PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
1.0 SCOPE
This product specification covers 3.18/(.125”) X 0.51/(.020”) flat blade type connectors in wire-to-wire,
wire-to-board, and wire-to-“device” type connections. Two types of connectors are addressed:
(1) standard – 7.50 mm (.295”) centerline spacing series, and
(2) custom connector housings.
2.0 PRODUCT DESCRIPTION
The products described herein are useful in home appliances such as clothes washers, dryers, dish
washers, and refrigerators. The terminals have integral secondary locks that, when activated
(optional), substantially improve their locking reliability, and virtually eliminate terminal “back-outs.”
These connectors have long “through air” and “over surface” spacings to resist moisture and other
pollutants that are present in appliances. The header assemblies are compatible with surface mount
soldering processes.
The terminals crimp to wire insulation with a maximum 4.57 mm (.180”) outside diameter, and
accommodate standard power cord insulation as well.
The female terminal is fabricated from tin plated C26000. The male tab crimp terminal is fabricated
from bare, un-plated C26000. The header terminal is fabricated from tin plated C26000. The male
terminals are 3.18/(.125”) X 0.51/(.020”) tabs that are designed within the limits of the ANSI/NEMA
Standards Publication / No. DC 2-1982. The terminations to #18, #16, and #14 AWG wires are
accommodated as single crimps. Additionally, #18 AWG wire, UL 1015 only, is accommodated as a
double crimp. This is a power connector, but it can be used as a dry circuit connector, too.
(1) Standard – 7.50 mm (.295”) Centerline Spacing Series:
The plug and receptacle housings are molded from 66 nylon in its natural color, translucent white,
unless otherwise indicated. The header housings are molded from glass filled 46 nylon in a black
color. Also, the flammability classification for each housing material is listed below:
PRODUCT NAME:
PLUG HOUSING, 2 CIRCUIT (UL94V-2), NATURAL
PLUG HOUSING, 2 CIRCUIT (UL94V-2), RED
PLUG HOUSING, 3 CIRCUIT (UL94V-2), NATURAL
PLUG HOUSING, 3 CIRCUIT (UL94V-2), RED
PLUG HOUSING, 3 CIRCUIT (UL94V-2), BLUE
PLUG HOUSING, 4 CIRCUIT (UL94V-2)
PLUG HOUSING, 5 CIRCUIT (UL94V-2)
PLUG HOUSING, 6 CIRCUIT (UL94V-2)
MATERIAL NUMBER:
43180-1002
43180-3002
43180-1003
43180-3003
43180-4003
X-43180-1004
X-43180-1005
X-43180-1006
PANEL MOUNT PLUG HOUSING, 2 CIRCUIT (UL94V-2)
PANEL MOUNT PLUG HOUSING, 3 CIRCUIT (UL94V-2)
PANEL MOUNT PLUG HOUSING, 4 CIRCUIT (UL94V-2)
PANEL MOUNT PLUG HOUSING, 5 CIRCUIT (UL94V-2)
PANEL MOUNT PLUG HOUSING, 6 CIRCUIT (UL94V-2)
REVISION:
4
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
X-43384-1002
43384-1003
X-43384-1004
X-43384-1005
X-43384-1006
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
1 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
2.0 PRODUCT DESCRIPTION (CONTINUED):
PRODUCT NAME:
RECEPTACLE HOUSING, 2 CIRCUIT (UL94V-2), NATURAL
RECEPTACLE HOUSING, 2 CIRCUIT (UL94V-2), BLACK
RECEPTACLE HOUSING, 2 CIRCUIT (UL94V-2), RED
RECEPTACLE HOUSING, 3 CIRCUIT (UL94V-2), NATURAL
RECEPTACLE HOUSING, 3 CIRCUIT (UL94V-2), BLACK
RECEPTACLE HOUSING, 3 CIRCUIT (UL94V-2), RED
RECEPTACLE HOUSING, 3 CIRCUIT (UL94V-2), BLUE
RECEPTACLE HOUSING, 4 CIRCUIT (UL94V-2)
RECEPTACLE HOUSING, 5 CIRCUIT (UL94V-2)
RECEPTACLE HOUSING, 6 CIRCUIT (UL94V-2)
MATERIAL NUMBER:
43335-1002
43335-2002
43335-3002
43335-1003
43335-2003
43335-3003
43335-4003
X-43335-1004
X-43335-1005
X-43335-1006
HEADER ASSEMBLY, 2 CIRCUIT, VERTICAL (UL94V-0)
HEADER ASSEMBLY, 3 CIRCUIT, VERTICAL (UL94V-0)
HEADER ASSEMBLY, 4 CIRCUIT, VERTICAL (UL94V-0)
HEADER ASSEMBLY, 5 CIRCUIT, VERTICAL (UL94V-0)
HEADER ASSEMBLY, 6 CIRCUIT, VERTICAL (UL94V-0)
SEE SDA-43160-****
SEE SDA-43160-****
SEE SDA-43160-****
SEE SDA-43160-****
SEE SDA-43160-****
HEADER ASSEMBLY, 2 CIRCUIT, RIGHT ANGLE (UL94V-0)
HEADER ASSEMBLY, 3 CIRCUIT, RIGHT ANGLE (UL94V-0)
HEADER ASSEMBLY, 4 CIRCUIT, RIGHT ANGLE (UL94V-0)
HEADER ASSEMBLY, 5 CIRCUIT, RIGHT ANGLE (UL94V-0)
HEADER ASSEMBLY, 6 CIRCUIT, RIGHT ANGLE (UL94V-0)
SEE SDA-43160-****
SEE SDA-43160-****
SEE SDA-43160-****
SEE SDA-43160-****
SEE SDA-43160-****
MALE TAB CRIMP TERMINAL, SMALL
MALE TAB CRIMP TERMINAL, LARGE
MALE TAB CRIMP TERMINAL, SIDE/SIDE DOUBLE CRIMPS
FEMALE CRIMP TERMINAL, SMALL
FEMALE CRIMP TERMINAL, LARGE
43178-1001
43178-2001
43178-3001
43375-0001
43375-1001
(2) Custom Connector Housings:
These connector housings are molded from 66 nylon in its natural color, translucent white, unless
otherwise indicated. The flammability classification for each connector housing listed below is UL94V-2
PRODUCT NAME:
MATERIAL NUMBER:
3 CIR. PLUG HOUSING (SPECIAL POLARIZATION – COLOR = RED)
43180-0013
3 CIR. PLUG HOUSING (SPECIAL POLARIZATION – COLOR = BLACK)
43180-0023
6 CIRCUIT SWITCH HOUSING (UL94V-2)
43168-1006
24 CIRCUIT APPLIANCE TIMER HOUSING (UL94V-2)
43275-1024
3 CIRCUIT SWITCH HOUSING (UL94V-2)
43301-1003
24 CIR. APPLIANCE TIMER HOUSING (UL94V-2 – COLOR = BLACK)
43796-1024
3 CIR. 7.50 mm HOUSING (CENTER CIRCUIT IS VOIDED)
43335-1103
3 CIR. 7.50 mm HOUSING (SPECIAL POLARIZATION – COLOR = RED)
43335-3013
3 CIR. 7.50 mm HOUSING (SPECIAL POLARIZATION – COLOR = BLUE)
43335-4023
3 CIR. 7.50 mm HOUSING (SPECIAL POLARIZATION – COLOR = BLACK) 43335-5023
REVISION:
4
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
2 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
SEE PRODUCT DRAWING
4.0 RATINGS
4.1 VOLTAGE
600 volts
Also, 1000 volts, mated, for the standard 7.50 mm (.295”) centerline types (wire to wire only)
Note that this value reverts to 600 volts when the system is not mated; before disconnecting a
connector used with a higher potential than 600 volts, the effected leads must be discharged to
either ground or to the chassis.
4.2 CURRENT AND APPLICABLE WIRES
WIRE SIZE – TYPE
18 AWG – UL 1015
16 AWG – UL 1015
14 AWG – UL 1015
CURRENT LEVEL
12 AMPERES MAXIMUM
TBD AMPERES MAXIMUM
15 AMPERES MAXIMUM
4.3 TEMPERATURE
-40o centigrade to +75o centigrade
5.0 PERFORMANCE
5.1 ELECTRICAL REQUIREMENTS
ITEM
REVISION:
4
TEST CONDITION
REQUIREMENT
VOLTAGE
DROP
THE VOLTAGE DIFFERENCE BETWEEN AN
UNINTERRUPTED 6” LENGTH OF #18 AWG (UL1015)
WIRE, AND THE SAME 6” LENGTH THAT IS
INTERRUPTED BY TWO CRIMPED TERMINALS THAT
ARE MATED AND HAVE 12.0 AMPERES CURRENT
FLOWING. (SEE SHEETS 6 & 7)
0.120 VOLTS
MAX (INITIAL)
INSULATION
RESISTANCE
MATE CONNECTORS WITH A VOLTAGE OF 500
VDC BETWEEN ADJACENT TERMINALS AND
BETWEEN TERMINALS AND GROUND.
1000 MEGOHMS
MIN (INITIAL)
DIELECTRIC
WITHSTANDING
VOLTAGE
MATE CONNECTORS WITH A VOLTAGE OF 5000
VAC FOR 1 MINUTE
NO
BREAKDOWN
CONTACT
RESISTANCE
(LOW LEVEL)
MATE CONNECTORS WITH A MAXIMUM VOLTAGE
OF 20 MV AND A CURRENT OF 100 MA.
10.0 MOHMS
MAX
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
3 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.2 MECHANICAL REQUIREMENTS
ITEM
TEST CONDITION
REQUIREMENT
CONNECTOR
MATING &
UN-MATING
FORCE
INSERT AND WITHDRAW CONNECTORS AT
A RATE OF 25 +/- 6 mm (1 +/- .250 INCHES)
PER MINUTE
MAX
MIN
INSERT
WITHDRAW
(3.0 LBS)
(0.5 LBS)
PER TERMINAL
TERMINAL
RETENTION
FORCE IN
HOUSING
AXIAL PULL OUT FORCE ON THE TERMINAL
IN THE HOUSING AT A RATE OF 25 +/- 6 mm
(1 +/- .25 INCHES) PER MINUTE
(RECEPTACLE TERMINAL)
TERMINAL
RETENTION
FORCE IN
HOUSING
AXIAL PULL OUT FORCE ON THE TERMINAL
IN THE HOUSING AT A RATE OF 25 +/- 6 mm
(1 +/- .25 INCHES) PER MINUTE
(MALE TAB CRIMP TERMINAL)
VIBRATION
AMPLITUDE: 1.50 mm (.060 IN.) PEAK-TO-PEAK CONTACT RESISTANCE
SWEEP: 10-55-10 HZ IN ONE MINUTE
10.0 MOHMS MAX
DURATION: 2 HOURS IN EACH X-Y-Z AXIS
NO DISCONTINUITY
GREATER THAN ONE
MICROSECOND
MECHANICAL
SHOCK
50 G IN THE FORM OF THREE SAW TOOTH
WAVEFORM SHOCKS IN EACH X-Y-Z AXIS.
20 LBS MIN
(TPA NOT ACTIVATED)
25 LBS MIN
(WITH TPA ACTIVATED)
30 LBS MIN
(TPA NOT ACTIVATED)
30 LBS MIN
(WITH TPA ACTIVATED)
CONTACT RESISTANCE:
10.0 MOHMS MAX
NO DISCONTINUITY
GREATER THAN ONE
MICROSECOND
REVISION:
4
WIRE PULL
OUT FORCE
(AXIAL)
APPLY AN AXIAL PULL OUT FORCE ON THE
WIRE AT A RATE OF
25 +/- 6 mm (1 +/- .250 INCHES) PER MIN.
TERMINAL
INSERTION
FORCE
APPLY AN AXIAL INSERTION FORCE ON
THE WIRE AT A RATE OF
25 +/- 6 mm (1 +/- .250 INCHES) PER MIN.
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
AWG
14
16
18
MIN FORCE
50 LBS
45 LBS
30 LBS
1.5 LBS MAX
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
4 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
5.3 ENVIRONMENTAL REQUIREMENTS
ITEM
TEST CONDITION
THERMAL
SHOCK
MATED CONNECTORS TO BE EXPOSED TO 25
CYCLES OF:
TEMPERATURE (DEGREES C)
-55 +0/-3
+85 +3/-0
HUMIDITY
(STEADY
STATE)
REQUIREMENT
DURATION (MIN.)
30 +3/-0
30 +3/-0
MATED CONNECTORS TO BE EXPOSED TO A
TEMPERATURE OF 85 +/- 2 DEGREES C WITH A
RELATIVE HUMIDITY OF 90 TO 95% FOR 96
HOURS.
APPEARANCE:
NO DAMAGE
CONTACT
RESISTANCE:
10.0 MOHMS MAX
APPEARANCE:
NO DAMAGE
CONTACT
RESISTANCE:
10.0 MOHMS MAX
DIELECTRIC
STRENGTH:
NO BREAKDOWN
INSULATION
RESISTANCE:
1000 MEGOHMS MIN
HUMIDITY
(CYCLIC)
MATED CONNECTORS TO BE EXPOSED TO
TEMPERATURE/HUMIDITY CYCLING BETWEEN
+250 C AND +650 C AT 95% RH, -100 C WITH
HUMIDITY NOT CONTROLLED.
(MIL-STD-1344A METHOD 1002.2)
(TYPE II)
APPEARANCE:
NO DAMAGE
CONTACT
RESISTANCE:
10.0 MOHMS MAX
DIELECTRIC
STRENGTH:
NO BREAKDOWN
INSULATION
RESISTANCE:
100 MEGOHMS MIN
6.0 PACKAGING
SEE PRODUCT DRAWING
7.0 GAGES AND FIXTURES
PICTORIALS & SPECIFICATIONS ARE PROVIDED AS NEEDED
REVISION:
4
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
5 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
8.0 OTHER INFORMATION
Voltage Drop, and Cycling Test:
Do this test with mated housings (43335-1003 and 43180-1003) both fully loaded with their respective
terminals (43375-0001 and 43178-0001). Each terminal shall be crimped to a twelve inch length of
#18 AWG, UL1015 wire with white insulation.
The mated connector housings shall lie latch side up and flat atop the test bench, lined up, side by
side, and spaced 76.2 mm (3.0”) apart. The wires shall be lifted 3.18 mm – 12.70 mm (.125” - .500”)
above the test bench. Heat sinks (eg. metal nuts and bolts), and heat sources are to be kept far
enough away from the test samples so that the connector temperatures are not effected. The wires
are to be connected end to end in daisy chain form with the stripped conductor ends twisted together
and soldered. See figure #2.
For each mated pair of connector housings there are three wire taps. The wires used in the center
position of the mated connector housings (circuit #2) are to be stripped for the voltage taps. See
figure #1.
Cycle Test: The mated connector assemblies to be subjected to a 500 hour cycling test comprised of
a 45 minute “on” period and 15 minute “off” period. During each “on” period 12.00 +/-0.10 amperes
shall be present in the wires of the mated connector housings being tested. During each “off” period,
0.00 amperes to be present (ie. shut off). The voltage data is to be recorded during the last 10
minutes of the “on” period of the specified cycle.
The criterion, voltage drop, is the arithmetic difference between the voltage across the termination
(“A”), and the voltage across the uninterrupted 6” length of wire (“B”). The voltage data to be recorded
every twenty four cycles, and at the five hundredth cycle.
Requirement: 0.120 volts maximum throughout the test.
REVISION:
4
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
6 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
REVISION:
4
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
7 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
PRODUCT SPECIFICATION
LTR
“1”
“2”
“3”
4
REVISION:
4
REVISIONS
“X” RELEASE PER ECN# U50791
REVISED PER ECN# U81258
REVISED PER ECN# U81679
ADDED P/N, CONVERTED TO WORD; ECN: UCP2005-2735
ECR/ECN INFORMATION:
EC No: UCP2005-2735
DATE: 06/07/2005
DOCUMENT NUMBER:
PSX-43335-9999
TITLE:
95/02/14
97/11/25
98/02/19
05/06/08
KBP
KBP
KBP
JBL
SHEET No.
PRODUCT SPECIFICATION
APPLIANCE APPLICATIONS
3.18/(.125) X 0.51/(.020) FLAT BLADE SYSTEM-TPA
8 of 8
CREATED / REVISED BY:
CHECKED BY:
APPROVED BY:
J.LOWE
A.DERR
F.SMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
