43914-1104

12 11 10 DIM. A DIM. B 30.90/[1.217] 40.90/[1.610] 50.90/[2.004] 60.90/[2.398] 70.90/[2.791] 30.90/[1.217] 40.90/[1.610] 50.90/[2.004] 60.90/[2.398] 70.90/[2.791] 45.70/[1.799] 55.70/[2.193] 65.70/[2.587] 75.70/[2.980] 85.70/[3.374] 45.70/[1.799] 55.70/[2.193] 65.70/[2.587] 75.70/[2.980] 85.70/[3.374] MATERIAL NUMBER CIRCUITS H G 43914-1001 43914-1002 43914-1003 43914-1004 43914-1005 43914-1101 43914-1102 43914-1103 43914-1104 43914-1105 6 8 10 12 14 6 8 10 12 14 9 8 7 5 6 POLARIZING WEBS PRESENT QTY. 0 NO 0 NO 0 OBSOLETE NO 0 NO 0 NO 1 YES 2 YES 2 YES 2 YES 2 YES 4 3 2 1 NOTES: 1. 2. 3. 4. MATERIAL : POLYESTER, U.L. 94V-0. COLOR: BLACK PRODUCT SPEC.: PS-42815-001 USES STANDARD 42815 MINI-FIT SR. FEMALE CRIMP TERMINALS. EACH WIRE MUST BE DRESSED SUCH THAT THE TERMINAL MAINTAINS ITS FREE FLOAT WITHIN THE HOUSING. 5. TPA #43980 MUST ALWAYS BE USED WITH THIS CONNECTOR. 6. PART MATES WITH MOLEX HEADER 43915. 7. POLARIZING WEBS TO BE LOCATED BETWEEN CIRCUITS ON EITHER END OF HOUSING OF THE CIRCUIT 1 ROW AS SHOWN. EXCEPTION: THE 6 CIRCUIT HOUSING WILL HAVE A SINGLE WEB ON THE CIRCUIT 1 END. H G ANTI-OVERSTRESS FEATURE F STEP 1. TERMINALS ARE TO BE ORIENTATED AND LOADED INTO HOUSING AS SHOWN. F TERMINAL LATCH TERMINAL WALL FORWARD STOP 10.00 ±0.13 TYP. .394 ±.005 A ±0.50 [±.020] E E B ±0.95 [±.037] STEP 2. TERMINALS ARE LOADED WHEN SEATED AGAINST FORWARD STOP AND TERMINAL LATCHES ARE SNAPPED BEHIND TERMINAL WALLS. RETENTION FORCE AT THIS STAGE = 0.5 Kg. CIRCUIT #1 DESIGNATION ENGRAVED NUMBER AND RIB 12.40 ±0.20 .488 ±.008 POLARIZING WEBS (2 PLACES) (SEE CHART AND NOTE 7) D D 1 20.80 ±0.50 .819 ±.020 C C 34.40 ±0.20 1.354 ±.008 RETENTION STRAP BREAK-OFF TAB FACING FORWARD RETENTION RAMP * THIS PRODUCT MUST NEVER BE USED WITHOUT THE T.P.A * 3.50 ±0.25 .138 ±.010 B B 2017/12/20 2018/01/17 2018/01/17 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 169759 ME SGANGADHARDO ISHWARG 24.80 ±0.90 .976 ±.035 T.P.A SHOWN INSTALLED STEP 3. AFTER TERMINALS ARE LOADED INTO HOUSING, T.P.A. IS TO BE "BROKEN OR CUT" IN HALF, ORIENTATED AND INSTALLED IN THE DIRECTION SHOWN UNTIL THE RETENTION STRAPS SNAP OVER THE RETENTION RAMPS. THIS PRODUCT MUST NEVER BE USED WITHOUT THE INSTALLATION OF THE T.P.A 12 P1 RELEASE DATE 11 2018/01/17 G 12:09:56 10 9 8 7 6 REV RELEASE STATUS FORMAT: Eng-lega-master-tb-prod-C REVISION: C DATE: 2017/02/06 EC NO: DRWN: CHK'D: APPR: A 5 DIMENSION UNITS GENERAL TOLERANCES (UNLESS SPECIFIED) INCH MM 2:1 MM/[INCH] DRWN BY 4 PLACES ± ± COMERCI 3 PLACES ± ± CHK'D BY 2 PLACES ± ± COMERCI 1 PLACES ± ± APPR BY 0 PLACES ± ± ANGULAR TOL ± SCALE FRY DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS DATE 1997/08/20 1997/08/25 DATE PRODUCT CUSTOMER DRAWING 1997/08/26 THIRD ANGLE PROJECTION C 4 RECEPTACLE HOUSING DUAL ROW 6-14 CIRCUIT (MINI-FIT SR.) DATE MATERIAL NUMBER SERIES 43914 SEE CHART DOCUMENT NUMBER GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER SD-43914-002 3 CUSTOMER 2 PSD 001 1 OF 1 1 A