347520204

19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 L L ASSEMBLY NUMBER A B C D A B C D 34752-0200 34752-0201 34752-0202 34752-0203 34752-0204 34752-0205 34752-0206 34752-0207 K COLOR KEYING OPTION BLACK LT. GRAY DK. GRAY STONE GRAY BLACK LT. GRAY DK. GRAY STONE GRAY CPA STATUS X X X X SALEABLE CONCEPT ONLY CONCEPT ONLY CONCEPT ONLY SALEABLE CONCEPT ONLY CONCEPT ONLY CONCEPT ONLY MODEL NUMBER CPA (OPTIONAL) EM-34752-020 EM-34752-021 EM-34752-022 EM-34752-023 EM-34752-020 EM-34752-021 EM-34752-022 EM-34752-023 HOUSING K SCALE 1:1 PERIMETER SEAL TPA J J A H 9.05 LASER MARKING APPLIED TO H 71 THIS SURFACE TO INCLUDE: MOLEX P/N AND DATE CODE SEE NOTE 1d NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: G G a. PRODUCT SPECIFICATION SEE MOLEX DOCUMENT: PS-34752-001 b. PACKAGING SPECIFICATION PER MOLEX DRAWING: PK-31300-635 KEYING OPTION A c. APPLICATION SPECIFICATION SEE MOLEX DOCUMENT: AS-34752-001 SECTION A-A 23.5 APP. SPEC. CONTAINS THE FOLLOWING INFORMATION ˒ APPROPRIATE TERMIALS TO BE USED 3 ˒ PLR / CPA USAGE ˒ MATING INTERFACES F F d. DATE CODE: FIRST TWO DIGITS IS CALENDAR YEAR, ⌀30.00 MINIMUM PASS THRU THIRD THRU FIFTH DIGIT IS DAY NUMBER OF THE CALENDAR YEAR (FEB. 3RD, 2003 = 0341) A e. PARTS MUST BE IN COMPLIANCE TO MOLEX CHEMICAL SUBSTANCES FOR 2.20.5 PRODUCTS AND PACKAGING SPECIFICATION: ES-40000-5016 1 f. DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS KEYING OPTION B E (COMPANY ID#13255) 2 E 23.2 2. DESIGN - MATERIALS: 4 a. HOUSING: SPS/NYLON BLEND, 20% GLASS FILLED, 20 % MAX REGRIND 2.00.5 COLOR: SEE TABLE 8 b. TPA: SPS/NYLON BLEND, 20% GLASS FILLED, 20 % MAX REGRIND 29.3 D A COLOR: NATURAL TERMINAL POSITION 2 TERMINAL POSITION 1 D c. CPA: PBT 30% GLASS FILLED, 20% MAX REGRIND COLOR: RED d. PERIMETER SEAL: INHERENTLY LUBRICATED SILICONE, 50 DUROMETER COLOR: DK BLUE 3. PACKAGING: IN THE EVENT THAT INERT IS FOUND IN THE SEATED (FINAL MANUFACTURING LOCATION CODE AVAILABLE AT WWW.MOLEX.COM XXX XX KEYING OPTION D 0 ANGULAR TOL ± 3.0 ° = 0 4 PLACES = 0 = 0 = 0 A RELEASE STATUS 19 RELEASE DATE 18 C 17 16 15 14 13 12 11 10 9 8 7 DRWN BY = = 0 = 0 E1 3 PLACES ± 2 PLACES ± 0.1 ± 0 PLACES ± 9/16/08 DATE MX150 CABLE SEAL SINGLE ROW, RECEPTACLE 1X2, ASSEMBLY 9/16/08 DATE PRODUCT CUSTOMER DRAWING 0.2 9/16/08 V.KOSHY DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 B S.VERZYL APPR BY 1 PLACE DATE M.VANSLAMBRO ± CHK'D BY REV B 2017/07/11 2017/05/31 MOLD CAVITY ID. FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 C QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES MM 2:1 = 0 (UNLESS SPECIFIED) EC NO: 118883 DRWN: PKABBUR CHK'D: APPR: KDEKOSKI C LOCK) POSITION, REFER TO MOLEX SPECIFICATION PS-34646-001, RECYCLE CODE XXX/XX KEYING OPTION C THIRD ANGLE PROJECTION D 5 MATERIAL NUMBER SERIES 34752 SEE TABLE DOCUMENT NUMBER SD-34752-020 4 CUSTOMER 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 000 1 OF 2 1 A 19 18 17 16 15 14 13 12 11 10 9 5 6 4 PACKAGING FRAME CL OF B ELIMINATION OF BACK ANGLE L 7 8 3 2 1 CL OF C L REQUIRES APPROVAL BY RESPONSIBLE ENGINEER 8.7 8.5 CL OF C 11.65 MIN. 1.1 ISOMETRIC VIEW 1.0 K OPTION A A CL OF B 10° 2X R K 1.65 1.45 0.35 0.05 14.75 14.75 CL OF B 20.5 J SCALE: 1:1 12.0 16.0 24° ⌖ 0.10 Ⓜ A B Ⓜ J 11.90 MIN. 45° 150-S-002-1-A02 (OPTION A SHOWN) IF HEADER IS RECESSED INTO A POCKET, THESE DIMENSIONS REPRESENT THE CLEARANCE REQUIRED FOR THE MATING CONNECTOR SHROUD 2.55 2.35 1.7 1.5 H 7.4 2X 6.55 6.25 H ⌖ 0.25 Ⓜ A B DETAIL E 10.75 10.45 SCALE 8:1 A 14.3 14.1 **8.025 **8.025 0.100 0.100 D G G D B 4.5 ** 2X 10.75 TO GUIDE SURFACES 0.10 2.25 A 0.35 0.05 F A 2X R CL OF BLADE TO CL DATUM OF DETAIL "E" **(3.10) TO LOCK 2X R 0.45 0.15 (OPTIONAL FOR PANAL MOUNT) 2X 17.5MIN. 10.65 10.45 1.0 3.4 3.2 R2.0 RAMP SURFACE 2X4.5° C C F 1.05 C 2X 6.05 TO SLOTS SURFACE 3X 7.65 10.1 9.9 ⌖ 0.20 Ⓜ A C 9.9AT G 9.7 CL OF C E TERMINAL 2 TERMINAL 1 CL OF C B Left1 R 2X 6.85 E 2X R5.0 R 3.0 MIN CL OF B 2X (0.8) ⌖ 0.20 Ⓜ A CAT BASE ** 2X 7.00 MEASURED AT ⌖ 0.30 Ⓜ A CAT TIP 0.15 D 2X (1.50) SECTION A-A NOTES: CL OF BLADE TERMINALS ⌖ 0.30 Ⓜ A B 15° 2. DIMENSIONING AND TOLERANCING PER ASME Y14,5M-1994. 2.5 (2.00) UNSPECIFIED RADII: 0.25 EXCEPT AS NOTED ⌖ 0.10 Ⓜ A B Ⓜ B 16.65 16.35 D SECTION B-B 20.5 1. ALL DIMENSIONS SHOWN IN MILLIMETERS 3. RADII ON ALL CORNERS SHOWN SHARP OR ALL 6.0 150-S-002-D02 150-S-002-C02 150-S-002-B02 150-S-002-A02 EWCAP P/N NO DRAFT ALL AROUND UNSPECIFIED TOLERANCES ARE AS FOLLOWS .X = 0.25 C .XX = .13 ANGLES ±2° 15.0 15.5 AT DATUM G 4. DESIGN IS BASED ON USCAR DWG. 150-S-002-1-Z02 REV K CL OF C G1 A 0.55 0.25 0.30 C MINIMUM TO CONNECTOR FLOOR D C B A OPTION GREEN BROWN GREY BLACK MATING CONNECTOR COLOR C EXCEPT DIMENSIONS MARKED WITH ** FREE OF SURFACE DEFECTS 5. STANDARD COLORS FOR POLARIZATION - DEVIATION FOR SEALING ALL AROUND REQUIRES APPROVAL OF AUTHORIZED PERSONS. G1 6. SECTION LINES ARE COMMON TO ALL OPTIONS. 7. 1° DRAFT MAX ON OUTSIDE SURFACES PERMISSIBLE ⌖ 0.20 Ⓜ A B IS NOT CONTROLLED BY EWCAP. 9. FOR BLADE GEOMETRY AND PLATING REQUIREMENTS NO PLASTIC MAY EXTEND REFER TO EWCAP DWG. NO. EWCAP-001 REV F, DETAIL 150-T001 ABOVE THIS SURFACE SECTION C-C 10. DIRECTION OF DRAFT REQUIRED. RELEASE STATUS 19 RELEASE DATE 18 C 17 ANGULAR TOL ± 3.0 ° = 0 4 PLACES = 0 16 15 14 13 12 11 10 9 8 7 = 0 = 0 = 0 = 0 E1 3 PLACES ± 2 PLACES ± 0.1 ± 0 PLACES ± 9/16/08 DATE MX150 CABLE SEAL SINGLE ROW, RECEPTACLE 1X2, ASSEMBLY 9/16/08 DATE PRODUCT CUSTOMER DRAWING 0.2 9/16/08 V.KOSHY DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 B S.VERZYL APPR BY 1 PLACE DATE M.VANSLAMBRO ± CHK'D BY REV CONSTRUCTION BELOW THIS SURFACE 8. DIMENSIONS IN ( )ARE FOR REFERENCE. FORMAT: master-tb-prod-D REVISION: G DATE: 2017/02/06 0 AT DATUM G WITHIN ALLOWABLE TOLERANCE. A CL OF B 16.4 16.2 DRWN BY = EC NO: 118883 DRWN: PKABBUR CHK'D: APPR: KDEKOSKI B 2017/05/31 DIMENSION MUST BE FOR ADDITIONAL INFORMATION. 2017/07/11 QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE GENERAL SYMBOLS TOLERANCES MM 3:1 = 0 (UNLESS SPECIFIED) REFER TO "SAE/USCAR-12 CONNECTOR DESIGN GUIDELINES THIRD ANGLE PROJECTION D 5 MATERIAL NUMBER SERIES 34752 150-S-002-1-Z02 DOCUMENT NUMBER SD-34752-020 4 CUSTOMER 3 GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER PSD 2 000 2 OF 2 1 A