505070-1422

10 9 7 8 5 6 4 3 2 1 NOTES REEL (⌀80) PULL OUT DIRECTION E 1. RE DETAILED DIMENSION, SEE PRODUCT DRAWING. 2. NUMBER OF CONNECTORS : 8000 PCS/REEL. 3. LEAD TAPE LENGTH. E PULL OUT DIRECTION "D" D F 20PCS. MIN. TOP TAPE BONDED PART. (EMPTY) ⌀380 ±2 F TOP TAPE LEADER PART COMPONENT SUPPLIER 400MIN. B ±1 4. C ±1 5. C 6 TAIL PART (EMPTY) 40MIN. D TOP TAPE PEEL FORCE IS DEFINED BY IEC60286-3 MATERIAL CARRER TAPE :POLYSTYRENE TOP TAPE :PET , OTHER REEL :POLYSTYRENE(PS)(RECYCLE MATERIAL CONTAINED) C Only 6 circuit is different in this dimension. �⌀ 10� �22� 0°� B �12 �2� B (⌀ ) 21 MODEL NO. 505070-**22 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION �⌀ 13� A DOCUMENT STATUS 10 P1 RELEASE DATE 9 2019/02/27 1:5 ANGULAR TOL ± 1.0 ° 4 PLACES ± 0.01 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:28:35 8 SCALE mm GENERAL TOLERANCES (UNLESS SPECIFIED) DETAIL "D" FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 DIMENSION UNITS 7 6 5 4 CURRENT REV DESC: RELEASED EC NO: 612826 DRWN: GSHARMA CHK'D: MSASAO APPR: MSASAO INITIAL REVISION: DRWN: TNISHIDA02 APPR: TKUSUHARA01 THIRD ANGLE PROJECTION DRAWING 2019/02/22 2019/02/27 2019/02/27 2017/03/28 2017/04/03 SERIES A3-SIZE 505070 3 0.35 BB CONN. H=0.6 SSB6 RP PLUG ASSY PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5050700000 MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 007 B SHEET NUMBER 1 OF 3 1 A 10 9 7 8 5 6 4 3 2 1 F F PULL OUT DIRECTION (2.16) 6 (1.08) V TOP TAPE 0.3 ±0.05 (D) SECTION V-V D (E) (A) (7.5) E W E W 1.75 ±0.1 (A) 16 ±0.3 (2.16) (2) V ACCUMULATIVE PITCH 40±0.2 6 ⌀ 1.5 +0.1 0 8 ±0.1 SECTION W-W 4 ±0.1 D C 16 B キャリアテープ幅 CARRIER TAPE WIDTH (E) (D) C B ○ ○ ○ ○ --○ ○ ○ ○ ○ ○ --30 --24 C --22 --20 --18 --16 --14 --12 --10 --8 B --6 HIGH VOL. TOOL LOW VOL. TOOL (A) MATERIAL No. CIRCUIT SAMPLE PREPARATION 505070-3022 505070-2422 505070-2222 505070-2022 505070-1822 505070-1622 505070-1422 505070-1222 505070-1022 505070-0822 505070-0622 6.68 5.63 5.28 4.93 4.58 0.64 1.14 21.4 17.4 4.23 3.88 3.53 3.18 2.78 0.66 1.16 2.43 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 10 FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 9 2019/02/27 ± 1.0 ° 4 PLACES ± 0.01 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:28:35 8 ANGULAR TOL 7 6 5 4 CURRENT REV DESC: RELEASED EC NO: 612826 DRWN: GSHARMA CHK'D: MSASAO APPR: MSASAO INITIAL REVISION: DRWN: TNISHIDA02 APPR: TKUSUHARA01 THIRD ANGLE PROJECTION DRAWING 2019/02/22 2019/02/27 2019/02/27 2017/03/28 2017/04/03 SERIES A3-SIZE 505070 3 0.35 BB CONN. H=0.6 SSB6 RP PLUG ASSY PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5050700000 MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 007 B SHEET NUMBER 2 OF 3 1 A 10 9 7 8 5 6 4 3 2 1 (2.16) F F (1.08) PULL OUT DIRECTION Y TOP TAPE (A) X 1.75 ±0.1 D (11.5) 24 ±0.3 (A) 0.3 ±0.05 (1.14) (0.64) (2.16) E X SECTION X-X Y (2) ⌀ 1.5 +0.1 0 E 8 ±0.1 4 ±0.1 ACCUMULATIVE PITCH 40±0.2 D SECTION Y-Y C C 24 B キャリアテープ幅 CARRIER TAPE WIDTH 12.63 11.93 10.88 10.18 29.4 25.4 9.83 9.48 8.78 8.43 7.38 C B (A) ----64 ----60 ○ --54 ○ --50 ○ --48 ----46 ○ --42 ○ --40 B ○ --34 HIGH VOL TOOL LOW VOL TOOL MATERIAL No. CIRCUIT SAMPLE PREPARATION 505070-6422 505070-6022 505070-5422 505070-5022 505070-4822 505070-4622 505070-4222 505070-4022 505070-3422 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 10 FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 9 2019/02/27 ± 1.0 ° 4 PLACES ± 0.01 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 05:28:35 8 ANGULAR TOL 7 6 5 4 CURRENT REV DESC: RELEASED EC NO: 612826 DRWN: GSHARMA CHK'D: MSASAO APPR: MSASAO INITIAL REVISION: DRWN: TNISHIDA02 APPR: TKUSUHARA01 THIRD ANGLE PROJECTION DRAWING 2019/02/22 2019/02/27 2019/02/27 2017/03/28 2017/04/03 SERIES A3-SIZE 505070 3 0.35 BB CONN. H=0.6 SSB6 RP PLUG ASSY PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5050700000 MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 007 B SHEET NUMBER 3 OF 3 1 A 7 8 A ±0.25 0.375 ±0.1 F 0.175 E CL 0.10 (TERMINAL WIDTH) �0.375� �B� CL D B A FITTING NAIL 14.76 TERMINAL ⌖ 0.15 X �0.375� �2� CL WAFER:LIQUID CRYSTAL POLYMER UL94V-0(COLOR :BLACK) TERMINAL:COPPER ALLOY FITTING NAIL : COPPER ALLOY 2 PLATING TERMINAL : CONTACT AREA: SEPARATED GOLD PLATING (0.1 MICROMETER MINIMUM). SOLDER TAIL AREA: SEPARATED GOLD PLATING. UNDERPLATE: NICKEL OVERALL. *DIVIDE INTO PARTS THE GOLD PLATING OF THE CONTACT AND THE TAIL PART BY THE NICKEL PLATING. FITTING NAIL : CONTACT AREA: SEPARATED GOLD PLATING (0.1 MICROMETER MINIMUM). SOLDER TAIL AREA: SEPARATED GOLD PLATING. UNDERPLATE: NICKEL OVERALL. *DIVIDE INTO PARTS THE GOLD PALATING OF THE CONTACT AND THE TAIL PART BY THE NICKEL PLATING. *EVEN THOUGH GOLD PLATING ON THE TOP SURFACE OF NAIL MIGHT BE THIN, NO FUNCTIONAL PROBLEM. 3 APPLY FOR (CIRCUIT/2)=EVEN. 4 MATE WITH :505066-**22 (H=0.6) , 505270**12 (H=0.7) 5 TAIL AND FITTING NAIL COPLANARITY TO BE 0.08MAXIMUM. 6 PROHIBITED AREA OF PATTERN WIRING AND SOLDER. (FOR EACH AREA, THE WIRING THAT TOUCHES ON THE SOLDER CAN BE ATTACHED, THEN COVERED WITH A FILM TO KEEP SOLDER OUT). 7 THIS DIMENSION SHOWS THE DIMENSION BETWEEN SOLDERING SURFACE OF SOLDER TAILS. DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 9 2020/09/28 14.16 11.90 13.56 13.71 13.01 12.66 11.96 11.26 10.91 10.56 9.86 9.51 9.16 8.46 7.76 6.71 6.36 6.01 5.66 5.31 4.96 4.61 4.26 3.91 3.56 13.11 12.41 12.06 11.36 10.66 10.31 9.96 9.26 8.91 8.56 7.86 7.16 6.11 5.76 5.41 5.06 4.71 4.36 4.01 3.66 3.31 2.96 10.85 10.15 9.80 9.10 8.40 8.05 7.70 7.00 6.65 6.30 5.60 4.90 3.85 3.50 3.15 2.80 2.45 2.10 1.75 1.40 1.05 0.70 D C B 12.51 11.81 11.46 10.76 10.06 9.71 9.36 8.66 8.31 7.96 7.26 6.56 5.51 5.16 4.81 4.46 4.11 3.76 3.41 3.06 2.71 2.36 7 6 5 505070-7022 505070-6422 505070-6022 505070-5822 505070-5422 505070-5022 505070-4822 505070-4622 505070-4222 505070-4022 505070-3822 505070-3422 505070-3022 505070-2422 505070-2222 505070-2022 505070-1822 505070-1622 505070-1422 505070-1222 505070-1022 505070-0822 505070-0622 --------- ----------------------------------------------- ○ ○ ○ --○ ○ --○ ○ ○ ○ ○ --- 70 64 60 58 54 50 48 46 42 40 38 34 30 24 22 20 18 16 14 12 10 8 6 E D ○ ○ C ○ ○ ○ ○ EMBOSSED TAPE HIGH VOL. LOW VOL. PACKAGE TOOL TOOL SAMPLE PREPARATION A CIRCUIT ○：TOOLED ORDER NO. △：WORK IN PROCESS B ---:TOOLING TO BE CONFIRMED CONNECTOR SERIES NO. : 505070-**19 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 20:1 CURRENT REV DESC: RELEASED GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 1.0 ° 4 PLACES ± 0.01 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:00:54 8 1 F 1 MATERIAL C 2 3 0.7 0.15 (FIITING NAIL WIDTH) 3 0.375 ±0.1 1.26 ±0.2 2 (PITCH) 4 X B ±0.25 0.35 5 6 0.48 9 (PICKING AREA) 10 4 EC NO: 646121 DRWN: YSEKI01 CHK'D: STERUKI APPR: YNAITO INITIAL REVISION: DRWN: TNISHIDA02 APPR: TKUSUHARA01 THIRD ANGLE PROJECTION 0.35 BB CONN. SSB6 RP PLUG ASSY 2019/09/19 2020/09/28 2020/09/28 DRAWING 2017/03/28 2017/04/03 SERIES A3-SIZE 505070 3 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5050701000 MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 019 C SHEET NUMBER 1 OF 2 1 A C MAX. 0.35 (PITCH) 0.535 ±0.03 (NAIL) 6 1.38 ±0.03 E (0.44) 1.46 MAX. 6 (NAIL) 1.33 ±0.03 (TERM) 1 ±0.03 E CL (0.48) CL F (0.16) 1.05 ±0.03 0.35 ±0.03 (PITCH) 1 0.375 ±0.03 (B) (0.21) 0.375 ±0.03 B ±0.03 2 (0.48) 0.375 ±0.03 3 0.375 ±0.03 6 0.485 ±0.03 (TERM) 6 D MIN. 2.07 MIN. F 4 (0.67) 6 5 6 (0.44) 7 8 6 9 0.33 MIN. 10 D 0.23 ±0.03 (NAIL) 0.18 ±0.03 (TERM) 0.25 MIN. 6 RECOMMENDED METAL MASK LAYOUT(REFERENCE) RECOMMENDED P.W.BOARD PATTERN LAYOUT(REFERENCE) PROHIBITED AREA OF PATTERN WIRING AND SOLDER. (FOR EACH AREA, THE WIRING THAT TOUCHES ON THE SOLDER CAN BE ATTACHED, THEN COVERED WITH A FILM TO KEEP SOLDER OUT.) 7 B RECOMMENDED THICKNESS OF METAL MASK : t=0.08mm RECOMMENDED OPEN APERTURE RATIO OF METAL MASK : 80% C 7 0.6 ±0.1 C 0.7 ±0.1 6 D B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 20:1 CURRENT REV DESC: RELEASED GENERAL TOLERANCES (UNLESS SPECIFIED) MATED CONDITION (505270/505070) MATED CONDITION (505066/505070) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 9 2020/09/28 ± 1.0 ° 4 PLACES ± 0.01 3 PLACES ± 0.03 2 PLACES ± 0.05 1 PLACE ± 0.1 0 PLACES ± 0.2 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:00:54 8 ANGULAR TOL 7 6 5 4 EC NO: 646121 DRWN: YSEKI01 CHK'D: STERUKI APPR: YNAITO INITIAL REVISION: DRWN: TNISHIDA02 APPR: TKUSUHARA01 THIRD ANGLE PROJECTION 0.35 BB CONN. SSB6 RP PLUG ASSY 2019/09/19 2020/09/28 2020/09/28 DRAWING 2017/03/28 2017/04/03 SERIES A3-SIZE 505070 3 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 5050701000 MATERIAL NUMBER CUSTOMER SEE CHART 2 GENERAL PSD 019 C SHEET NUMBER 2 OF 2 1 A