52746-0433

10 9 7 8 5 6 4 3 2 1 注記(NOTES) 1. 材質　MATERIAL ハウジング：ポリアミド（PA）、ガラス充填、白色、UL94V-0 HOUSING : POLYAMIDE , GLASS FILLED, WHITE, UL94V-0 アクチュエータ:ポリフェニレンサルファド(PPS), ガラス充填、茶色、UL94V-0 ACTUATOR : POLYPHENYLENE SULFIDE , GLASS FILLED, BROWN, UL94V-0 ターミナル：リン青銅（t = 0.2） TERMINAL : PHOSPHOR BRONZE ( t = 0.2) 金具：リン青銅（t = 0.2） NAIL : PHOSPHOR BRONZE ( t = 0.2) 2. メッキ仕様　PLATING ターミナル TERMINAL 錫銀ビスマスメッキ(1.0μm以上） TIN SILVER BISMUTH PLATING（1.0MICROMETER MINIMUM) 下地メッキ：ニッケルメッキ(1.0μm以上） UNDER PLATING : NICKEL PLATING（1.0MICROMETER MINIMUM) 金具 NAIL 錫メッキ(1.0μm以上） TIN PLATING（1.0MICROMETER MINIMUM) 下地メッキ：ニッケルメッキ(1.0μm以上） UNDER PLATING : NICKEL PLATING（1.0MICROMETER MINIMUM) 3 R0.3はFPCの導体部にかからないこと R0.3 MUST NOT BE OVERLAPED TO PATTERN OF FPC. 4 偶数極に適用 APPLY FOR EVEN CIRCUIT. 5 パターン剥離止め金具 FITTING NAIL FOR PREVENTION OF PEELING OF P.W.B. PATTERN. 6 ソルダーテール半田付け面のズレ量、及び金具半田付け面のズレ量は、 基準面Hに対して上方向に0.1MAXIMUM、下方向0.15MAXIMUMとする。 MISALIGNMENT OF SOLDER TAILS AND FITTING NAILS FROM DATUM-H UPPER DIRECTION:0.1MAXIMUM LOWER DIRECTION:0.15MAXIMUM 7. エンボステープ梱包時は、アクチュエータがロックした状態になります。 IN THE PACKAGE,ACTUATOR OF PART NO.52746-**22 SHOULD BE LOCKED. 8. ELV及びRoHS適合品 ELV AND RoHS COMPLIANT F 0.5 0.25 E D C K 5 6 金具 FITTING NAIL B 1.28 0.85 F E D 16.1 15.1 14.6 14.1 13.6 13.1 12.1 11.6 11.1 10.6 10.1 9.6 9.1 8.1 14.3 13.3 12.8 12.3 11.8 11.3 10.3 9.8 9.3 8.8 8.3 7.8 7.3 6.3 10.65 9.65 9.15 8.65 8.15 7.65 6.65 6.15 5.65 5.15 4.65 4.15 3.65 2.65 9.5 8.5 8 7.5 7 6.5 5.5 5 4.5 4 3.5 3 2.5 1.5 52746-2033 52746-1833 52746-1733 52746-1633 52746-1533 52746-1433 52746-1233 52746-1133 52746-1033 52746-0933 52746-0833 52746-0733 52746-0633 52746-0433 20 18 17 16 15 14 12 11 10 9 8 7 6 4 D C B (A) EMBOSSED PACKAGE ORDER No. オーダー番号 極数 CKT. C B CONNECTOR SERIES NO. : 52746-**22 0.66 A GENERAL TOLERANCES (UNLESS SPECIFIED) 10 UNDER ±　0.2 10 OVER 30 UNDER ±　0.25 ±　0.3 30 OVER ANGULAR 　　± 3 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 0.74 1.02 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION VIEW K 2.455 (金具部投影図) (DETAIL OF FITTING NAIL) DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/11/03 08:33:26 8 7 6 5 DIMENSION UNITS SCALE mm 10:1 CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 0.5MM FPC CONN ZIF R/A HOUSING ASSY (BOTTOM CONTACT) EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: KNAGUMO APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/08/31 2013/04/16 DRAWING SERIES A3-SIZE 52746 3 SD-52746-031 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 GENERAL MARKET B1 SHEET NUMBER 1 OF 2 1 A 7 8 6 5 0.5(N+1)±0.07 3 0.5(N+1)±0.07 0.5±0.1 0.35+0.04 -0.03 0.3±0.03 (PITCH) めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) 　　APPLICABLE FFC OF TIN-LEAD PLATING RECOMMENDED DIMENSION 仕上がり厚さ：0.3±0.03 仕上がり厚さ：0.3±0.03 THICKNESS: 0.3+0.03/-0.03 THICKNESS: 0.3+0.03/-0.03 0.5(N-1)±0.05 D (0.2) 1.25 コネクタ位置 1.25 CONNECTOR POSITION マスク厚　　： 100μm マスク開口率： 100% FPC構成推奨仕様 FFC構成推奨仕様 RECOMMENDED STRUCTURE OF FPC RECOMMENDED STRUCTURE OF FFC FPC/FFCについて： 　 抜き方向は、導体側から補強板側を推奨致します。 　 尚、接着剤の接点部への付着は導通不良の原因になりますので、 　 染み出しが無い様お願い致します。 ABOUT FPC/FFC: RECOMMENDED PUNCHER DIRECTION: FROM CONDUCTOR SIDE TO STIFFNER SIDE PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND BECAUSE THERE IS A POSSIBILITY THAT THE EXTRA ADHESIVE　 CAUSES THE　DEFECT IN ELECTRICAL CONTINUITY. SCREEN THICKNESS : 100μm SCREEN OPEN RATIO : 100% RECOMMENDED P.C.BOARD PATTERN DIMENSION(REF.) (MOUNTING SIDE) 0.6MAX. パターンおよび 半田禁止エリア PATTERN 1.94MIN. 0.45MAX. KEEPING OUT AREA OF PATTERN AND SOLDERING R0.303 BOARD GENERAL TOLERANCES (UNLESS SPECIFIED) ±　--10 UNDER 10 OVER 30 UNDER ±　--±　--30 OVER ANGULAR 　　± --- ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS (0.605) 金具パターンエリア SOLDERING AREA OF FITTING NAIL (0.3) (0.3) VIEW M (DETAIL OF FITTING NAIL ON PATTERN) M DETAIL L DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/11/03 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION (FROM PATTERN EDGE) A C 1.1 推奨基板レイアウト (マウント面) B カバーレイ　:　ポリイミド(25μm) COVER FILM: POLYIMIDE(25μm) (0.3) 3.05 0.8 0.5±0.05 (PITCH) (NON-ACCUMULATIVE) L C 補強板：ポリイミド REINFORCE BOARD: POLYMIDE 熱硬化接着剤 THERMOSETTING ADHESIVE ベースフィルム：ポリイミド(25μm) BASE FILM: POLYIMIDE(25μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) 熱硬化接着剤 THERMOSETTING ADHESIVE 3.65 2.2 (0.3) 3.65 E 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 　　APPLICABLE FPC OF TIN-LEAD PLATING RECOMMENDED DIMENSION 6±0.5 適合半田めっきFFC推奨寸法 適合半田めっきFPC推奨寸法 めっき：錫めっき(0.5-1.2μm)　 　下地ニッケル(1-5μm) PLATING: TIN(0.5-1.2μm)　 　　　 NICKEL UNDER(1-5μm) 3 補強板 (STIFFENER BOARD) 6±0.5 E F 0.5±0.05 補強板 (STIFFENER BOARD) 4±0.5 R0.3 仕上がり厚さ THICKNESS 0.5±0.08 4±0.5 (PITCH) 1 0.3 ±0.03 仕上がり厚さ THICKNESS 0.5(N-1)±0.05 0.5±0.08 0.5±0.05 D 2 0.3 ±0.03 0.5(N-1)±0.05 0.5±0.1 F 4 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 導体部：　銅箔(35 or 50μm) COPPER FOIL (35 or 50μm) 9 補強板：ポリエステル系 REINFORCE BOARD: PET 接着剤(難燃ポリエステル系) ADHESIVE（FLAME-RETARDANT POLYESTER ADHESIVE) 絶縁テープ：ポリエステル系(25μm) INSULATING FILM: PET(25μm) 10 08:33:26 8 7 6 5 DIMENSION UNITS SCALE mm 5:1 CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 3.0 ° 4 PLACES ± 0.2 3 PLACES ± 0.25 2 PLACES ± 0.3 1 PLACE ± 0 PLACES ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 0.5MM FPC CONN ZIF R/A HOUSING ASSY (BOTTOM CONTACT) EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: KNAGUMO APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/08/31 2013/04/16 DRAWING SERIES A3-SIZE 52746 3 SD-52746-031 MATERIAL NUMBER PSD 001 CUSTOMER SEE CHART 2 GENERAL MARKET B1 SHEET NUMBER 2 OF 2 1 A 10 9 8 7 6 5 4 3 2 1 F F 1. 製品番号52746-**22の梱包状態はアクチュエータがロックした状態とする。 詳細寸法については図面SD-52746-031を参照下さい。 IN THE PACKAGE, ACTUATOR OF PART NO.52746-**22 SHOULD BE LOCKED DETAIL DIMENSIONS, SEE SD-52746-031 　 　　　 　　 E E D D 4. トップテープの剥離強度については、IEC60286-3に準拠 　 TOP TAPE PEEL FORCE IS DEFINED BY IEC60286-3. C C 6. ELV及びRoHS適合品 ELV AND RoHS COMPLIANT B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/11/03 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:33:27 8 ANGULAR TOL 7 6 5 4 EMBOSS TAPE PACKAGED FOR 0.5MM FPC CONN ZIF R/A HOUSING ASSY EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: KNAGUMO APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/05 2013/04/16 DRAWING SERIES A3-SIZE 52746 3 SD-52746-032 MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 001 A SHEET NUMBER 1 OF 3 1 A 10 9 8 7 5 6 4 3 2 1 F F 22 E E D D 52746-2033 -1833 -1733 -1633 -1533 -1433 -1233 -1133 -1033 -0933 -0833 -0733 52746-0633 C B C B MATERIAL NO. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/11/03 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:33:27 8 ANGULAR TOL 7 6 5 4 EMBOSS TAPE PACKAGED FOR 0.5MM FPC CONN ZIF R/A HOUSING ASSY EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: KNAGUMO APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/05 2013/04/16 DRAWING SERIES A3-SIZE 52746 3 SD-52746-032 MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 001 A SHEET NUMBER 2 OF 3 1 A 10 9 8 7 6 5 4 3 2 1 F F E E 22 D D C C B B 52746-0433 MATERIAL NO. THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm NTS CURRENT REV DESC: REMOVED OBSOLETED PART NUMBER AS PER PCN#512672. GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS FORMAT: master-tb-prod-A3 REVISION: J1 DATE: 2021/05/01 P1 RELEASE DATE 9 2022/11/03 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 08:33:27 8 ANGULAR TOL 7 6 5 4 EMBOSS TAPE PACKAGED FOR 0.5MM FPC CONN ZIF R/A HOUSING ASSY EC NO: 724799 DRWN: SUGEEB CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: KNAGUMO APPR: KMORIKAWA THIRD ANGLE PROJECTION 2022/10/21 2022/11/03 2022/11/03 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2012/09/05 2013/04/16 DRAWING SERIES A3-SIZE 52746 3 SD-52746-032 MATERIAL NUMBER CUSTOMER GENERAL SEE TABLE 2 PSD 001 A SHEET NUMBER 3 OF 3 1 A