503566-2102

9 7 8 5 6 4 3 2 1 注記 NOTES E 1. 製品詳細寸法については製品単体図面を参考下さい。 DETAIL DEMENSIONS, SEE PRODUCT DRAWING. 2. 梱包数量：6000個/リール NUMBER OF CONNECTORS : 6000 PCS/REEL 3. リードテープ長さLEAD TAPE LENGTH REEL 引き出し方向 E PULL OUT DIRECTION 100MIN. 引き出し方向 PULL OUT DIRECTION C トップテープリーダー部 TOP TAPE LEADER PART 400MIN. ⌀380±2 (⌀80) D トップテープ接着部（空エンボス） TOP TAPE BONDED PART. (EMPTY) D 末端部（空部） 部品挿入部 TAIL PART COMPONENT (EMPTY) SUPPLIER 160MIN. 4. 材料 MATERIAL ポリスチレン (POLYSTYRENE) キャリアテープ (CARRIER TAPE) トップテープ(TOP TAPE) PET , PE , PEF リール (REEL) ポリスチレン(PS) POLYSTYRENE (PS) C B±1.0 5. トップテープの剥離強度については、IEC60286-3 に準拠 TOP TAPE PEEL FORCE IS DEFINED BY IEC60286-3. 2±0.5 B C B 2016/12/22 2017/02/21 2017/02/21 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 9 P1 RELEASE DATE 21.02.2017 8 05:22:24 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: A 113200 MNISHIKAWA KTAKAHASHI MSASAO ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM NTS DRWN BY DATE 2016/12/22 MNISHIKAWA 2017/02/21 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.3 FPC CONN. E/O TAPING PACKAGE (503566-**08 SERIES) DATE CHK'D BY A DATE 2017/02/21 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503566 GENERAL DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 5035660001 2 PSD 000 1 1 OF 2 7 8 5 6 8±0.1 (PITCH) 3 2 1 (3.9) 引き出し方向 E 4 PULL OUT DIRECTION (2.9) 1.5+0.1 0 Y (0.58) E T (3.9) 0.2±0.05 9 (2.85) 32mm幅テープ 32mm WIDTH TAPE (Ｒ0.75) 32±0.3 D 503566-5102 51 D 503566-4502 45 503566-4302 43 503566-4102 41 503566-3902 39 503566-3702 37 503566-3502 11.5 25.4 35 503566-3302 33 503566-3102 31 C 503566-2702 27 503566-2502 25 503566-2302 23 503566-2102 21 503566-1902 19 503566-1702 17 503566-1502 15 7.5 17.4 503566-1302 13 503566-1102 11 B 9 503566-0902 EMBOSSED TAPE PACKAGE 極　数 C B A オーダー番号　ORDER NO. CIRCUITS CONNECTOR SERIES NO.:503566-**08 28.4±0.25 14.2 24mm幅テープ E (A) 24±0.3 (C) C CENTER OF POCKET 16mm幅テープ エンボスポケット中心 D 24mm WIDTH TAPE 16mm WIDTH TAPE 1.75±0.1 16±0.3 B (0.3) (2) 4±0.1 (1.75) ⌀1.5+0.1 0 Y X X E キャリアテープ幅 累積ピッチ 40±0.2 2016/12/22 2017/02/21 2017/02/21 GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED 9 P1 RELEASE DATE 21.02.2017 8 05:22:24 7 6 5 A REV EC NO: DRWN: CHK'D: APPR: A 113200 MNISHIKAWA KTAKAHASHI MSASAO ANGULAR TOL ± RELEASE STATUS 33.4 17.25 15.45 14.85 14.25 13.65 13.05 12.45 11.85 11.25 10.05 9.45 8.85 8.25 7.65 7.05 6.45 5.85 5.25 4.65 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION SECTION Y-Y FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 D EMBOSSED TAPE WIDTH ACUMULATIVE PITCH：40±0.2 SECTION X-X DETAIL T 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM NTS DRWN BY DATE 2016/12/22 MNISHIKAWA 2017/02/21 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.3 FPC CONN. E/O TAPING PACKAGE (503566-**08 SERIES) DATE CHK'D BY A DATE 2017/02/21 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503566 GENERAL DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 5035660001 2 PSD 000 1 2 2 OF 2 9 7 8 5 6 4 3 2 1 (2.15) （FPC挿入深さ） (INSERTION DEPTH OF FPC) A E キャビティ番号 奇数極端子 金型番号 CL MOLD NO. CAVITY NO. 偶数極端子 (0.65) （接点位置） (CONTACT POSITION) ODD TERMIANL (0.1) (1.3) （接点位置） (CONTACT POSITION) EVEN TERMIANL E ハウジング HOUSING 0.32 (0.1) 0.52 SECTION Y-Y （テール部長さ） (DIMENSION OF SOLDER TAIL) アクチュエータ ACTUATOR SECTION X-X キャビティ番号 D （テール部長さ） (DIMENSION OF SOLDER TAIL) CAVITY NO. トレードマーク 2.85 TRADE MARK 0.3 Y 2.75 X 0.95±0.05 CL （接点間ピッチ） (PITCH OF CONTACTS) C Y X (D) (0.05) 0°) (C) 0.15±0.03 B (PITCH) 0.3 (1.69) 0.6 FITTING NAIL (13 (B) 0.1±0.03 補強金具 0.65 CL 14.4 12.6 12.0 11.4 10.8 10.2 9.6 9.0 8.4 7.2 6.6 6.0 5.4 4.8 4.2 3.6 3.0 2.4 1.8 15.6 13.8 13.2 12.6 12.0 11.4 10.8 10.2 9.6 8.4 7.8 7.2 6.6 6.0 5.4 4.8 4.2 3.6 3.0 E D アクチュエータ開放位置 POSITION OF ACTUATOR OPEN 51 503566-5102 D 45 503566-4502 43 503566-4302 41 503566-4102 39 503566-3902 37 503566-3702 35 503566-3502 33 503566-3302 31 503566-3102 27 503566-2702 C 25 503566-2502 23 503566-2302 21 503566-2102 19 503566-1902 17 503566-1702 15 503566-1502 503566-1302 13 503566-1102 11 B 9 503566-0902 極　数 EMBOSSED PACKAGE C B A オーダー番号 ORDER NO. CIRCUITS CONNECTOR SERIES NO. 503566-**08 16.42 14.62 14.02 13.42 12.82 12.22 11.62 11.02 10.42 9.22 8.62 8.02 7.42 6.82 6.22 5.62 5.02 4.42 3.82 15.0 13.2 12.6 12.0 11.4 10.8 10.2 9.6 9.0 7.8 7.2 6.6 6.0 5.4 4.8 4.2 3.6 3.0 2.4 16.95 15.15 14.55 13.95 13.35 12.75 12.15 11.55 10.95 9.75 9.15 8.55 7.95 7.35 6.75 6.15 5.55 4.95 4.35 2016/12/22 2017/02/21 2017/02/21 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED A 0.6 EC NO: DRWN: CHK'D: APPR: (PITCH) E RELEASE STATUS FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 9 P1 RELEASE DATE 21.02.2017 8 05:22:25 7 6 5 A REV 0.1±0.03 113200 MNISHIKAWA KTAKAHASHI MSASAO ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM NTS DRWN BY DATE 2016/12/22 MNISHIKAWA 2017/02/21 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.3 FPC CONN E/O BTM CONTACT TYPE HGT=0.95MM DATE CHK'D BY A DATE 2017/02/21 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503566 GENERAL DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 5035661001 2 PSD 000 1 1 OF 2 3 0.3±0.05 0.3+0.04 -0.03 0.25±0.05 0.6±0.05 (PITCH) E R0.15±0.05 (PITCH) 0.85±0.05 0.72±0.05 0.03MIN. 0.03MIN. （補強板） (STIFFENER BOARD) 1.7±0.05 TYP.(8) 1.81±0.05 TYP.(2) 1.15±0.05 2.35±0.3 0.3X(N-3)±0.05 0.6±0.05 (PITCH) 熱硬化接着剤 THERMOSETTING ADHESHIVE カバーレイ：ポリイミド（25μm） COVER FILM: POLYIMIDE（25μm） 補強板：ポリイミド STIFFNER BOARD: POLYIMIDE 熱硬化接着剤 THERMOSETTING ADHESHIVE ベースフィルム：ポリイミド（25μm） BASE FILM: POLYIMIDE（25μm） 熱硬化接着剤 THERMOSETTING ADHESHIVE 導体部：銅箔（35μm） COPPER FOIL（35μm） 0.3±0.02 0.3±0.05 (PITCH) 0.3+0.04 -0.03 推奨ペースト厚 推奨マスク開口率 : 100μm : 80% RECOMMEND SCREEN THICKNESS : 100μm RECOMMEND SCREEN OPEN RATIO : 80% 適合するFPC推奨寸法（参考） APPLICABLE FPC PATTERN DIMENSIONS(REF.) 9 ACTUATOR ODD TERMINAL EVEN TERMINAL FITTING NAIL 21.02.2017 8 05:22:25 7 B 2. 端子、補強金具のコプラナリティーは0.1以下とする COPLANALITY OF SOLDER TAILS AND FITTING NAILS: 0.1MAX. 3. 一般公差：± 0.3 GENERAL TOLERANCES: ±0.3 4. ELV AND RoHS COMPLIANT 2016/12/22 2017/02/21 2017/02/21 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION GENERAL TOLERANCES (UNLESS SPECIFIED) RELEASED 113200 MNISHIKAWA KTAKAHASHI MSASAO ANGULAR TOL ± 6 5 A REV RELEASE DATE : LIQUID CRYSTAL POLYMER(LCP), GLASS FILLED 　UL94V-0, NATURAL(WHITE) : POLYAMIDE（PA）, GLASS FILLED 　UL94V-HB, BLACK : PHOSPHOR BRONZE, Gold OVER Nickel PLATING : PHOSPHOR BRONZE, Gold OVER Nickel PLATING : PHOSPHOR BRONZE, Gold OVER Nickel PLATING HOUSING *1 補強板長さが図面通り確保できない場合は、カバーレイと 補強板のオーバーラップ寸法を 0.5mm 以上としてください WHEN STIFFENER BOARD DIMENSION CAN NOT SECURE AS DRAWING, PLEASE GIVE THE OVERLAP SIZE OF COVER FILM AND STIFFENER BOARD AS 0.5mm MINIMUM P1 C 注記NOTES 1.使用材料 MATERIALS ハウジング ：液晶ポリマー（LCP）、ガラス充填、UL94V-0、ナチュラル（白色系） アクチュエータ ：ポリアミド（PA）、ガラス充填、UL94V-HB、黒色 奇数端子 ：燐青銅、ニッケル下地、金メッキ 偶数端子 ：燐青銅、ニッケル下地、金メッキ 補強金具 ：燐青銅、ニッケル下地、金メッキ （端子部仕上がり厚さ：　　　　　） 0.2±0.03 (THICKNESS: 0.2±0.03) RECOMMENDED PUNCHER DIRECTION: FROM CONDUCTOR SIDE TO STIFFENER BORAD SIDE RECOMMENDED MATERIAL: STIFFENER BOARD: POLYIMIDE BONDING AGENT: THERMOSETTING AGENT PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND BECAUSE THERE IS A POSSIBILITY THAT THE EXTRA ADHESIVE CAUSES THE DEFECT IN ELECTRICAL CONTINUITY ・FPCパターンメッキ仕様 金メッキ：0.1μm 以上 下地ニッケルメッキ：2~6μm FPC PATTERN PLATING GOLD PLATING : 0.1μm MINIMUM NICKEL UNDER PLATING : 2~6μm RELEASE STATUS 0.71±0.05 RECOMMENDED PCB PATTERN DIMENSIONS(REF.) ・FPC について (ABOUT FPC) 抜き方向は、導体側から補強板側を推奨します 補強板材質はポリイミド、接着剤は熱硬化接着剤を推奨します なお、接着剤の接点部への付着は導通不良の原因となりますので 染み出しがないよう、お願いします FORMAT: master-tb-prod-A3 REVISION: G DATE: 2015/12/14 D 参考基板レイアウト EC NO: DRWN: CHK'D: APPR: A 0.3X(N-1)±0.05 0.12±0.03 0.6±0.02 FPC構成推奨仕様 STRUCTURE OF FPC B 0.25±0.05 0.3±0.05 0.71±0.05 C 1 3.5±0.5 0.25±0.15 0.85±0.15 0.95±0.15 0.6±0.02 0.3±0.07 R0.15±0.05 (OVERLAP) *1 0.5MIN. D 0.3X(N-1)±0.03 1.5MIN. 端子部メッキ PLATING E 0.3±0.07 0.52±0.05 0.3X(N+1)±0.05 0.2±0.03 仕上がり厚さ THICKNESS 2 0.25±0.05 0.3X(N+1)+1.3±0.05 4 (0.15) 5 6 (0.1) 7 8 (0.15) 9 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE MM NTS DRWN BY DATE 2016/12/22 MNISHIKAWA 2017/02/21 KTAKAHASHI APPR BY MSASAO DRAWING SIZE 0.3 FPC CONN E/O BTM CONTACT TYPE HGT=0.95MM DATE CHK'D BY A DATE 2017/02/21 THIRD ANGLE PROJECTION A3 PRODUCT CUSTOMER DRAWING SERIES MATERIAL NUMBER 503566 GENERAL DOCUMENT NUMBER 3 CUSTOMER DOC TYPE DOC PART SHEET NUMBER 5035661001 2 PSD 000 1 2 OF 2