560123-0500

PRODUCT SPECIFICATION NEW 2.0 W/B CONN REC. HOUSING DURACLIKTM ISL SERIES 1.0 SCOPE This specification covers the 2.0mm PITCH Wire to Board Connector series. (SMT Type) for Automotive. Articles which are not included in this specification can be written in the drawings and they are prior to this specification. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) D NO P/ NUMBER DESCRIPTION REMARK COLOR 1 560123-020* DURACLIK™ ISL HOUSING 2P HOUSING WHITE/ BLACK/RED/BLUE 2 560123-030* DURACLIK™ ISL HOUSING 3P HOUSING WHITE/ BLACK/RED/BLUE 3 560123-040* DURACLIK™ ISL HOUSING 4P HOUSING WHITE/ BLACK/RED/BLUE 4 560123-050* DURACLIK™ ISL HOUSING 5P HOUSING WHITE/ BLACK 5 560123-060* DURACLIK™ ISL HOUSING 6P HOUSING WHITE/ BLACK/RED/BLUE 6 560123-080* DURACLIK™ ISL HOUSING 8P HOUSING WHITE/ BLACK/RED/BLUE 7 560123-090* DURACLIK™ ISL HOUSING 9P HOUSING WHITE 8 560123-100* DURACLIK™ ISL HOUSING 10P HOUSING WHITE 9 560123-120* DURACLIK™ ISL HOUSING 12P HOUSING WHITE 10 560124-01** DURACLIK™ ISL TERMINAL TERMINAL TIN/GOLD 11 560125-020* DURACLIK™ ISL RETAINER 2P RETAINER GRAY 12 560125-030* DURACLIK™ ISL RETAINER 3P RETAINER BLACK/GRAY 13 560125-040* DURACLIK™ ISL RETAINER 4P RETAINER GRAY 14 560125-050* DURACLIK™ ISL RETAINER 5P RETAINER GRAY 15 560125-060* DURACLIK™ ISL RETAINER 6P RETAINER BLACK/GRAY 16 560125-080* DURACLIK™ ISL RETAINER 8P RETAINER GRAY 17 560125-090* DURACLIK™ ISL RETAINER 9P RETAINER GRAY 18 560125-100* DURACLIK™ ISL RETAINER 10P RETAINER GRAY 19 560125-120* DURACLIK™ ISL RETAINER 12P RETAINER GRAY 20 502352-**** WAFER ASSEMBLY (R/A) HEADER NATURAL 21 560020-**** WAFER ASSEMBLY (ST) HEADER NATURAL REVISION: D ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 1 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC PRODUCT SPECIFICATION 3.0 RATINGS AND APPLICABLE WIRES 3.1 APPLICATION ITEM STANDARDS Rated Voltage (Max.) Rated Current (Max.) 125V AVSS 0.3SQ 3.0A Ambient temperature range AC (rms) / DC Insulation Diameter 1.4mm MAX. - 40℃ to 125℃ *. Remark: Including terminal temperature rise. 4.0 STORAGE CONDITIONS -. Storage temperature: - 20 ~ + 60℃ 4.1 STORAGE DURATION -. 6 Months after delivery date REVISION: D ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 2 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC PRODUCT SPECIFICATION 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM DESCRIPTION TEST CONDITION REQUIREMENT 1 Contact Resistance Mate connectors, measure by dry circuit, 20mV MAX., 10mA. (JIS C5402 5.4) 10 milliohm MAX. 2 Insulation Resistance Connectors shall be mated and apply 500V DC between adjacent terminals or ground. (JIS C5402 5.2/MIL-STD-202 Method 302) 1000 mega ohm MIN 3 Dielectric Strength Connectors shall be mated and apply 500V AC (rms) for 1 minute between adjacent terminals or ground.(JIS C5402 5.1/MIL-STD-202 Method 301) 4 Contact Resistance on Crimped Portion Crimped the applicable wire on to the terminal, measure by dry circuit, 20mV MAX., 10mA. Voltage Drop Measure voltage drop by 12±1V of open circuit and 1±0.05A of short circuit at the 75or100mm of point from crimped section. Subtract wire conductor resistance from total resistance. 5 No breakdown 5 milliohm MAX. 10mV/A MAX. 5.2 MECHANICAL REQUIREMENTS ITEM TEST CONDITION REQUIREMENT See paragraph 6. 1 Insertion and Withdrawal Force Insert and withdraw connectors at the speed rate of 25±3mm/minute. 2 Crimping Pull Out Force Fixed crimped terminal, apply axial pull out AVSS force on the wire at the speed rate of 0.3SQ 25±3mm/minute. (JIS C5402 6.8) 3 Terminal Insertion Force 4 Terminal / Housing Retention Force Apply axial pull out force at the speed rate of 25±3mm/minute on the terminal assembled in the housing. 50 N {5.1kgf} MIN. 5 Pin Retention Force Apply axial push force at the speed rate of 25±3mm/minute. 9.8 N {1.0kgf} MIN. 6 Fitting Nail Peeling Strength Mount product on PCB only by fitting nails and apply axial pull-up force at the speed rate of 2.5mm/min. 7 Housing / Wafer Retention Force Mate connectors and apply pull-out force at the speed rate of 25±3mm/min. This test should be done with positive lock locked. REVISION: D DESCRIPTION Insert the crimped terminal into the housing. ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: 50N {5.1 kgf} MIN. 9.8 N {1.0kgf} MAX. 100 N {10.2kgf} MIN. (With both nails) 50N {5.1kgf} MIN. DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 3 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC PRODUCT SPECIFICATION 5.3 ENVIRONMENTAL REQUIREMENTS AND OTHERS ITEM DESCRIPTION TEST CONDITION 1 Repeated Insertion/ Withdrawal When mated up to 30 cycles repeatedly by the rate of 10 cycles/minute. 2 Temperature Rise Carrying rated current load. (UL 498) 2 3 Vibration Acceleration : 44m/s Sweep time: 20-200-20Hz in 3minutes Duration : 3hours in each X, Y, Z axes Open circuit voltage: 20mV max. Short circuit current: 10mA max. 2 4 5 6 Mechanical Shock 981m/s (100G), 3 strokes in each X, Y, Z axes. Operation time: 6ms Heat Resistance 125±2℃,96 hours. (JIS C0021/ MIL-STD-202 method 108) Cold Resistance -40±3℃,96 hours. (JIS C0020) Temperature: 60±2℃ 7 REVISION: D Humidity Relative Humidity: 90-95％ Duration: 96 hours (JIS C0022/MIL-STD-202 Method 103) ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: REQUIREMENT Contact Resistance 20 milliohm MAX. Temperature Rise 30 ℃ MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Voltage Drop 20 mV/A MAX. Discontinuity 1 microsecond MAX. Appearance No Damage Discontinuity 1 microsecond MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Dielectric Strength Must meet 5.1.3 Insulation Resistance 100 mega ohm MIN. DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 4 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC PRODUCT SPECIFICATION 5.3 ENVIRONMENTAL REQUIREMENTS AND OTHERS (continued) ITEM DESCRIPTION TEST CONDITION REQUIREMENT 1000 cycles of 8 9 Temperature Cycling Salt Spray 10 SO2 gas 11 Solder-ability a) -30℃: 30 minutes b) +80℃: 30 minutes 48±4 hours exposure to a salt spray from the 5±1% solution at 35±2 ℃ (JIS C0023/MIl-STD-202 Method 101) 24 hours exposure to 50±5 ppm. SO2 gas at 40±2℃ Soldering Time: 3±0.5 sec. Solder Temperature: 245±5℃ Refer soldering method See paragraph 7. 12 Resistance to Soldering Heat Press the solder trowel of 350±5℃ for 3sec. 13 REVISION: D Twisting Durability Repeat inserting and removing the connector 10 times while twisting it upward, downward, to the right and the left by hands. ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: Appearance No Damage Insertion and Withdrawal Feeling No scratches Terminal / Housing Retention Force Must meet 5.2.4 Crimping Pull Out Force Must meet 5.2.2 Housing / Wafer Retention Force 50 N {5.1kgf} MIN. Contact Resistance 20 milliohm MAX. Voltage Drop 20mV/A MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Solder Wetting 90% of immersed area must show no voids, pinholes. Appearance No Damage Contact Resistance 20 milliohm MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. Appearance No Damage Contact Resistance 20 milliohm MAX. DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 5 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC PRODUCT SPECIFICATION 6.0 INSERTION / WITHDRAWAL FORCE (REFER TO PS-50515-001) D Insertion Force (MAX.) No.of CKT. REVISION: D Withdrawal Force(MIN.) UNIT 1st 6th 30th 1st 6th 30th 2 N {kgf} 35.2 {3.6} 33.3 {3.4} 33.3 {3.4} 1.0 {0.10} 1.0 {0.10} 1.0 {0.10} 3 N {kgf} 43.1 {4.4} 40.1 {4.1} 40.1 {4.1} 1.5 {0.15} 1.5 {0.15} 2.1 {0.21} 4 N {kgf} 50.9 {5.2} 47.0 {4.8} 47.0 {4.8} 2.0 {0.20} 2.0 {0.20} 3.2 {0.33} 5 N {kgf} 58.8 {6.0} 53.9 {5.5} 53.9 {5.5} 2.8 {0.29} 2.8 {0.29} 3.7 {0.38} 6 N {kgf} 64.6 {6.6} 58.8 {6.0} 58.8 {6.0} 3.5 {0.36} 3.5 {0.36} 4.2 {0.43} 7 N {kgf} 70.5 {7.2} 63.7 {6.5} 63.7 {6.5} 3.9 {0.40} 3.9 {0.40} 4.6 {0.47} 8 N {kgf} 76.4 {7.8} 68.6 {7.0} 68.6 {7.0} 4.2 {0.43} 4.2 {0.43} 5.0 {0.51} 9 N {kgf} 82.3 {8.4} 73.5 {7.5} 73.5 {7.5} 4.7 {0.48} 4.7 {0.48} 5.4 {0.55} 10 N {kgf} 88.2 {9.0} 78.4 {8.0} 78.4 {8.0} 5.3 {0.54} 5.3 {0.54} 5.8 {0.59} 11 N {kgf} 94.0 {9.6} 83.3 {8.5} 83.3 {8.5} 5.8 {0.59} 5.8 {0.59} 6.2 {0.63} 12 N {kgf} 99.9 {10.2} 88.2 {9.0} 88.2 {9.0} 6.4 {0.65} 6.4 {0.65} 6.6 {0.67} 13 N {kgf} 107.6 {11.0} 94.9 {9.7} 94.9 {9.7} 6.7 {0.68} 6.7 {0.68} 7 {0.71} 14 N {kgf} 113.9 {11.6} 100.2 {10.2} 100.2 {10.2} 7.2 {0.73} 7.2 {0.73} 7.4 {0.75} 15 N {kgf} 120.2 {12.3} 105.6 {10.8} 105.6 {10.8} 7.7 {0.79} 7.7 {0.79} 7.8 {0.80} ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 6 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC PRODUCT SPECIFICATION 7.0 INFRARED REFLOW CONDITION 8.0 INSTRUCTION UPON USAGE 1) Positive lock should be released when unmating connectors. 2) Connectors should be mated straightly. Angled mating operation has possibility of deforming pins 9.0 NOTES 1) 2) 3) 4) Mounting performance doesn't contain the influence of the warp of PCB. Repairing with soldering iron should be done in specified condition. It is necessary to consult separately when mount product on a special PCB or FPC. There is no influence in the product performance though the twist might be generated in the terminal plating part according to the reflow condition. 5) There is no influence in the product performance though discoloration might be generated in the resin according to the reflow condition. 6) There is no influence in the product performance though black spots are seen on the surface of the resin of this product. 7) There is no influence in the product performance though scratches are seen on the surface of the resin of this product. 8) Coplanarity is assured only before mounting. 9) Changing recommended pattern causes problems. 10) Thickness 0.15mm, aperture ratio 100% metal mask is used in thin specification. REVISION: D ECR/ECN INFORMATION: EC No: 111723 DATE: 2016 / 12 / 21 DOCUMENT NUMBER: PS-560123-002 TITLE: DURACLIK™ ISL W/B CONN. PRODUCT SPECIFICATION SHEET No. 7 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: SJ LEE BC YOON JH JANG TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.2).DOC