501951-2010

LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH SCOPE 9(& 2$ 0.5 mm FPC This specification covers the 0.5mm PITCH FPC CONNECTOR series. PRODUCT NAME AND PART NUMBER Material Number Product Name 4X ( X;O Housing Assembly(Straight Type) + 9X Embossed Tape Package For 501951-**19 CIRCUITS (Refer to the drawing) RATINGS Standard Item 50V Rated Voltage(MAXIMUM) [AC( rms)/DC] 0.4A Rated Current (MAXIMUM) -25 Ambient Temperature Range (Operating and Non-operating) +85 *1*2 1 Including terminal temperature rise 2 FPC FPC must be meet temperature range specified in this standard. E E E E E SHEET 1 2 3 4 5 REVISE ON PC ONLY REV. F E 6 REVISED J2008-1927 ’07/11/15 Y.TAKAYASU REV. DESCRIPTION STATUS DESIGN CONTROL J DOCUMENT NUMBER PS-501951-002 F F F 7 8 9 TITLE: F 10 F 11 0.5 mm PITCH FPC CONN. EASY ON / STRAIGHT (GOLD) THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION WRITTEN BY: CHECKED BY: APPROVED BY: TR.SUZUKI H.HIRATA M.SASAO DATE: YR/MO/DAY 2006/08/31 FILE NAME PS501951002.doc SHEET 1 OF 11 EN-37(019) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH PERFORMANCE . Electrical Performance Item 4-1-1 Test Condition FPC 20mV 10mA (JIS C5402 5.4) Mate applicable FPC and measured by dry circuit, 20mV MAXIMUM, 10mA MAXIMUM. (JIS C5402 5.4) FPC DC 500V Contact Resistance $ D/P   4-1-2 Insulation Resistance Dielectric Strength . 40 milliohm MAX. $ D/P (JIS C5402 5.2/MIL-STD-202 302) Mate applicable FPC together and apply 500V DC between adjacent terminal and ground. (JIS C5402 5.2/MIL-STD-202 Method 302) FPC AC 250V 1 (JIS C5402 5.1/MIL-STD-202 301) Mate applicable FPC, apply 250V AC for 1 minute between adjacent terminal or ground. (JIS C5402 5.1/MIL-STD-202 Method 301) $ D/P   4-1-3 Requirement 50 egaohm MIN. $ D/P No Breakdown Mechanical Performance Item 4-2-1 FPC FPC Retention Force 4-2-2 Terminal/Housing Retention Force &J $ 25±3 mm Insert the actuator, pull the FPC at the speed rate of 25±3mm per minute. 25±3mm Apply axial pull out force on the terminal assembled in the housing at the speed rate of 25±3mm per minute. Fitting Nail/Housing Retention Force 4-2-3 Test Condition FPC 25±3mm Apply axial pull out force on the fitting nail assembled in the housing at the speed rate of 25±3mm per minute. REVISE ON PC ONLY F SEE SHEET 1 OF 11 REV. DESCRIPTION DOCUMENT NUMBER PS-501951-002 Requirement 6 Refer to paragraph 6 1.0N { 0.1kgf } MIN. 1.0N { 0.1kgf } MIN. TITLE: 0.5 mm PITCH FPC CONN. EASY ON / STRAIGHT (GOLD) THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 2 OF 11 EN-37-1(019) PS501951002.doc LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH Environmental Performance and Others Item &J $ &J $ 4-3-1 Repeated Actuator Insertion / Withdrawal Test Condition 1 10 20 Requirement Open and shut actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. Contact Resistance 60 milliohm MAX. FPC 2$ 4-3-2 Temperature Rise 4-3-3 (UL 498) Mate applicable FPC and measure the temperature rise of contact when the maximum AC rated current is passed. (UL 498) DC 1mA 3 10~55~10Hz/ 0.75mm 2 (JIS C60068-2-6/MIL-STD-202 201) Mate applicable FPC and subject to the following vibration conditions, for a period of 2 hours in each of 3 mutually perpendicular axes, passing DC 1mA during the test. Vibration Harf-Amplitude : 0.75mm P-P Frequency : 10-55-10 Hz shall be traversed in 1 minute. (JIS C60068-2-6/MIL-STD-202 Method 201) DC 1mA 2 6 490m/s {50G} 3 Temperature Rise 30 °C MAX. Appearance No Damage Contact Resistance Discontinuity Appearance (JIS C60068-2-27/MIL-STD-202 4-3-4 Shock F SEE SHEET 1 OF 11 REV. DESCRIPTION DOCUMENT NUMBER PS-501951-002 1.0 microsecond MAX. No Damage 213) Mate applicable FPC and subject to the following shock conditions. 3 times of shocks shall be applied for each 6 directions along 3 mutually perpendicular axes, passing DC 1mA current during the test. (Total of 18 shocks) Test pulse : Half Sine 2 Peak value : 490m/s {50G} Duration : 6 milliseconds (JIS C60068-2-27/MIL-STD-202 Method 213) REVISE ON PC ONLY 60 milliohm MAX. Contact Resistance Discontinuity 60 milliohm MAX. 1.0 microsecond MAX. TITLE: 0.5 mm PITCH FPC CONN. EASY ON / STRAIGHT (GOLD) THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 3 OF 11 EN-37-1(019) PS501951002.doc LANGUAGE PRODUCT SPECIFICATION Item 96 4-3-5 Heat Resistance Test Condition FPC 85±2 1 2 Cold Resistance 4-3-7 Humidity (JIS C60068-2-1) Mate applicable FPC and expose to -40±2 degree C for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C60068-2-1) FPC 60±2°C 90 95% 96 1 2 (JIS C60068-2-3/MIL-SDT-202 103) Mate applicable FPC and expose to 60±2 °C, relative humidity 90 to 95% for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C60068-2-3/MIL-SDT-202 Method103) REVISE ON PC ONLY F SEE SHEET 1 OF 11 REV. DESCRIPTION DOCUMENT NUMBER PS-501951-002 Appearance Contact Resistance No Damage 60 milliohm MAX. -40±2 1 2 96 4-3-6 Requirement (JIS C60068-2-2/MIL-STD-202 108) Mate applicable FPC and expose to 85±2 degree C for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C60068-2-2/MIL-STD-202 Method108) FPC JAPANESE ENGLISH Appearance Contact Resistance Appearance Contact Resistance No Damage 60 milliohm MAX. No Damage 60 milliohm MAX. 4-1-3 Dielectric Strength Insulation Resistance Must meet 4-1-3 20 megaohm MIN. TITLE: 0.5 mm PITCH FPC CONN. EASY ON / STRAIGHT (GOLD) THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 4 OF 11 EN-37-1(019) PS501951002.doc LANGUAGE PRODUCT SPECIFICATION Item Test Condition FPC -55±3°C 30 +85±2°C 30 1  P P  P 4-3-8 Temperature Cycling Salt Spray Requirement  5 3 1 2 (JIS C0025) Mate applicable FPC connectors and subject to the following conditions for 5 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. 1 cycle a) –55±3 °C 30 minutes b) +85±2 °C 30 minutes Transit time shall be with in 3 minutes. (JIS C0025) FPC 35±2°C 5±1% 48±4 (JIS C60068-2-11/MIL-STD-202 4-3-9 JAPANESE ENGLISH 101) Appearance Contact Resistance 60 milliohm MAX. Appearance No Damage 48±4 hours exposure to a salt spray from the 5±1% solution at 35±2°C. (JIS C60068-2-11/MIL-STD-202 Method 101) Contact Resistance 40±2 50±5ppm 24 Mate applicable FPC exposed to 50±5ppm SO2 gas at 40±2 degree C for 24 hours. No Damage 60 milliohm MAX. FPC   4-3-10 Appearance No Damage SO2 Gas Contact Resistance 0.2mm 245±3°C 4-3-11 Solderability 0.2mm 3±0.5 Soldering Time : 3±0.5 seconds Solder Temperature : 245±3°C 0.2mm from terminal tip 0.2mm from fitting nail tip REVISE ON PC ONLY F SEE SHEET 1 OF 11 REV. DESCRIPTION DOCUMENT NUMBER PS-501951-002 60 milliohm MAX. Solder Wetting 95% 95% of immersed area must show no voids, pin holes TITLE: 0.5 mm PITCH FPC CONN. EASY ON / STRAIGHT (GOLD) THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 5 OF 11 EN-37-1(019) PS501951002.doc LANGUAGE PRODUCT SPECIFICATION Item O:R JAPANESE ENGLISH Test Condition Requirement INFRARED REFLOW METHOD O:R INFRARED REFLOW CONDITION 9  250+5/-0 250+5/-0 degree C (Peak temperature) 230 230 degree C MINIMUM 20 40 O:R $ 2 20-40 seconds 90 120 90 seconds 150 No Damage After Twice Reflow 180 (Preheat temperature : 150 – 180 degree C) 4-3-12 N: Resistance to Soldering- Heat TEMPERATURE CONDITION GRAPH Appearance (TEMPERATURE ON BOARD PATTERN SIDE) O:R O:R O:R NOTE: Please check the reflow soldering condition by your own devices beforehand. Because the condition change by the soldering devices, p.c.board, and so on. Soldering iron method 370 400 + 0.2mm 3±1 $ Soldering Time : 3±1 seconds MAX. Solder Temperature : 370-400°C 0.2mm from terminal tip 0.2mm from fitting nail tip Without too much pressure to the terminal pin and fitting nail. No Damage : Reference Standard X