54104-3696

LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH SCOPE 9(& 2$ 0.5 mm FPC This specification covers the 0.5mm PITCH FPC CONNECTOR series. PRODUCT NAME AND PART NUMBER Material Number Product Name 4X ( X;O Housing Assembly(Straight Type) LEAD FREE + 9X Embossed Tape Package For 54104-**39 LEAD FREE Refer to drawing. RATINGS Standard Item 50V Rated Voltage(MAXIMUM) [AC( rms)/DC] 0.5A Rated Current (MAXIMUM) -20 Ambient Temperature Range +85 *1 1 Including terminal temperature rise. REV. SHEET A B 1-10 1-10 REVISE ON PC ONLY B REVISED J2004-2241 ’04/02/04 Y.SAKIYAMA REV. DESCRIPTION DESIGN CONTROL STATUS TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION WRITTEN BY: J Y.SAKIYAMA DOCUMENT NUMBER PS-54104-069 CHECKED BY: M.SASAO APPROVED BY: M.SASAO DATE: YR/MO/DAY 2004/01/22 FILE NAME PS54104069.doc SHEET 1 OF 10 EN-37(019) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH PERFORMANCE Item Test Condition Requirement FPC 4-1-1 Contact Resistance 20mV 10mA (JIS C5402 5.4) Mate applicable FPC, measure by dry circuit , 20mV MAXIMUM, 10mA MAXIMUM. (JIS C5402 5.4) FPC DC 500V $ D/P $ D/P   4-1-2 Insulation Resistance (JIS C5402 5.2/MIL-STD-202 302) Mate applicable FPC together and apply 500V DC between adjacent terminal and ground. (JIS C5402 5.2/MIL-STD-202 Method 302) FPC AC 250V 1 (JIS C5402 5.1/MIL-STD-202 301) Mate applicable FPC, apply 250V AC for 1 minute between adjacent terminal or ground. (JIS C5402 5.1/MIL-STD-202 Method 301) Dielectric Strength . &J $ 4-2-2 No Breakdown Mechanical Performance Item 4-2-1 50 Megaohm MINIMUM $ D/P $ D/P   4-1-3 20 milliohm MAXIMUM Actuator Insertion/ Withdrawal Force FPC FPC Retention Force Test Condition &J $ FPC 25 3mm Mate applicable FPC and insert and withdraw actuator at the speed rate of 25 3mm/min. &J $ FPC 25 3 mm Insert the actuator, pull the FPC at the speed rate of 25+3/-3mm per minute. REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 Requirement 6 Refer to paragraph 6 7 Refer to paragraph 7 TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 2 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH Environmental Performance and Others Item &J $ 4-3-1 Repeated Actuator Insertion / Withdrawal Test Condition Requirement 1 10 20 Insert and withdraw actuator up to 20 cycles, at the speed rate of less than 10 cycle per minute. Contact Resistance 40 milliohm MAXIMUM FPC 2$ 4-3-2 Temperature Rise (UL 498) Mate applicable FPC and measure the temperature rise of contact when the maximum AC rated current is passed. (UL 498) Temperature Rise DC 1mA Appearance 30 °C MAXIMUM No Damage 3 10~55~10 Hz/ 1.5mm (MIL-STD-202 4-3-3 Vibration 2 201) Contact Resistance Amplitude: 1.5mm P-P Sweep time: 10~55~10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes (MIL-STD-202 Method 201) Discontinuity Appearance DC 1mA 40 milliohm MAXIMUM 1.0 microsecond MAXIMUM No Damage 2 6 490m/s {50G} 3 (JIS C0041/MIL-STD-202 213) 4-3-4 Shock 2 490m/s {50G}, 3 strokes in each X.Y.Z. axes. (JIS C0041/MIL-STD-202 Method 213 Contact Resistance Discontinuity REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 40 milliohm MAXIMUM 1.0 microsecond MAXIMUM TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 3 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION Item 4-3-5 Test Condition FPC 85 2 96 Heat Resistance 4-3-7 Cold Resistance Humidity Requirement 1 2 ( JIS C0021/MIL-STD-202 108 ) Mate applicable FPC and expose to 85+2/-2 degree C for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. ( JIS C0021/MIL-STD-202 Method 108 ) FPC 96 4-3-6 JAPANESE ENGLISH , Appearance Contact Resistance 1 2 Appearance Contact Resistance Appearance Contact Resistance SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 No Damage 40 milliohm MAXIMUM No Damage 40 milliohm MAXIMUM 4-1-3 Dielectric Strength Insulation Resistance B 40 milliohm MAXIMUM 40 2 ( JIS C0020 ) Mate applicable FPC and expose to –40+2/-2 degree C for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. ( JIS C0020 ) FPC 60 2 90 95% 96 1 2 (JIS C0022/MIL-STD-202 103) Mate applicable FPC and expose to 60+2/-2 degree C, relative humidity 90 to 95% for 96 hours. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. (JIS C0022/MIL-STD-202 Method 103) REVISE ON PC ONLY No Damage Must meet 4-1-3 20 megaohm MINIMUM TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 4 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION Item +85 10 FPC 30  P 4-3-8 4-3-9 4-3-10  P Temperature Cycling Salt Spray  SO2 Gas Test Condition -55 1  P JAPANESE ENGLISH Requirement 30 5 1 2 Mate applicable FPC connectors and subject to the following conditions for 10 cycles. Upon completion of the exposure period, the test specimens shall be conditioned at ambient room conditions for 1 to 2 hours, after which the specified measurements shall be performed. 10 cycle of a) –55 degree C 30 minutes b) +85 degree C 30 minutes (Transit time shall be with in 5 minutes) FPC 35 2 5 1% 48 4 Appearance ( JIS C0023/MIL-STD-202 101 ) Mate applicable FPC and expose to the following salt mist conditions. Upon completion of the exposure period, salt deposits shall be removed by a gentle wash or dip in running water, after which the specified measurements shall be performed. NaCl solution Concentration : 5+1/-1 % Spray time : 48 4 hours Ambient temperature : 35+2/-2 degree C ( JIS C0023/MIL-STD-202 Method 101 ) FPC 40 2 50 5ppm 24 Mate applicable FPC exposed to 50+5/-5ppm SO2 gas at 40+2/-2 degree C for 24 hours. Appearance Contact Resistance B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 40 milliohm MAXIMUM No Damage Contact Resistance 40 milliohm MAXIMUM  Appearance Contact Resistance REVISE ON PC ONLY No Damage No Damage 40 milliohm MAXIMUM. TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 5 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION Item 4-3-11 Test Condition XG0 NH3Gas Solderability Requirement FPC 28% 40 Mate applicable FPC exposed to NH3 gas evaporating from 28 % for 40 minutes. XG0 0.2mm 245±5°C 4-3-12 JAPANESE ENGLISH Contact Resistance 40 milliohm MAXIMUM 0.2mm 3±0.5 90% 90% of 3±0.5second Soldering Time: Solder Temperature: 245±5°C 0.2mm from terminal tip 0.2mm from fitting nail tip 8 Solder Wetting O:R immersed area must show no voids, pin holes (When reflowing) Repeat paragraph 8, condition twe times.. 4-3-13 Resistance to Soldering Heat 0.2mm 370 400 + $ 0.2mm Appearance 3 1 Solder Time: 3 1second Solder Temperature: 370 400 0.2mm from terminal tip 0.2mm from fitting nail tip No Damage ( { ) } Reference Standard Reference Unit PRODUCT SHAPE, DIMENSIONS AND MATERIALS Refer to the drawing. REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 6 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION &J $ No. of CIRCUIT 30 32 33 34 35 36 38 40 43 45 46 50 JAPANESE ENGLISH ACTUATOR INSERTION/WITHDRAWAL FORCE UNIT N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} INSERTION FORCE (MAXIMUM) 6 20 1st 6th 20th 53.9 51.9 51.9 {5.5} {5.3} {5.3} 55.8 53.9 53.9 {5.7} {5.5} {5.5} 56.8 54.8 54.8 {5.8} {5.6} {5.6} 57.8 55.8 55.8 {5.9} {5.7} {5.7} 58.8 56.8 56.8 {6.0} {5.8} {5.8} 59.7 57.8 57.8 {6.1} {5.9} {5.9} 61.7 59.7 59.7 {6.3} {6.1} {6.1} 63.7 61.7 61.7 {6.5} {6.3} {6.3} 66.6 64.6 64.6 {6.8} {6.6} {6.6} 68.6 66.6 66.6 {7.0} {6.8} {6.8} 69.6 67.6 67.6 {7.1} {6.9} {6.9} 73.5 71.5 71.5 {7.5} {7.3} {7.3} REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 WITHDRAWAL FORCE (MAXIMUM) 6 20 1st 6th 20th 62.7 58.8 58.8 {6.4} {6.0} {6.0} 64.6 60.7 60.7 {6.6} {6.2} {6.2} 65.6 61.7 61.7 {6.7} {6.3} {6.3} 66.6 62.7 62.7 {6.8} {6.4} {6.4} 67.6 63.7 63.7 {6.9} {6.5} {6.5} 68.6 64.6 64.6 {7.0} {6.6} {6.6} 70.5 66.6 66.6 {7.2} {6.8} {6.8} 72.5 68.6 68.6 {7.4} {7.0} {7.0} 75.4 71.5 71.5 {7.7} {7.3} {7.3} 77.4 73.5 73.5 {7.9} {7.5} {7.5} 78.4 74.5 74.5 {8.0} {7.6} {7.6} 82.3 78.4 78.4 {8.4} {8.0} {8.0} TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 7 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION FPC JAPANESE ENGLISH FPC RETENTION FORCE No. of CIRCUIT UNIT N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} 30 32 33 34 35 36 RETENTION FORCE (MINIMUM) 10 1st 10th 5.4 4.9 {0.55} {0.50} 6.4 5.8 {0.65} {0.60} 6.9 6.4 {0.70} {0.65} 7.4 6.9 {0.75} {0.70} 7.9 7.4 {0.80} {0.75} 8.4 7.9 {0.85} {0.80} REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 No. of CIRCUIT 38 40 43 45 46 50 UNIT N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} N {kgf} RETENTION FORCE (MINIMUM) 10 1st 10th 9.4 8.9 {0.95} {0.90} 10.3 9.8 {1.05} {1.00} 11.8 11.3 {1.20} {1.15} 12.7 12.2 {1.30} {1.25} 13.2 12.7 {1.35} {1.30} 15.2 14.7 {1.55} {1.50} TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 8 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION O:R JAPANESE ENGLISH INFRARED REFLOW CONDITION 9  245 5 245 5 MAX.(PEAK TEMP.) ) 40 60 (220 40 60 sec.(220 MIN.) O:R (Reflow) 90 120 90 120sec 150 180 (Pre-heat 150 180 MAX.) N: 6$ X TEMPERATURE CONDITION GRAPH (TEMPERATURE ON BOARD PATTERN SIDE) O:R O:R O:R NOTE; Please check the reflow soldering condition by your own devices beforehand. Because the condition changes by the soldering devices,p.c.boards,and so on. REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 9 OF 10 EN-37-1(019) LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH REV. REV. RECORD DATE ECN NO. WRITTEN BY : CHECKED BY : A RELEASED ‘04/01/22 J2004-2032 Y.SAKIYAMA M.SASAO B REVISED ‘04/02/04 J2004-2241 Y.SAKIYAMA M.SASAO REVISE ON PC ONLY B SEE SHEET 1 OF 10 REV. DESCRIPTION DOCUMENT NUMBER PS-54104-069 TITLE: 0.5 mm PITCH FPC CONN. ZIF SMT (UPPER CONTACT) -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME PS54104069.doc SHEET 10 OF 10 EN-37-1(019)