501820-3231

18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 4 L L 3 K K 2 NOTES: VALID UNLESS OTHERWISE SPECIFIED 1. GENERAL: B 1.1 MATING CONNECTOR INFORMATION REFER TO MOLEX SD-64319-001 1.2 APPLICATION SPECIFICATION SEE: 5018203231-AS 1.3 PRODUCT SPECIFICATION SEE: 5018203231-PS 1.4 HEADER INTERFACE DRAWING REFER TO MOLEX DWG SD-98644-006 1.5 PACKAGING SPECIFICATION PER MOLEX DRAWING 5018209000-PK 1.6 DATA MUST BE SUBMITTED UNDER THE MOLEX PART NUMBER TO IMDS (COMPANY ID#13255) J 7 H J H 2. DESIGN - MATERIALS: SEE ASSEMBLY PART LIST TABLE 3. DESIGN - GEOMETRY: 3.1 THE 3-D CAD DATA IS BASIC (WITHOUT TOLERANCE) AND MUST BE TAKEN FROM THE DATA FILE AT ITS LATEST REVISION. 3.2 THE 3-D CAD DATA IS MASTER FOR THIS PART AND IS TO BE USED TO ESTABLISH DIMENSIONAL INFORMATION NOT SHOWN ON THIS DRAWING. ANY DIMENSIONS UNDERLINED INDICATE A CONFLICT WITH THE MODEL. 3.3 PRODUCT DESIGN MODEL NUMBER(S): 501820323X CUSTOMER MODEL FROM MOLEX PLM SYSTEM. 3.4 GENERAL TOLERANCE SEE TITLE BLOCK. 3.5 LASER MARKING TEXT, FONT: ARIAL, SIZE 4mm G 1 C F G 4. DESIGN - MANUFACTURING: 4.1 SHIPPED PARTS WITH GASKET ASSEMBLED. 4.2 ALIGNMENT PLATE IN PRE-LOCK POSITION DURING DELIVERY. F C 622486 2019/8/16 Page1: Notes: Remove 4.1 ANY PROCESS LUBRICANT REMAINING ON THE TERMINAL MUST NOT VARNISH OR DEGRADE ITS ELECTRICAL PERFORMANCE AS DEFINED IN THE PRODUCT SPEC. PROCESS LUBRICANTS SHALL BE APPROVED BY THE RESPONSIBLE ENGINEER. Page2: Notes: Revise the 5th notes for screw torque recommendation B1 612043 2019/2/14 RELEASE FOR GENERAL MARKET NO MODIFICATION FOR CONTENT 2018/9/10 Add header coding table on pg2. Revise laser marking content definition. Revise note for screw torque recommendation. Revise panel recommendation layout: 10.75±0.1 was 10.4±0.1 7.6±0.1 was 7.2±0.1 16.25±0.1(2x) was 16.1±0.1(2x) add radius R1.0 MAX (4x) see revision marker B for changes 6 E 5 D E D B C 603954 ASSEMBLY PART LIST ITEM NO. DESCRIPTION QTY/ASSY MATERIAL COLOR A 600397 2018/6/11 1 HOUSING 1 PBT G.F. GRAY REVISION ECTR # DATE 2 GASKET 1 SILICONE RED BROWN 3 SECONDARY LOCKING 1 PBT G.F. BLACK ALIGNMENT PLATE 1 PBT G.F. GREEN 5 REAR SEAL COVER 1 PBT G.F. GREEN 6 MAT SEAL 1 SILICONE BLUE 7 4 COIL SPRING SYMBOLS = 0 = 0 = 0 FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 P1 RELEASE DATE 17 16 2019/08/22 04:17:29 15 14 13 12 11 10 9 8 CURRENT REV DESC: INITIAL RELEASE B GENERAL TOLERANCES (UNLESS SPECIFIED) ± = 0 3 PLACES ± = 0 2 PLACES ± 1 PLACE ± 0.2 0 PLACES ± 0.2 = 0 7 2:1 4 PLACES = 0 C mm = 0 = 0 INSPECTION BALLOON NUMBERS LOG 9 THE LAST BALLOON NUMBER USED THE BALLOON NUMBER ADDED THE BALLOON NUMBER REMOVED SCALE ± A DOCUMENT STATUS DESCRIPTIONS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL / STAINLESS STEEL INITIAL RELEASE REVISION LOG B 4 C 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 EC NO: 622486 DRWN: NPENG01 CHK'D: HWBAI APPR: JDENG02 INITIAL REVISION: DRWN: HWBAI APPR: CBQIU THIRD ANGLE PROJECTION 2019/08/16 2019/08/21 2019/08/22 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER A 2018/05/23 2018/07/04 DRAWING SERIES A1-SIZE 501820 5 SALES DARWING CMC 32P PANEL MOUNT HEADER 4 5018203231-SD MATERIAL NUMBER SEE TABLE 3 PSD 000 CUSTOMER GENERAL MARKET 2 C SHEET NUMBER 1 OF 2 1 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 L L �20.2� �16.1� ALIGNMENT PLATE SHOWN IN DELIVERY POSITION TO BE LOCKED ON 2 LATCHES SECONDARY LOCKING TO BE LOCKED ON 4 LATCHES PRE-LOCK POSITION IN DELIVERY K K J J SECTION A-A REAR SEAL COVER TO BE LOCKED FULLY ON 4 LATCHES H 14.50 ±0.20 H PANEL LAYOUT RECOMMENDATION 1 41.0 MANUFACTURING DATE YYDDD (YEAR+JULIAN DATE) SEE NOTE 3.5 2x 20.5 18123 501820323X �40.25� ⏥ 0.2 B 10.75 ±0.1 4x R 4.70 ±0.05 G 4x R 1.0 MAX B 2x 20.5 MATING SURFACE �24.9� 2 3 33.50 MAX +0.2 30.6 -0.1 E 16.25 ±0.1 2x 15.2 MATERIAL NO. SEE NOTE 3.5 B X=1,2,3,5 REFER TO CODING 25.5 +0.2 -0.0 F F B 16.25 ±0.1 WHITE LINE MARKING ON EACH SIDE OF CONNECTOR 30.4 B 2x 15.2 �54.75� G E B 4x ⌀ 4.40 ±0.05 4 D D COLOR (RCPT TPA) DIM. A DIM. B DIM. C DIM. D STATUS 5018203231 1 BLACK 9.1 4.3 5.9 4.3 RELEASED TBD 2 GREY 7.5 5.9 9.1 5.9 NOT TOOLED TBD 3 BROWN 5.9 7.5 9.1 9.1 NOT TOOLED TBD 5 BLUE 4.3 7.5 5.9 5.9 NOT TOOLED 5 A A C +0.0 -0.1 B 6 NOTES: 1. MATERIAL: STAINLESS STEEL OR ALUMINIUM. 2. REQUIRED MATING SURFACE FINISH: Ra 3.0μm MAX OR POLISHED 3. RECOMMENDED PANEL THICKNESS FOR MATING AREA: t=3.0~4.0mm 4. REQUIRED SCREW: NAME: CROSS RECESSED ROUND HEAD SELF-TAPPING SCREW TYPE F SPECIFICATION: ST4.2X13, REFER TO GB/T845-1985 Q2724213 C B 5. RECOMMENDED FASTEN TORQUE: 1.4 N·m, MORE DETAILS REFER TO 5018203231-AS-CH 40.9 C CODING 21.0 ±0.1 HEADER CODING TABLE MOLEX P/N SYMBOLS = 0 = 0 30.0 ±0.1 = 0 FORMAT: master-tb-prod-A1 REVISION: H DATE: 2018/01/18 18 17 16 2019/08/22 04:17:29 15 14 13 12 11 10 9 8 7 2:1 CURRENT REV DESC: INITIAL RELEASE B GENERAL TOLERANCES (UNLESS SPECIFIED) 4 PLACES ± = 0 3 PLACES ± = 0 2 PLACES ± 1 PLACE ± 0.2 0 PLACES ± 0.2 = 0 C mm = 0 = 0 RELEASE DATE SCALE ± = 0 P1 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS ANGULAR TOL 51.5 A DOCUMENT STATUS C 9 8 D +0.0 -0.1 7 A B +0.0 -0.1 2X 30.4 B (4x) 1.0±0.1 x 45° 34.1 +0.2 -0.0 ⌖ ⌀0.05 A B 2X 41.0 A +0.0 -0.1 WHITE LINE MARKING B 7.6 ±0.1 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 6 EC NO: 622486 DRWN: NPENG01 CHK'D: HWBAI APPR: JDENG02 INITIAL REVISION: DRWN: HWBAI APPR: CBQIU THIRD ANGLE PROJECTION 2019/08/16 2019/08/21 2019/08/22 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER A 2018/05/23 2018/07/04 DRAWING SERIES A1-SIZE 501820 5 SALES DARWING CMC 32P PANEL MOUNT HEADER 4 5018203231-SD MATERIAL NUMBER SEE TABLE 3 PSD 000 CUSTOMER GENERAL MARKET 2 C SHEET NUMBER 2 OF 2 1