54132-3462

LANGUAGE PRODUCT SPECIFICATION 1. JAPANESE ENGLISH SCOPE 9(& 2$ 0.5mm FPC This specification covers the 0.5mm PITCH FPC CONNECTOR series. 2. PRODUCT NAME AND PART NUMBER Product Name Parts Number 4X ( X;O Housing Assembly (R/A Type, Bottom Contact) 54132-**68 LEAD FREE + 9X 54132-**68 Embossed Tape Package for 54132-**68 54132-**62 LEAD FREE ** 3. Refer to the drawing. RATINGS Item Standard 50 V Rated Voltage (MAXIMUM) [AC( 0.5 A Rated Current (MAXIMUM) -20 Ambient Temperature Range. *1 *1 +85°C*1 Including terminal temperature rise. REV. SHEET D rms) / DC] A B C D 1 81 81 8 1 9 REVISE ON PC ONLY REVISED ECN No. J2006-0776 ‘05/09/02 N.AIDA REV. DESCRIPTION DESIGN CONTROL STATUS J DOCUMENT NUMBER PS-54132-061 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION WRITTEN BY: M.UMEDA CHECKED BY: K.TOYODA APPROVED BY: N.UKITA DATE: YR/MO/DAY 2004/09/28 FILE NAME SHEET PS54132061.doc 1 OF 9 EN-37(019) LANGUAGE PRODUCT SPECIFICATION 4. 4 - 1. PERFORMANCE Electrical Performance Item Condition FPC 4-1-1 Contact Resistance Mate applicable FPC, measure by dry circuit, 20mV MAXIMUM, 10mA. (JIS C5402 5.4) DC 500V (JIS C5402 5.2/MIL-STD-202 FPC AC(rms) 250V (JIS C5402 5.1/MIL-STD-202 302) $ D/P 1 301) 50 Megohm MINIMUM $ D/P No Breakdown Mechanical Performance Item Condition &J $ 4-2-2 20 milliohm MAXIMUM $ D/P Dielectric Strength Mate applicable FPC, apply 250V AC (rms) for 1 minute between adjacent terminal or ground. (JIS C5402 5.1/MIL-STD-202 Method 301) 4 - 2. 4-2-1 $ D/P Mate applicable FPC, apply 500V DC between adjacent terminal or ground. (JIS C5402 5.2/MIL-STD-202 Method 302)   4-1-3 10mA (JIS C5402 5.4) FPC Insulation Resistance Standard 20mV   4-1-2 JAPANESE ENGLISH Standard &J $ FPC 25 3mm Actuator and Mate applicable FPC and Insert and withdraw actuator at Withdrawal Force the speed rate of 25 3mm/minute. FPC FPC Retention Force &J $ 25 Refer to paragraph 6 3mm FPC Insert the actuator, pull the FPC at the speed rate of 25 3mm/minute. REVISE ON PC ONLY D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 Refer to paragraph 7 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 2 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION 4 - 3. Environmental Performance and Others Item Condition &J $ 4-3-1 JAPANESE ENGLISH 1 Standard 10 20 Repeated Actuator Insert and withdraw actuator up to 20 cycles at Insertion / the speed rate of less than 10 cycles per minute. Withdrawal 2$ Temperature Rise (UL 498) Temperature 30 °C MAXIMUM Rise Carrying rated current load. (UL 498) 4-3-3 DC 1mA 3 1.5mm (MIL-STD-202 Vibration 4-3-4 Shock Appearance 10 55 10Hz/ 201) Contact Resistance 490m/s2{50G} (JIS C60068-2-27/MIL-STD-202 FPC Heat Resistance D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 1 microsecond MAXIMUM Appearance No damage 40 milliohm MAXIMUM Discontinuity 1 microsecond MAXIMUM Appearance No damage 96 108) 85 2 , 96 hours (JIS C60068-2-2/MIL-STD-202 Method 108) REVISE ON PC ONLY Discontinuity Contact Resistance 213) 85 2 1 2 (JIS C60068-2-2/MIL-STD-202 40 milliohm MAXIMUM 3 490m/s2{50G}, 3 strokes in each X,Y,Z axes. (JIS C60068-2-27/MIL-STD-202 Method 213) 4-3-5 No damage 2 1.5mm P-P Amplitude Sweep time 10 55 10Hz in 1 minute Duration 2 hours in each X, Y, Z axes (MIL-STD-202 Method 201) DC 1mA 6 40 milliohm MAXIMUM  FPC 4-3-2 Contact Resistance Contact Resistance 40 milliohm MAXIMUM TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 3 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION Item Condition FPC 4-3-6 JAPANESE ENGLISH Cold Resistance Standard -40 2 1 2 96 Appearance (JIS C60068-2-1) -40 2 , 96 hours (JIS C60068-2-1) 4-3-7 FPC  P Temperature Cycling 90 1 103) -55 30 5  P 1 5 a) –55 b) +85 FPC Insulation Resistance Contact Resistance Must meet 4-1-3 20 Megohm MINIMUM No damage 4 Appearance (JIS C60068-2-11/MIL-STD-202 FPC   40 2 D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 No damage 101) 50 Contact Resistance 40 milliohm MAXIMUM 5ppm 24 24 hours exposure to 50 5ppm. SO2 gas at 40 2 . REVISE ON PC ONLY 40 milliohm MAXIMUM 5 1% 48 4 hours exposure to a salt spray from the 5 1% solution at 35 2 . (JIS C60068-2-11/MIL-STD-202 Method 101) SO2 Gas 40 milliohm MAXIMUM 4-1-3 Dielectric Strength Appearance 30 minutes 30 minutes 35 2 48 4-3-10 No damage +85  P (JIS C0025) Salt Spray 40 milliohm MAXIMUM 1 2 (JIS C0025) 5 cycles of 4-3-9 Appearance Contact Resistance 60 2 Temperature Relative Humidity 90 95% Duration 96 hours (JIS C60068-2-3/MIL-STD-202 Method 103) 30 4-3-8 Contact Resistance FPC 60 2 95% 96 2 (JIS C60068-2-3/MIL-STD-202 Humidity No damage Contact Resistance 40 milliohm MAXIMUM TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 4 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION Item Condition FPC 4-3-11 XG0 28% 40 25mL 1L NH3 Gas JAPANESE ENGLISH XG0 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. 0.2mm 245 3 4-3-12 Solderability O:R Contact Resistance 40 milliohm MAXIMUM 0.2mm 3 0.5 Dip soldertails and fitting nails into the molten solder{held at 245 3 } up to 0.2mm from the bottom of the housing for 3 0.5 seconds. ( Standard Solder Wetting 95% 95% of immersed area must show no voids, pin holes ) 8 2 (When reflowing) Repeat paragraph 8, condition two times. 4-3-13 Resistance to Soldering Heat $ ) ( 0.2mm 370 400 + 0.2mm 5 Appearance No Damage Solder Time: 5 seconds MAX. Solder Temperature: 370 400 0.2mm from terminal tip and fitting nail tip ( ) { } 5. Reference Standard Reference Unit PRODUCT SHAPE, DIMENSIONS AND MATERIALS Refer to the drawing. REVISE ON PC ONLY D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 5 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION 6. &J $ No. of CIRCUIT JAPANESE ENGLISH ACTUATOR INSERTION/WITHDRAWAL FORCE INSERTION FORCE (MAXIMUM) UNIT 6 WITHDRAWAL FORCE (MAXIMUM) 1st 6th 20 20th 1st 6 6th 20 20th 30 N {kgf} 53.9 {5.5} 51.9 {5.3} 51.9 {5.3} 62.7 {6.4} 58.8 {6.0} 58.8 {6.0} 32 N {kgf} 55.8 {5.7} 53.9 {5.5} 53.9 {5.5} 64.6 {6.6} 60.7 {6.2} 60.7 {6.2} 33 N {kgf} 56.8 {5.8} 54.8 {5.6} 54.8 {5.6} 65.6 {6.7} 61.7 {6.3} 61.7 {6.3} 34 N {kgf} 57.8 {5.9} 55.8 {5.7} 55.8 {5.7} 66.6 {6.8} 62.7 {6.4} 62.7 {6.4} 35 N {kgf} 58.8 {6.0} 56.8 {5.8} 56.8 {5.8} 67.6 {6.9} 63.7 {6.5} 63.7 {6.5} 36 N {kgf} 59.7 {6.1} 57.8 {5.9} 57.8 {5.9} 68.6 {7.0} 64.6 {6.6} 64.6 {6.6} 38 N {kgf} 61.7 {6.3} 59.7 {6.1} 59.7 {6.1} 70.5 {7.2} 66.6 {6.8} 66.6 {6.8} 40 N {kgf} 63.7 {6.5} 61.7 {6.3} 61.7 {6.3} 72.5 {7.4} 68.6 {7.0} 68.6 {7.0} 43 N {kgf} 66.6 {6.8} 64.6 {6.6} 64.6 {6.6} 75.4 {7.7} 71.5 {7.3} 71.5 {7.3} 45 N {kgf} 68.6 {7.0} 66.6 {6.8} 66.6 {6.8} 77.4 {7.9} 73.5 {7.5} 73.5 {7.5} 50 N {kgf} 73.5 {7.5} 71.5 {7.3} 71.5 {7.3} 82.3 {8.4} 78.4 {8.0} 78.4 {8.0} REVISE ON PC ONLY D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 6 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION 7. FPC JAPANESE ENGLISH FPC RETENTION FORCE No. of CIRCUIT UNIT RETENTION FORCE (MINIMUM) 1st 10 10th No. of CIRCUIT UNIT RETENTION FORCE (MINIMUM) 1st 10 10th 30 N {kgf} 3.9 {0.40} 3.6 {0.37} 40 N {kgf} 7.6 {0.77} 7.3 {0.74} 32 N {kgf} 4.7 {0.48} 4.3 {0.44} 38 N {kgf} 6.8 {0.69} 6.5 {0.66} 33 N {kgf} 4.9 {0.50} 4.7 {0.48} 43 N {kgf} 8.7 {0.88} 8.4 {0.85} 34 N {kgf} 5.3 {0.54} 5.1 {0.52} 45 N {kgf} 9.4 {0.96} 9.0 {0.92} 35 N {kgf} 5.7 {0.58} 5.4 {0.55} 50 N {kgf} 11.2 {1.14} 10.9 {1.11} 36 N {kgf} 6.1 {0.62} 5.8 {0.59} REVISE ON PC ONLY D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 7 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION O:R 8. JAPANESE ENGLISH INFRARED REFLOW CONDITION 9  245 5 245 5 (PEAK TEMP.) 40 60 (220 ) 40 60 sec.(220 MIN.) O:R (Reflow) 90 120 90 120sec . 150 180 (Pre-heat 150 180 ) N: 6$ X TEMPERATURE CONDITION GRAPH (TEMPERATURE ON BOARD PATTERN SIDE) O:R O:R O:R NOTE; Please check the reflow soldering condition by your own devices beforehand. Because the condition changes by the soldering devices, p.c.boards, and so on. No moisture treatment before reflow process. REVISE ON PC ONLY D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 8 OF 9 EN-37-1(019) PS54132061.doc LANGUAGE PRODUCT SPECIFICATION JAPANESE ENGLISH REV. REV. RECORD DATE EC NO. WRTTN: CH’K: A RELEASED ‘04/09/28 J2005-0939 M.UMEDA K.TOYODA B REVISED ‘04/11/30 J2005-1598 M.UMEDA K.TOYODA C REVISED ‘05/08/04 J2006-0412 N.AIDA K.TOYODA D REVISED ‘05/09/02 J2006-0776 N.AIDA K.TOYODA REVISE ON PC ONLY D SEE SHEET 1 OF 9 REV. DESCRIPTION DOCUMENT NUMBER PS-54132-061 TITLE: 0.5mm PITCH FPC CONN. HSG ASSY FOR SMT BOTTOM CONTACT GOLD PLATING -LEAD FREETHIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX INC. AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION FILE NAME SHEET 9 OF 9 EN-37-1(019) PS54132061.doc