52207-1233

10 9 8 7 6 5 4 3 2 1 注記（NOTE)： 1．材質 MATERIAL 　ハウジング：ポリアミド（PA），ナチュラル（白色），ガラス充填，UL94V-0　 　 HOUSING:POLYAMIDE, NATURAL(WHITE), GLASS FILLED, UL94V-0 　アクチュエータ：ポリフェニレンサルファイド(PPS)，ナチュラル（茶色），ガラス充填，UL94-V0 　 ACTUATOR:POLYPHENYLENE SULFIDE, NATURAL(BROWN), GLASS FILLED, UL94V-0 　 ターミナル：リン青銅（t=0.32) 　 TERMINAL:PHOSPHOR BRONZE(t=0.32) 　 ネイル(補強金具）：リン青銅（t=0.25) 　 FITTING NAIL:PHOSPHOR BRONZE(t=0.25) 2．めっき仕様 PLATING 　ターミナル TERMINAL 錫銀ビスマスめっき（1.0μm以上） TIN SILVER BISMUTH PLATING (1.0 MICROMETER MINIMUM) 下地：ニッケルめっき（1.0μm以上） UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM) 　ネイル（補強金具） FITTING NAIL 錫めっき（1.0μm以上） TIN PLATING (1.0 MICROMETER MINIMUM) 下地：ニッケルめっき（1.0μm以上） UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM 3　．C0.3はFPC/FFCの導体部にかからないこと C0.3 MUST NOT BE OVERLAPED TO PATTERN OF FPC/FFC. 4．エンボステープ梱包時は、アクチュエータがロックした状態とする。 　 IN THE PACKAGE, ACTUATOR SHOULD BE LOCKED. 5 ． パターン剥離止め用金具 　 FITTTING NAIL FOR PREVENTION OF PEELING OF P.C.B. PATTERN. 6 ．ソルダーテール半田付け面、及び金具半田付け面の平坦度：0.15mm MAX. COPLANARITY OF SOLDER TAILS AND FITTING NAILS TO BE 0.15mm MAX. 7．ELV及びRoHS適合品 ELV AND RoHS COMPLIANT F E F E 38.7 34.7 33.7 32.7 31.7 30.7 29.7 28.7 27.7 26.7 25.7 24.7 23.7 22.7 21.7 20.7 19.7 18.7 17.7 16.7 15.7 14.7 13.7 12.7 11.7 10.7 9.7 8.7 7.7 D 5 C 6 B E AS LE CE E E-R EN PR FER NLY RE SE O U C 52207-3433 34 52207-3033 30 52207-2933 29 52207-2833 28 52207-2733 27 52207-2633 26 52207-2533 25 52207-2433 24 52207-2333 23 52207-2233 22 52207-2133 21 52207-2033 20 52207-1933 19 52207-1833 18 52207-1733 17 52207-1633 16 52207-1533 15 52207-1433 14 52207-1333 13 52207-1233 12 52207-1133 11 52207-1033 10 52207-0933 9 52207-0833 8 7 52207-0733 52207-0633 6 5 52207-0533 4 52207-0433 52207-0333 3 EMBOSSED PACKAGE ORDER NO. 極数 B A オーダー番号 CKT. CONNECTOR SERIES NO.: 52207-**22 35.2 31.2 30.2 29.2 28.2 27.2 26.2 25.2 24.2 23.2 22.2 21.2 20.2 19.2 18.2 17.2 16.2 15.2 14.2 13.2 12.2 11.2 10.2 9.2 8.2 7.2 6.2 5.2 4.2 33 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 D C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A DOCUMENT STATUS 10 FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 RV RELEASE DATE 9 8 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　±　3　° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 DIMENSION UNITS SCALE mm 8:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 CURRENT REV DESC: REVISED EC NO: 601573 DRWN: AISHII CHK'D: TRSUZUKI APPR: INITIAL REVISION: DRWN: NASANUMA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2018/07/17 2018/08/10 PRODUCT CUSTOMER DRAWING 2012/09/21 2013/03/15 DRAWING SERIES A3-SIZE 52207 3 1.0 MM FPC CONN. ZIF R/A HOUSING ASSY (UPPER CONTACT) DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-52207-069 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D SHEET NUMBER 1 OF 2 1 A 10 9 8 7 6 5 4 3 2 0.3 ±0.05 0.3 ±0.05 仕上がり厚さ THICKNESS F 1 仕上がり厚さ THICKNESS F めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) C FFC構成推奨仕様 RECOMMENDED STRUCTURE OF FPC RECOMMENDED STRUCTURE OF FFC RECOMMENDED P.C.BOARD PATTERN DIMENSION.(REF.) THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION (MOUNT SIDE) マスク厚 ：100μm マスク開口率 ：100% SCREEN THICKNESS :100 MICROMETER SCREEN OPEN RATIO :100% A 10 RV RELEASE DATE 9 8 B U (マウント面） DOCUMENT STATUS C FPC/FFCについて： 　 抜き方向は、導体側から補強板側を推奨致します。 　 尚、接着剤の接点部への付着は導通不良の原因になりますので、 　 染み出しが無い様お願い致します。 ABOUT FPC/FFC: RECOMMENDED PUNCHER DIRECTION: E ASFROM CONDUCTOR SIDE TO STIFFNER SIDE E EL CE PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND E-R RENPLEASE R LY E P BECAUSE THERE IS A POSSIBILITY THAT THE EXTRA ADHESIVE　 N F RE SE O CAUSES THE　DEFECT IN ELECTRICAL CONTINUITY. NO FOOT PRINT AREA 推奨基板レイアウト D FPC構成推奨仕様 パターン書き込み禁止エリア B E 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 補強板：ポリイミド REINFORCE BOARD: POLYMIDE 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド(25μm) BASE FILM: POLYIMIDE(25μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) 熱硬化接着剤 THERMOSETTING ADHESIVE D 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) APPLICABLE FPC/FFC RECOMMENDED DIMENSION 補強板：ポリエステル系 REINFORCE BOARD: PET 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 適合FPC/FFC推奨寸法 カバーレイ　:　ポリイミド(25μm) COVER FILM: POLYIMIDE(25μm) E FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) 3 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　±　3　° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 DIMENSION UNITS SCALE mm 5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 CURRENT REV DESC: REVISED EC NO: 601573 DRWN: AISHII CHK'D: TRSUZUKI APPR: INITIAL REVISION: DRWN: NASANUMA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2018/07/17 2018/08/10 PRODUCT CUSTOMER DRAWING 2012/09/21 2013/03/15 DRAWING SERIES A3-SIZE 52207 3 1.0 MM FPC CONN. ZIF R/A HOUSING ASSY (UPPER CONTACT) DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-52207-069 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET SEE TABLE 2 D SHEET NUMBER 2 OF 2 1 A