5017835009

10 9 7 8 5 6 4 3 2 1 B F F NOTES C 1. 適合プラグジャケットカバー：501784-**09 APPLICABLE PLUG JACKET COVER : 501784-**09 2. 材質 MATERIAL PBT, UL94V-0, 色：黒色 PBT, UL94V-0, COLOR: BLACK E E A D 8 (A) E 3.3 D 2.6 2.87 1.15 D C C 41.2±0.3 26.2±0.25 B 42.16±0.3 42.46±0.3 43.96±0.3 44.08±0.3 27.16±0.25 27.46±0.25 28.96±0.25 29.08±0.25 D E C A B 501783-8009 501783-5009 PLASTIC BAG PACKAGE 80 50 B 極数 オーダー番号 ORDER NO. CIRCUITS CONNECTOR SERIES No. 501783-**09 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 6.8 DIMENSION UNITS SCALE mm 5:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2021/12/17 ± 1.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 09:47:02 8 ANGULAR TOL 7 6 5 4 0.5 FFC TO BOARD CONN. PLUG JACKET EC NO: 688327 DRWN: TNAKAGAWA01 CHK'D: TKON APPR: SHOSHIKAWA INITIAL REVISION: DRWN: TNAKAGAWA01 APPR: SHOSHIKAWA THIRD ANGLE PROJECTION 2021/06/04 2021/12/17 2021/12/17 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/03/09 2021/03/15 DRAWING SERIES A3-SIZE 501783 3 5017832000-SD MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 000 B SHEET NUMBER 1 OF 2 1 A 10 9 8 7 5 6 4 3 2 1 F F 0.5X(N-1)+2.6 ±0.04 1.3±0.06 1.9 +0.5 -0.3 0.5X(N-1) ±0.06 NOTES 0.3±0.03 0.5±0.03 3 このFFC推奨寸法はシールド無しのRec Assy. に適用。表を参照。 THIS FFC RECOMMENDED DIMENSION IS APPLICABLE ON REC ASSY WITHOUT SHIELD. REFER TO TABLE. (PITCH) R 0.2±0.05 5017848009 80 501864 SERIES 501786 SERIES WITHOUT SHIELD 5017845009 50 501864 SERIES 501786 SERIES WITHOUT SHIELD RIGHT ANGLE VERTICAL APPLICABLE PLUG TYPE CIRCUIT JACKET COVER APPLICABLE REC. ASSY 9.2±0.3 8±0.07 4.45±0.07 7.7±1 (補強板長さ) E X 1.3±0.06 E R 0.25 ±0.05 R 0.2±0.05 0.5X(N+1) ±0.05 D D ⌯ 0.03 X 0.5X(N-1)+5 ±0.2 3 コネクタ接点部 適合FFC推奨寸法 APPLICABLE FFC RECOMENDED DIMENSION （仕上がり厚さ：コネクタ接点部 0.3±0.03） C C FFCについて　ABOUT FFC 　打ち抜き方向は導体側から補強板側を推奨します。 　導体部については軟箔銅35μmまたは50μmを推奨します。 　FFCに規定された定格温度がFFC単体前提である場合が御座います。 　コネクタと組み合わせての実使用において、接着層が劣化するなどの信頼性を満足できないケースを回避 　するため、実機での評価/確認をお願いいたします。 　RECOMMENDED PUNCHING DIRECTION : FROM CONDUCTOR SIDE TO STIFFENER SIDE 　RECOMMENDED CONDUCTOR SPEC : SOFT COPPER FOIL 　RECOMMENDED CONDUCTOR THICKNESS : 35 MICROMETER OR 50 MICROMETER 　NOTE : WHEN ACTUALLY USING IT WITH CONNECTOR, PLEASE DO THE EVALUATION AND THE 　 CONFIRMATION WITH AN ACTUAL EQUIPMENT TO EVADE THE CASE WHERE RELIABILITY 　 CANNOT BE FILLED (THE ADHESIVE LINE OF FFC IS DETERIORATED ETC.) B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 1:1 CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2021/12/17 ± 1.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 09:47:02 8 ANGULAR TOL 7 6 5 4 0.5 FFC TO BOARD CONN. PLUG JACKET EC NO: 688327 DRWN: TNAKAGAWA01 CHK'D: TKON APPR: SHOSHIKAWA INITIAL REVISION: DRWN: TNAKAGAWA01 APPR: SHOSHIKAWA THIRD ANGLE PROJECTION 2021/06/04 2021/12/17 2021/12/17 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2021/03/09 2021/03/15 DRAWING SERIES A3-SIZE 501783 3 5017832000-SD MATERIAL NUMBER CUSTOMER SEE SHEET 1 2 GENERAL PSD 000 B SHEET NUMBER 2 OF 2 1 A