42817-0011

12 11 10 9 7 8 5 6 4 2.50 .098 3 2 D 1 A H H 1.30 .051 MATING AREA (SEE NOTE 12) R. F 3.10 .122 R. C B E G G 2.00 ±0.10 .079 ±.004 0.50 MAX CUT-OFF .020 IN CRIMP TOOLING SECTION C-C (BACKGROUND OMITTED) SECTION B-B 10 F F DIM G 3.80 ±0.15 .150 ±.006 0.90 .035 C 9 B E E 4.8 .189 6.20 .244 B D MATING AREA C D 12 & 10 AWG TERMINAL 12 AWG WIRE CONDUCTOR STRAIN RELIEF (SEE NOTE 8) C C CONDUCTOR CRIMP 8 AWG TERMINAL 12 AWG DOUBLE CRIMP (SEE NOTE 13) "SUPERFLEX WIRE" SHRINK TUBING B ISOMETRIC VIEW (SCALE 4:1) CRIMP AREA 8 AWG TERMINAL (SEE NOTE 8) B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN 8:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) MM 8 AWG TERMINAL (SEE NOTE 11) A 4 PLACES ± ± 3 PLACES ± ± 0.25 ± 0.016 ± 0.4 ± 0 PLACES ± ANGULAR TOL DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 P1 RELEASE DATE 11 2022/04/12 10 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:32:37 9 0.01 2 PLACES ± 1 PLACE THIS DOCUMENT HAS BEEN RE-ISSUED BASED ON SD-42817-*, REV J. INCH 8 7 6 5 EC NO: 703014 DRWN: SHRUTJ CHK'D: SHRUTJ APPR: ISHWARG INITIAL REVISION: DRWN: RJF APPR: RAS THIRD ANGLE PROJECTION 4 2022/04/12 2022/04/12 2022/04/12 MALE CRIMP TERMINAL, 12, 10 & 8AWG MINI-FIT SR. PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1992/07/01 1992/07/01 DRAWING SERIES C-SIZE 42817 3 428170000-SD MATERIAL NUMBER PSD 000 CUSTOMER SEE CHART 2 A2 SHEET NUMBER GENERAL MARKET 1 OF 2 1 A 12 11 ITEM NUMBER WIRE RANGE H 428170011 12 & 10 AWG (5 & 6mm^2) 428170031 8 AWG 428170111 12 & 10 AWG (5 & 6mm^2) 428170131 8 AWG 428170012 12 & 10 AWG (5 & 6mm^2) G 8 AWG 428170032 428170112 428170132 F 428171014 428171034 428171114 428171134 10 9 DIM. A DIM. B 5.40±.60 [.213±.024] 6.10±.40 [.240±.016] 5.83±.60 [.229±.024] 5.40±.60 [.213±.024] 5.83±.60 [.229±.024] 5.40±.60 [.213±.024] 5.83±.60 [.229±.024] 7.42±.40 [.292±.016] 6.10±.40 [.240±.016] 7.42±.40 [.292±.016] 6.10±.40 [.240±.016] 7.42±.40 [.292±.016] 12 & 10 AWG 5.40 ± .60 (5 & 6mm^2) [.213 ± .024] 5.83 ± .60 8 AWG [.229 ± .024] 12 & 10 AWG 5.40 ± .60 (5 & 6mm^2) [.213 ± .024] 5.83 ± .60 8 AWG [.229 ± .024] 12 & 10 AWG 5.40 ± .60 (5 & 6mm^2) [.213 ± .024] 5.83 ± .60 8 AWG [.229 ± .024] 6.10 ± .40 [.240 ± .016] 7.42 ± .40 [.292 ± .016] 6.10 ± .40 [.240 ± .016] 7.42 ± .40 [.292 ± .016] 6.10 ± .40 [.240 ± .016] 7.42 ± .40 [.292 ± .016] 7 8 MAX. INSULATION DIAMETER DIM. D DIM. E DIM. F DIM. G R 1.70 [.067] 5.90±.60 [.232±.024] 6.60±.40 [.260±.016] R. 2.20 27.60 [.087] [1.087] 5.30 DIA. [.209] R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] 6.00±.60 [.236±.024] 5.90±.60 [.232±.024] 6.00±.60 [.236±.024] 5.90±.60 [.232±.024] 6.00±.60 [.236±.024] 5.50±.40 [.216±.016] 6.60±.40 [.260±.016] 5.50±.40 [.216±.016] 6.60±.40 [.260±.016] 5.50±.40 [.216±.016] 5.90 ± .60 [.232 ± .024] 6.00 ± .60 [.236 ± .024] 5.90 ± .60 [.232 ± .024] 6.00 ± .60 [.236 ± .024] 5.90 ± .60 [.232 ± .024] 6.00 ± .60 [.236 ± .024] 6.60 ± .40 [.260 ± .016] 5.50 ± .40 [.216 ± .016] 6.60 ± .40 [.260 ± .016] 5.50 ± .40 [.216 ± .016] 6.60 ± .40 [.260 ± .016] 5.50 ± .40 [.216 ± .016] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] R. 2.20 [.087] 6.60 DIA. [.260] 5.30 DIA. [.209] 6.60 DIA. [.260] 5.30 DIA. [.209] 6.60 DIA. [.260] 5.30 DIA. [.209] 6.60 DIA. [.260] 5.30 DIA. [.209] 6.60 DIA. [.260] 5.30 DIA. [.209] 6.60 DIA. [.260] DIM. C R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] R 1.70 [.067] 5 6 27.60 [1.087] 29.60 [1.165] 29.60 [1.165] 27.60 [1.087] 27.60 [1.087] 29.60 [1.165] 29.60 [1.165] 27.60 [1.087] 27.60 [1.087] 29.60 [1.165] 29.60 [1.165] 4 PLATING 3 2 1 STATUS H PLANNED FOR OBSOLESCENCE OVERALL TIN G SELECT GOLD ACTIVE F ACTIVE SELECT SILVER E D C B A E NOTES: 1) MATERIAL: COPPER ALLOY 151, .020/(.50) THICK. 2) PLATING: 1= .000100/(.00254) MIN.TIN OVER .000050/(.00127) MIN.NICKEL. 2= .000030/(.00076) MIN. SELECT GOLD IN CONTACT AREA. .000100/(.00254) MIN. SELECT TIN ON SOLDER TAILS OVER .000050/(.00127) MIN. NICKEL. 4= .000100/(.00254) MINIMUM SELECT SILVER IN CONTACT AREA. .000100/(.00254) MIN. SELECT TIN ON SOLDER TAILS OVER .000050/(.00127) MIN. NICKEL. 3) PRODUCT SPEC: PS-42815-001. 4) PACKAGING INFORMATION: PK-42815-001. 5) PART IS DESIGNED IN METRIC. 6) TERMINALS FOR USE WITH STRANDED WIRE ONLY. 7) ITEM NUMBERS PRECEEDED BY AN "X" IN THE CHART ARE NOT AVAILABLE. 8) THE 8 AWG TERMINAL HAS NO INSULATION CRIMP.THE SECONDARY CRIMP SECTION ACTS AS A STRAIN RELIEF ON THE BARE CONDUCTOR ONLY. SEE MOLEX CRIMP SPECIFICATION FOR DETAILS. 9 AFTER CRIMPING, THIS DIMENSION IS .140/(3.55) MINIMUM. 10 AFTER CRIMPING, THIS DIMENSION IS .089/(2.25) MINIMUM. 11) WHEN USING THE 8 AWG TERMINAL WITH "HI-FLEX" WIRE, MOLEX STRONGLY RECOMMENDS THAT THE APPROPRIATELY RATED HEAT SHRINK INSULATION BE APPLIED OVER THE WIRE INSULATION AND CRIMP AREA, AS SHOWN. TO MINIMIZE WIRE INSULATION CREEPAGE OUTSIDE OF HOUSING. D 12) WHEN USING OVERALL TIN PLATED TERMINALS. FOR APPLICATIONS INVOLVING VIBRATION AND/OR THERMAL CYCLING. MOLEX STRONGLY RECOMMENDS THE USE OF NYE LUBRICANT.NYOGEL 760G. ON THE MATING AREA OF THE TERMINAL. LUBRICANT SHOULD BE APPLIED AFTER THE TERMINALS ARE INSERTED INTO THE HOUSING. REFER AS-42815-001 FOR ADDITIONAL INFORMATION. 13) THE 8 AWG TERMINAL WILL ALSO ACCOMODATE 2 12 AWG WIRES SEE CRIMP SPEC FOR DETAILS. 14) THIS DRAWING REPLACES SD-42817-*, REV J AND 428170000 REV. A. B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE MM/IN 8:1 MM P1 RELEASE DATE 11 2022/04/12 10 INCH 4 PLACES ± ± 3 PLACES ± ± 0.01 2 PLACES ± 0.25 ± 0.016 ± 0.4 ± 1 PLACE ANGULAR TOL DOCUMENT STATUS 12 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) 0 PLACES ± FORMAT: Eng-lega-master-tb-prod-C REVISION: D DATE: 2018/01/18 ± ± 0.5 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 10:32:37 9 8 C 7 6 5 EC NO: 703014 DRWN: SHRUTJ CHK'D: SHRUTJ APPR: ISHWARG INITIAL REVISION: DRWN: RJF APPR: RAS THIRD ANGLE PROJECTION 4 2022/04/12 2022/04/12 2022/04/12 MALE CRIMP TERMINAL, 12, 10 & 8AWG MINI-FIT SR. PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 1992/07/01 1992/07/01 DRAWING SERIES C-SIZE 42817 3 428170000-SD MATERIAL NUMBER PSD 000 CUSTOMER SEE CHART 2 A2 SHEET NUMBER GENERAL MARKET 2 OF 2 1 A