560023-0424

12 11 10 9 7 8 5 6 4 3 2 1 TRADEMARK H H GRIP CODE H G G RADIUS K �3.55� SECTION Y-Y SCALE 20:1 3 NOTES: (UNLESS OTHERWISE SPECIFIED) F 1.3 SECTION X-X SCALE 10:1 PARTIAL 1. MATERIAL: COPPER ALLOY 2. PLATING: SEE TABLE 1 X X F G Y 3. PACKAGING PER PK-31301-319 4. CRIMPING PER AS-560023-001 �5.4� PITCH E RADIUS J 5. PROBING THE CONTACT INTERFACE OF THE TERMINAL OR AT ANY POINT ON THE TERMINAL BEAM IS NOT PERMITTED 1 ±0.05 Y 3.55 ±0.05 �P� D N M Z 1.55 ±0.05 0.40 ±0.05 1.3 ±0.05 Z C �1.2� L LARGE GRIP SHOWN C TABLE 1 B 1.20 1.05 1.05 1.40 1.20 1.05 1.40 1.65 1.27 1.32 1.65 1.65 1.32 1.65 = 0 = 0 = 0 2.25 1.90 1.90 2.35 2.25 1.90 2.35 0.45 0.34 0.24 0.40 0.45 0.24 0.40 0.47 0.41 0.41 0.68 0.47 0.41 0.68 0.00 0.00 0.00 0.15 0.00 0.00 0.15 2.00 2.00 2.50 2.50 2.00 2.50 2.50 2.4 2.4 2.2 2.2 2.4 2.2 2.2 1.4 1.4 1.1 1.1 1.4 1.1 1.1 *SMALL GRIP CHANGE (SEE NOTE 6) 12 11 10 9 8 7 6 = 0 = 0 = 0 H1 = C 2017/03/10 0 0 5 REV 0.22 0.13 0.13 0.35 0.22 0.13 0.35 -0.15 = EC NO: 114242 DRWN: JBURGIO CHK'D: APPR: TOMSMITH M S S L M S L QUALITY THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE SYMBOLS 2017/03/07 H J K L M N P WIRE INSULATION G GRIP GAGE MAX O.D. CODE +0.20 mm 2 mm ± 0.20 ± 0.10 ± 0.20 ± 0.05 ± 0.10 ± 0.10 REF EC DESCRIPTION Plating STATUS D-WIND B-WIND (LEFT PAYOFF) (RIGHT PAYOFF) DEFAULT 560023-0421 560023-0423 Sn 560023-0422* 560023-0424* Sn SALEABLE 560023-0444 560023-0445 Sn 560023-0448 560023-0450 Sn Au 560023-0521 560023-0523 IN VALIDATION Au 560023-0544 560023-0545 Au 560023-0548 560023-0550 SALEABLE FORMAT: Eng-lega-master-tb-prod-C REVISION: A DATE: 2015/09/01 B DIM DIM DIM DIM DIM DIM DIM DIM PART NUMBERS A 6. -0422, -0424 TO BE DISCONTINUED AND REPLACED WITH -0444, -0445 -0444, -0445 VALIDATED TO USCAR21 REV3 SECTIONS 4.3, 4.4, & 4.5.2. ⌀ 1.2 5.8 5 ±0.05 D SECTION Z-Z SCALE 20:1 E GENERAL TOLERANCES (UNLESS SPECIFIED) MM INCH MM 15:1 DRWN BY DATE 2009/05/02 4 PLACES ± --- ± --- TJSMITH 3 PLACES ± --- ± --- CHK'D BY 2 PLACES ± 0.10 ± --- DNICHOLAS 1 PLACES ± 0.10 ± --- APPR BY 0 PLACES ± --- ± --- ANGULAR TOL ± 5 BMOSER DRAWING SIZE DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 4 CTX50 RECEPTACLE TERMINAL UNSEALED DATE 2009/05/20 DATE PRODUCT CUSTOMER DRAWING 2009/05/20 THIRD ANGLE PROJECTION C MATERIAL NUMBER SERIES 560023 SEE TABLE GENERAL MARKET DOC TYPE DOC PART SHEET NUMBER DOCUMENT NUMBER SD-560023-002 3 CUSTOMER 2 PSD 1 OF 2 000 1 A