501193-3000

10 9 7 8 6 5 4 3 2 1.07 0.96 1.25 F 0.98 F ⌀ 1.5 1 SECTION B-B SECTION A-A NOTES: 1. 適合ハウジング: 501189**** E APPLICABLE HOUSING 4 CONTACT POINT 1.75 2. めっき仕様：表題欄参照 1.7 PLATING:SEE TABLE (GOLD PLATING) 0.65 3. 本製品はコンタクト部 金めっき品である。 0.55 0.78 A THIS PRODUCT IS GOLD PLATING FOR CONTACT POINT. B 4. 本製品はバレル外面 錫めっき品である。 THIS PRODUCT IS TIN PLATING OUTSIDE A BARREL. (0.12) 1.3 D 0.28 A CONTACT POINT E 501330**** 501939**** D 5. 圧着条件については、 圧着仕様書(CS-501193-001)を参照願います。 PLEASE REFER TO CRIMP SPECIFICATION (CS-501193-001). 6. 製品の取扱いについては、コネクタ取扱い 説明書(5013300000 PS A00,A01) を参照願います。 PLEASE REFER TO INSTRUCTION MANUAL(5013300000 PS A00,A01). B OUTSIDE OF BARREL (GOLD PLATING) (TIN PLATING) C C TREAD MARK Z 0.76μm MIN. MXJ 1.27μm MIN. VIEW Z 0.9μm MIN. 0.38μm MIN. 1.0μm MIN. 0.1μm MIN. 5011935100 5011935000 5011936100 5011936000 5011933000 連鎖状 CHAIN 下地：ニッケルめっき バレル外側：錫めっき 接点部：金めっき UNDER PLATING: OUTSIDE OF BARREL: CONTACT AREA： オーダー番号 NICKEL PLATING TIN PLTAING GOLD PLATING ODER NO. めっき仕様(前めっき) : PLATING(PRE-PLATING) B MATERIAL りん青銅　下地ニッケル、部分金めっき、錫めっき品 PHOSPHOR BRONZE t=0.12, SELECTIVE GOLD PLATING, SELECTIVE TIN PLATING, UNDER NICKEL PLATING FINISH 　　　　　　　　　SEE NOTE WIRE RANGE 　　　　　　　　　AWG#28-32 INS. RANGE 　　　　　　　　　⌀0.4-0.8 A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 10 P1 RELEASE DATE 9 2022/02/28 11:54:54 8 7 6 5 バラ状 LOOSE 連鎖状 CHAIN バラ状 LOOSE 連鎖状 CHAIN B 端子形状 FORM THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 20:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509451 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 EC NO: 686785 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: QHE31 APPR: TKANEKO THIRD ANGLE PROJECTION 2021/09/07 2022/02/28 2022/02/28 PICO-CLASP 1.0 W/B CONN CRIMP REC TERM (GOLD PLATING) PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2017/04/03 2017/04/06 DRAWING SERIES A3-SIZE 501193 3 5011930000 MATERIAL NUMBER CUSTOMER SEE TABLE PSD 000 C1 SHEET NUMBER 1 OF 1 2 1 A