL MARKET 3 W3 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X4 RECEPTACLE SEALED ASSEMBLY MAT SEAL 2 5 OF 6 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M BOM SHEET 3 L L K K J J W2 H G KEY B, LT.GRAY KEY A W/ CPA, BLACK KEY A W/ CPA & SHRT. BAR, YELLOW KEY A W/ CPA, YELLOW KEY A W/ CPA, BLACK KEY A , BLACK KEY D W/ SHRT. BAR, STONE GRAY 33471-0494 33471-0493 33471-0492 KEY D W/ SHRT. BAR, STONE GRAY KEY C W/ SHRT. BAR, DARK GRAY KEY D W/ CPA & SHRT. BAR, STONE GRAY KEY C W/ CPA & SHRT. BAR, DARK GRAY KEY D, STONE GRAY KEY C, DARK GRAY 33471-0487 33471-0486 33471-0485 33471-0491 33471-0490 33471-0489 33471-0488 KEY D W/ SHRT. BAR, STONE GRAY A A GCO A GCO A A D D C D D C A B C D C C GCO M M CPA PS M CPA P M CPA P M CPA M P PS M PS M PS M PS M CPA PS M CPA M P P M PS M GCP GCP 2 P P GCP GCP GCP GCP GCP GCO C 33471-0484 33471-0483 33471-0482 33471-0481 ASSEMBLY PART NUMBER ASSEMBLY DESCRIPTION B GCP GCP GCO D D A GCO GCP GCEO GCEP P PS M CPA SALEABLE SALEABLE 3 2 SALEABLE SALEABLE SALEABLE SALEABLE SALEABLE SALEABLE 3 2 4 1 1 2 2 3 3 4 4 1 1 2 2 3 3 4 4 SALEABLE SALEABLE SALEABLE SALEABLE SALEABLE SALEABLE 1 2 3 4 BLOCKED TERMINAL TABLE LEGEND C COMPONENT B DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: J DATE: 2020/01/14 19 INHERENTLY LUBRICATED SILICONE CPA BRIGHT RED PBT GF30 MAT SEAL LIGHT BLUE INHERENTLY LUBRICATED SILICONE SHORTING BAR PLR NATURAL SPS/NYLON GF20 STANDARD PLR NATURAL SPS/NYLON GF20 ERGONOMIC GROMMET CAP, PLUGGED BLACK SPS/NYLON GF20 ERGONOMIC GROMMET CAP, OPEN STANDARD GROMMET CAP, PLUGGED BLACK BLACK SPS/NYLON GF20 SPS/NYLON GF20 STANDARD GROMMET CAP, OPEN BLACK SPS/NYLON GF20 HOUSING KEYING OPTION A HOUSING KEYING OPTION D YELLOW STONE GRAY SPS/NYLON GF20 SPS/NYLON GF20 HOUSING KEYING OPTION C DARK GRAY SPS/NYLON GF20 HOUSING KEYING OPTION C BLACK SPS/NYLON GF20 HOUSING KEYING OPTION D GREEN SPS/NYLON GF20 HOUSING KEYING OPTION C BROWN SPS/NYLON GF20 HOUSING KEYING OPTION B LIGHT GRAY BLACK SPS/NYLON GF20 SPS/NYLON GF20 B HOUSING KEY B C HOUSING KEY C HOUSING KEYING OPTION A D HOUSING KEY D DESCRIPTION GCO GROMMET CAP, STANDARD, OPEN GCP GROMMET CAP, STANDARD, PLUGGED GCEO GROMMET CAP, ERGONOMIC, OPEN GCEP GROMMET CAP, ERGONOMIC, PLUGGED M MAT SEAL P PLR, STANDARD P1 FUNCTIONAL THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C SYMBOLS DIMENSION UNITS SCALE CURRENT REV DESC: = = 18 17 0 mm GENERAL TOLERANCES (UNLESS SPECIFIED) ± 4 PLACES ± DIVISIONAL 3 PLACES SYMBOLS ± 0 3.0 ° 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 07:23:56 16 0 ANGULAR TOL = CPA 2020/08/26 D BOM/APPLICABLE COMPONENTS TABLE RING SEAL RELEASE DATE E MATERIAL COLOR PLR, SHRT. BAR LIFTER CPA A BURNT ORANGE HOUSING KEY A R F RING SEAL A PS COMMENTS CAVITY WITH A NUMBER INDICATES BLOCKED TERMINAL POSITION CAVITY WITHOUT A NUMBER INDICATES OPEN TERMINAL POSITION E D G STATUS F ABREVIATION H 15 14 13 12 11 10 9 8 7 EC NO: 643941 DRWN: XLDONG03 CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: VKOSHY THIRD ANGLE PROJECTION 2020/08/21 2020/08/26 2020/08/26 DRAWING 5 2010/03/31 2010/04/06 SERIES 33471 DOC TYPE DOC PART REVISION SD-33471-041 MATERIAL NUMBER PSD 002 GENERAL MARKET 3 W3 SHEET NUMBER CUSTOMER SEE BOM 4 B PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER D-SIZE 6 MX150 1X4 RECEPTACLE SEALED ASSEMBLY MAT SEAL 2 6 OF 6 1 A 19 L 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 L TABLE OF CONTENTS K SHEET NO. SHEET DESCRIPTION 1 NOTES 2 KEY CONFIGURATIONS 3 BLADE SEALED ASSEMBLY 4 SYSTEM PACKAGING 5 BOM NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: a. APPLICATION SPECIFICATION SEE: AS-33472-100 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, CONNECTOR ASSEMBLY, PACKAGING INFORMATION, CONNECTOR MATING, SERVICE INSTRUCTIONS, ELECTRICAL CONTINUITY CHECKING, CRIMPING, AND TROUBLESHOOTING. -DESIGNED TO MATE WITH RECEPTACLE SEALED ASSEMBLY SPECIFIED IN MOLEX DRAWING SD-33471-041. -FOR 1.5mm BLADE TERMINALS TO BE USED WITH THIS ASSEMBLY SEE MOLEX DRAWING SD-33000-001. - SYSTEM TO BE USED WITH WIRE WITHIN DIAMETER RANGE OF 1.2mm TO 2.69mm. -ASSEMBLY SHIPPED WITH PLR IN PRE-LOCK POSITION -IN THE EVENT THAT THE PLR IS FOUND IN THE SEATED (FINAL LOCK) POSITION, REFER TO MOLEX SPECIFICATION PS-34646-001, AVAILABLE AT www.molex.com -ASSEMBLY CONFORMS TO SAE/USCAR-2 REV.4 WITH THE FOLLOWING EXCEPTIONS: TERMINAL INSERTION FORCE FOR WIRE DIAMETER ABOVE 2.5mm NOT EXCEEDING 2.69mm SHALL NOT EXCEED 45 NEWTONS. b. PRODUCT SPECIFICATION SEE: PS-33471-000 CONTAINS: PRODUCT INTRODUCTION, PRODUCT SUMMARY, RATINGS (CURRENT, TEMPERATURE, SEALING, AND FLAMMABILITY), AND PRODUCT VALIDATION. c. PACKAGING SPECIFICATION PER MOLEX DRAWING: PK-31300-635 d. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR PRODUCTS AND PACKAGING SPECIFICATION: ES-40000-5016 e. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) f. FOR INFORMATION ON 1X4 BLADE SEALED ASSEMBLY WITH SHORTING BAR SEE SD-31280-200. J GROMMET CAP H K J H 2. DESIGN - MATERIALS: a. CONNECTOR HOUSING, GROMMET CAP, PLR: SPS/NYLON BLEND 20% GLASS FILLED b. MAT SEAL: INHERENTLY LUBRICATED SILICONE MAT SEAL 3. DESIGN - GEOMETRY: a. THIS IS A 100% CAD GENERATED PART. THE CAD MATHEMATICAL DATA IS THE MASTER FOR THIS PART. FOR DIMENSIONAL OR ANY INFORMATION NOT SHOWN ON THIS DRAWING, ANALYZE THE CAD MODEL. b. GEOMETRIC DIMENSIONS AND TOLERANCES PER ASME Y14.5M - 1994 c. EDGES AND UNDIMENSIONED DETAILS PER ISO13715 d. CORNERS SHOWN AS SHARP TO BE R 0.2 MAX. e. LETTERING SHALL BE 0.15 MAX RAISED IN 0.25 MAX RECESS PAD. THIS INCLUDES RECYCLING CODE, CAVITY ID, VENDOR IDENTIFICATION, AND CUSTOMER MATERIAL NUMBER. f. VISUAL DEFECTS SHALL MEET COSMETIC STANDARD PS-45499-002 (Class B) g. LASER MARKING: TBD G CONNECTOR HOUSING FOR OPTIONS SEE BOM F G F PRIMARY LOCK REINFORCEMENT (PLR) E E D D C C SYMBOLS = 0 = 0 B = 0 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/12/04 16 17:46:22 C 15 14 13 12 11 10 9 8 mm 3:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± = 0 DOCUMENT STATUS SCALE ANGULAR TOL = 0 A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 7 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 607930 DRWN: HKLIANG CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL 2018/11/09 2018/12/04 2018/12/04 2005/08/26 2005/08/29 DRAWING SERIES D-SIZE 33481 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-041 MATERIAL NUMBER PSD 001 SHEET NUMBER CUSTOMER GENERAL MARKET 3 W2 2 1 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 KEY CONFIGURATIONS L 60° L 60° K K J J KEY A 30° 60° H H G G KEY B F F 30° 60° E E D D KEY C C C 30° 30° SYMBOLS = 0 = 0 B = 0 KEY D A FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/12/04 16 17:46:22 15 14 13 12 11 10 9 8 mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± = 0 C SCALE ANGULAR TOL = 0 DOCUMENT STATUS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 7 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 607930 DRWN: HKLIANG CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL 2018/11/09 2018/12/04 2018/12/04 2005/08/26 2005/08/29 DRAWING SERIES D-SIZE 33481 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-041 MATERIAL NUMBER PSD 001 SHEET NUMBER CUSTOMER GENERAL MARKET 3 W2 2 2 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 BLADE SEALED ASSEMBLY L LASER MARKING THIS SURFACE Y SEE NOTE 3g. L ⌀25.27 MIN PASS-THRU WITH NO CLEARANCE Z K K 17.13+0.10 -0.25 X 2 X J J Y 3X3.50 TERMINAL POSITION 4 4 Z 53.85±0.60 1 TERMINAL POSITION 1 22.44±0.20 REAR VIEW (WIRE HARNESS SIDE) H H G G 2.00 7 6 11.00 F F 6.60 15.00 8 5 E E PARTIAL X-X SCALE 4:1 D D C C SYMBOLS = 0 = 0 B = 0 PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN FINAL-LOCK POSITION PRIMARY LOCK REINFORCEMENT (PLR) SHOWN IN PRE-STAGED POSITION SECTION Z-Z A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/12/04 16 17:46:22 15 14 13 12 11 10 9 8 mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± = 0 C SCALE ANGULAR TOL = 0 SECTION Y-Y THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 7 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 607930 DRWN: HKLIANG CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL 2018/11/09 2018/12/04 2018/12/04 2005/08/26 2005/08/29 DRAWING SERIES D-SIZE 33481 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-041 MATERIAL NUMBER PSD 001 SHEET NUMBER CUSTOMER GENERAL MARKET 3 W2 2 3 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 SYSTEM PACKAGING L L K K J J ⌀A MIN. PASS-THROUGH WITH NO CLEARANCE H H (72.70) OVERALL MATED SYSTEM G G F F E E D D CHARTED DIMENSIONS A CONFIGURATION C MX150 1X4 RECPT SEALED ASSY - STANDARD 29.14 MX150 1X4 RECPT SEALED ASSY - ERGO 29.33 MX150 1X4 RECPT SEALED ASSY - SHORTING (SHRT) BAR SYMBOLS = 0 = 0 B = 0 A DOCUMENT STATUS FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/12/04 16 17:46:22 C 15 14 13 12 11 10 9 8 SCALE mm 4:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± = 0 = 0 7 29.14 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL = 0 C 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 607930 DRWN: HKLIANG CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL 2018/11/09 2018/12/04 2018/12/04 2005/08/26 2005/08/29 DRAWING SERIES D-SIZE 33481 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-041 MATERIAL NUMBER PSD 001 SHEET NUMBER CUSTOMER GENERAL MARKET 3 W2 2 4 OF 5 1 A 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 BOM L L ASSEMBLY PART NUMBER 33481-0401 33481-0402 33481-0403 33481-0404 33481-0405 33481-0406 33481-0407 33481-0408 33481-0409 33481-0410 33481-0411 33481-0412 33481-0413 33481-0414 33481-0415 33481-0416 33481-0417 33481-0418 33481-0419 33481-0420 33481-0421 33481-0422 33481-0423 K J H G 33481-0424 33481-0425 33481-0426 33481-0427 33481-0428 33481-0429 33481-0430 F W2 COLOR KEYING OPTION BLACK LT. GRAY BROWN GREEN BLACK BLACK LT. GRAY BROWN GREEN CUSTOM BLACK LT. GRAY BROWN GREEN CUSTOM BLACK LT. GRAY BROWN GREEN CUSTOM BLACK BLACK LT. GRAY DK. GRAY ST. GRAY DK. GRAY ST. GRAY YELLOW A B C D C A B C D TBD A B C D TBD A B C D TBD A A B C D LT. GRAY BLACK B A C D A CAVITY TYPE & STATUS ( X = PLUGGED) 1 2 3 COMMENTS STATUS 4 ASSEMBLY PART NUMBER 33481-4401 33481-4402 33481-4403 33481-4404 33481-4405 33481-4406 33481-4407 33481-4408 33481-4409 33481-4410 33481-4411 33481-4412 33481-4413 33481-4414 33481-4415 33481-4416 33481-4417 33481-4418 33481-4419 33481-4420 33481-4421 33481-4422 33481-4423 NOT RECOMMENDED, SEE P/N 33481-0424 NOT RECOMMENDED, SEE P/N 33481-0425 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X NOT RECOMMENDED, SEE P/N 33481-0426 NOT RECOMMENDED, SEE P/N 33481-0427 X 33481-4424 X X X X X X X X X X X X W2 33481-4425 33481-4426 33481-4427 33481-4428 33481-4429 33481-4430 CAVITY TYPE & STATUS ( X = PLUGGED) KEYING OPTION COLOR BLACK LT. GRAY BROWN GREEN BLACK BLACK LT. GRAY BROWN GREEN CUSTOM BLACK LT. GRAY BROWN GREEN CUSTOM BLACK LT. GRAY BROWN GREEN CUSTOM BLACK BLACK LT. GRAY DK. GRAY ST. GRAY DK. GRAY ST. GRAY YELLOW A B C D C A B C D TBD A B C D TBD A B C D TBD A A B C D LT. GRAY BLACK B A 1 2 3 COMMENTS STATUS 4 K NOT RECOMMENDED, SEE P/N 33481-4424 NOT RECOMMENDED, SEE P/N 33481-4425 X X X X X X X X X X C D A X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X J H NOT RECOMMENDED, SEE P/N 33481-4426 NOT RECOMMENDED, SEE P/N 33481-4427 G X X X F E E D D C C SYMBOLS = 0 = 0 B = 0 FORMAT: master-tb-prod-D REVISION: H DATE: 2018/01/18 19 P1 18 RELEASE DATE 17 2018/12/04 16 17:46:22 C 15 14 13 12 11 10 9 8 mm 1:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 0.1 1 PLACE ± 0.3 0 PLACES ± = 0 DOCUMENT STATUS SCALE ANGULAR TOL = 0 A THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS = 0 7 3.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 CURRENT REV DESC: B EC NO: 607930 DRWN: HKLIANG CHK'D: JDENG02 APPR: JDENG02 INITIAL REVISION: DRWN: DGRIFFITHS APPR: smarceau THIRD ANGLE PROJECTION 5 MX150 1X4 BLADE SEALED ASSEMBLY MAT SEAL 2018/11/09 2018/12/04 2018/12/04 2005/08/26 2005/08/29 DRAWING SERIES D-SIZE 33481 4 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-33481-041 MATERIAL NUMBER PSD 001 SHEET NUMBER CUSTOMER GENERAL MARKET 3 W2 2 5 OF 5 1 A