52745-1233

9 7 8 6 5 4 3 2 1 注記NOTES 　1.使用材料 MATERIAL ハウジング：ポリアミド(PA)、ガラス充填、UL94V-0、ナチュラル(白) HOUSING:POLYAMIDE,GLASS FILLED,UL94V-0,NATURAL（WHITE） アクチュエータ：ポリフェニレンサルファイド（PPS）、ガラス充填、UL94V-0、黒 ACTUATOR:POLYPHENYLENE SULFIDE,GLASS FILLED,UL94V-0,BLACK ターミナル：リン青銅、(t=0.2) TERMINAL:PHOSPHOR BRONZE 金具：リン青銅、（t=0.2） FITTING NAIL:PHOSPHOR BRONZE 2.めっき仕様 PLATING ターミナル TERMINAL 錫銀ビスマスめっき(1.0μｍ以上) 下地：ニッケルめっき(1.0μｍ以上) TIN SILVER BISMUTH PLATING (1.0 MICROMETER MINIMUM) UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM) 金具 FITTING NAIL 錫めっき(1.0μｍ以上) 下地：ニッケルめっき(1.0μｍ以上) TIN PLATING (1.0 MICROMETER MINIMUM) UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM) 　3.エンボステープ梱包時は、アクチュエータがロックした状態になります。 IN THE PACKAGE,ACTUATOR SHOULD BE LOCKED. 偶数極に適用 4 APPLY FOR EVEN CIRCUIT. 5 ﾊﾟﾀｰﾝ剥離止め金具 FITTING NAIL FOR PREVENTION OF PEELING OF P.W.B. PATTERN. R0.3は、FPCの導体部にかからないこと 6 R0.3 MUST NOT BE OVERLAPED TO PATTERN OF FPC. 7 ソルダーテール方向のズレ量、及び金具半田付け面のずれ量は、 H 基準面　　に対し上方向0.1 MAX、下方向0.15MAXとする。 MISALIGNMENT OF SOLDER TAILS AND FITTING NAILS FROM H UPPER DIRECTION 0.1 MAX., LOWER DIRECTION 0.15 MAX. 8.ELV及びRoHS適合品 ELV AND RoHS COMPLIANT. E D C B K 5 7 金具 FITTING NAIL 0.85 1.28 1.02 9 10.65 10.15 9.65 9.15 8.65 8.15 7.65 7.15 6.65 6.15 5.65 5.15 4.65 4.15 3.65 2.65 9.5 9 8.5 8 7.5 7 6.5 6 5.5 5 4.5 4 3.5 3 2.5 1.5 D C B (A) 52745-2033 52745-1933 52745-1833 52745-1733 52745-1633 52745-1533 52745-1433 52745-1333 52745-1233 52745-1133 52745-1033 52745-0933 52745-0833 52745-0733 52745-0633 52745-0433 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 4 C B 極数 EMBOSSED PACKAGE ORDER No. オーダー番号 CKT. CONNECTOR SERIES NO. : 52745-**22 0.74 0.66 2.455 DOCUMENT STATUS 14.3 13.8 13.3 12.8 12.3 11.8 11.3 10.8 10.3 9.8 9.3 8.8 8.3 7.8 7.3 6.3 D THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 16.1 15.6 15.1 14.6 14.1 13.6 13.1 12.6 12.1 11.6 11.1 10.6 10.1 9.6 9.1 8.1 E P1 RELEASE DATE VIEW K (金具部投影図) (DETAIL OF FITTING NAIL) 2018/04/13 8 03:51:02 7 6 5 GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　±　3　° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 DIMENSION UNITS SCALE mm 10:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS CURRENT REV DESC: REVISED EC NO: 600129 DRWN: YCHEN128 CHK'D: KTAKAHASHI APPR: NUKITA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 3 2018/04/09 2018/04/12 2018/04/13 2012/09/06 2013/03/15 PRODUCT CUSTOMER DRAWING SERIES A3-SIZE 52745 2 DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-52745-055 MATERIAL NUMBER DRAWING A 0.5MM FPC CONN ZIF R/A HOUSING ASSY (UPPER CONTACT) PSD 001 B SHEET NUMBER CUSTOMER GENERAL MARKET 1 1 OF 2 7 8 0.5(N+1)±0.07 0.35+0.04 -0.03 0.5±0.05 　　 　APPLICABLE FFC PLATING RECOMMENDED DIMENSION THICKNESS: 0.3+0.03/-0.03 THICKNESS: 0.3+0.03/-0.03 仕上がり厚さ：0.3±0.03 仕上がり厚さ：0.3±0.03 0.5(N-1)±0.05 L M SOLDERING AREA OF FITTING NAIL コネクタ位置 CONNECTOR POSITION DETAIL L 1.25 (0.2) 金具パターンエリア (0.3) (0.3) C 1.25 1.1 推奨基板レイアウト(マウント面) FPC構成推奨仕様 FFC構成推奨仕様 RECOMMENDED STRUCTURE OF FPC RECOMMENDED STRUCTURE OF FFC マスク厚　　:100μm マスク開口率：100% SCREEN THICKNESS : 100μm SCREEN OPEN TATIO : 100% PATTERN R0.303 BOARD VIEW M (DETAIL OF FITTING NAIL ON PATTERN) DOCUMENT STATUS 10 FORMAT: master-tb-prod-A3 REVISION: H DATE: 2018/01/18 P1 RELEASE DATE 9 2018/04/13 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION (0.605) (FROM PATTERN EDGE) A C FPC/FFCについて： 　 抜き方向は、導体側から補強板側を推奨致します。 　 尚、接着剤の接点部への付着は導通不良の原因になりますので、 　 染み出しが無い様お願い致します。 ABOUT FPC/FFC: RECOMMENDED PUNCHER DIRECTION: FROM CONDUCTOR SIDE TO STIFFNER SIDE PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND BECAUSE THERE IS A POSSIBILITY THAT THE EXTRA ADHESIVE　 CAUSES THE　DEFECT IN ELECTRICAL CONTINUITY. RECOMMENDED P.C.BOARD PATTERN DIMENSION (MOUNTING SIDE) B カバーレイ　:　ポリイミド(25μm) COVER FILM: POLYIMIDE(25μm) 0.8 (0.3) 補強板：ポリイミド REINFORCE BOARD: POLYMIDE 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド(25μm) BASE FILM: POLYIMIDE(25μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 0.5±0.05 (PITCH) (NON-ACCUMULATIVE) 2.2 KEEPING OUT AREA OF PATTERN AND SOLDERING (0.3) 0.6MAX. パターンおよび 半田禁止エリア 1.94MIN. 0.45MAX. D 3.65 3.05 3.65 めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) 　　　 APPLICABLE FPC PLATING RECOMMENDED DIMENSION E 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 4±0.5 適合FFC推奨寸法 適合FPC推奨寸法 D F 6 6±0.5 4±0.5 E 仕上がり厚さ THICKNESS 0.3±0.03 (PITCH) 補強板 (STIFFENER BOARD) R0.3 仕上がり厚さ THICKNESS 0.5±0.08 1 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) (PITCH) 2 0.3 ±0.03 6±0.5 0.5±0.05 0.5(N-1)±0.05 0.5±0.08 3 0.3 ±0.03 0.5(N+1)±0.07 0.5±0.1 4 補強板 (STIFFENER BOARD) 0.5(N-1)±0.05 0.5±0.1 F 5 6 補強板：ポリエステル系 REINFORCE BOARD: PET 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 9 めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) 10 03:51:02 8 7 6 GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　±　3　° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 DIMENSION UNITS SCALE mm 5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 CURRENT REV DESC: REVISED EC NO: 600129 DRWN: YCHEN128 CHK'D: KTAKAHASHI APPR: NUKITA INITIAL REVISION: DRWN: TMORISHITA APPR: KMORIKAWA THIRD ANGLE PROJECTION 2018/04/09 2018/04/12 2018/04/13 2012/09/06 2013/03/15 DRAWING SERIES A3-SIZE 52745 3 0.5MM FPC CONN ZIF R/A HOUSING ASSY (UPPER CONTACT) PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER SD-52745-055 MATERIAL NUMBER PSD 001 CUSTOMER GENERAL MARKET 2 B SHEET NUMBER 2 OF 2 1 A