5034290000

9 7 8 5 6 4 3 2 1 NOTES 1 E 図示の斜線部の範囲は、接点部のため 傷、打痕、汚れなどをつけないようにしてください E PLEASE DON'T DAMAGE, DON'T DENT, AND DON'T MAKE IT DIRTY, 1 2.35 MIN. BECAUSE THE RANGE IN THE HATCHING AREA SHOWN IN FIGURE IS THE CONTACT AREA. トレードマーク：MXプラス1文字の製造工場を示すアルファベットにて表示。 ただし"J"はJAPANを示す。(例：MXJ) 3. 適用電線違い： 502579 シリーズ （ケーブルサイズ： AWG #24-28） 2 SIMILAR PRODUCT THAT DIFFERENCE IS APPLICABLE CABLE SIZE: 502579 SERIES (CABLE SIZE: AWG #24-28) D D 6.90 1.75 2.45 3.80 1.16 1.05 0.70 1.16 ±0.40 1.77 ±0.40 Y (0.15) 0.90 Z C C 1.14 0.32 Z Y SECTION Y-Y 1 SECTION Z-Z 2.35 MIN. TRADE MARK 2 B MX□ B ⌀0.7-1.02mm 部品 PART 絶縁被覆外形範囲 INS RANGE 材質 MATERIAL ニッケルめっき(下地)：0.1 micro-meters MIN NICKEL PLATING (UNDER PLATING) DOCUMENT STATUS 9 P1 RELEASE DATE 端子形状 FORM オーダー番号 ORDER NO DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) ターミナル 錫めっき：0.4 micro-meters MIN リフロー処理(前めっき) TERMINAL MATTE TIN REFLOW TREATMENT (PRE-PLATING) FORMAT: tb-prod-A3 REVISION: H DATE: 2018/01/18 適用電線範囲 WIRE RANGE 連鎖状 CHAIN 503429 0000 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION 銅合金 COPPER ALLOY A AWG #26-30 2020/03/03 8 ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 06:59:12 7 ANGULAR TOL 6 5 4 EC NO: 632623 DRWN: MIKEDA01 CHK'D: SAKIYAMA APPR: KOMURAKAMI INITIAL REVISION: DRWN: MIKEDA01 APPR: KOMURAKAMI THIRD ANGLE PROJECTION DRAWING 2019/04/11 2020/02/28 2020/03/03 DOC TYPE DOC PART REVISION 5034290000-SD MATERIAL NUMBER SERIES A3-SIZE 503429 3 PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2019/04/11 2020/03/03 2 A CLIK-MATE 1.5 CRIMP TERMINAL TIN PLATING AWG26-30 5034290000 PSD 000 A SHEET NUMBER CUSTOMER GENERAL 1 OF 2 1 10 9 7 8 5 6 4 3 2 1 F F 適用製品及び各種仕様書 APPLICABLE PRODUCTS AND VARIOUS SPECIFICATIONS 梱包仕様書 PACKING SPECIFICATION PART NUMBER SPECIFICATION NUMBER 503429 **00 SPK-503429-001 E E 適用ハウジング APPLICABLE HOUSING SINGLE TYPE シリーズ番号 SERIES No 502578 SMT TIN PLATING VERTICAL RIGHT ANGLE 適用嵌合相手 MATE WITH シリーズ番号 SERIES No D 502584 製品仕様書 PRODUCT SPECIFICATION 502585 DUAL TYPE シリーズ番号 SERIES No 503149 BOTTOM ENTRY TIN PLATING VERTICAL 503175 503395 5025780002-PS D 5025780003-PS AS-502578-001 適用ハウジング APPLICABLE HOUSING AS-503395-001 C SMT TIN PLATING VERTICAL RIGHT ANGLE 適用嵌合相手 MATE WITH シリーズ番号 SERIES No 503154 503148 製品仕様書 PRODUCT SPECIFICATION 5031490000-PS 5031490001-PS 取扱説明書 APPLICATION SPECIFICATION B 503159 5025780000-PS 取扱説明書 APPLICATION SPECIFICATION C THROUGH HOLE TIN PLATING VERTICAL RIGHT ANGLE B AS-503149-001 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 10 P1 RELEASE DATE 9 2020/03/03 ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.2 2 PLACES ± 0.2 1 PLACE ± 0.2 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 06:59:12 8 ANGULAR TOL 7 6 5 4 EC NO: 632623 DRWN: MIKEDA01 CHK'D: SAKIYAMA APPR: KOMURAKAMI INITIAL REVISION: DRWN: MIKEDA01 APPR: KOMURAKAMI THIRD ANGLE PROJECTION DRAWING 2019/04/11 2020/02/28 2020/03/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2019/04/11 2020/03/03 SERIES A3-SIZE 503429 3 CLIK-MATE 1.5 CRIMP TERMINAL TIN PLATING AWG26-30 5034290000-SD MATERIAL NUMBER CUSTOMER 5034290000 GENERAL 2 PSD 000 A SHEET NUMBER 2 OF 2 1 A