67298-4091

PRODUCT SPECIFICATION USB DUAL STACKED A TYPE RECEPTACLE 1.0 SCOPE This Product Specification covers the USB connector series with terminal tin plating and cover selective plating for Non IR reflow process. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) USB DUAL STACKED A TYPE RECEPTACLE 67298-309 ; 67298-409 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS See the appropriate sales drawings for information on dimensions, materials, plating and markings. 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS MIL-STD-1344A EIA-STD- 202 EIA-364 4.0 RATINGS OF CONNECTOR 1. Rate Voltage: 30 V DC Rate Current: 1.5 A DC 2. Operating temperature: 0°C to +50°C Storage temperature : -20°C to +60°C REVISION: ECR/ECN INFORMATION: TITLE: SH2005-0297 EC No: A SHEET No. USB DUAL STACKED A TYPE RECEPTACLE DATE: 1 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS DESCRIPTION TEST CONDITION REQUIREMENT Contact Resistance Mate connectors: apply a maximum voltage of 20 mV and a current of 100 mA. Insulation Resistance Unmated connector, mounted to a PCB: apply a voltage of 500 VDC between adjacent terminals and between terminals to ground. 1000 Megohms MINIMUM Dielectric Withstanding Voltage 750 VAC rms (1mA cutoff current) for 60 seconds duration between adjacent terminals and terminals. No Breakdown Capacitance Test between adjacent contacts to 1 Megahertz max per EIA-364. 30 milliohms MAXIMUM 2 picofarad MAXIMUM Mate connector and measure the Current Temperature temperature rise at the rated current Rating (1.5Amps). 30 rise MAXIMUM from initial 5.2 MECHANICAL REQUIREMENTS DESCRIPTION TEST CONDITION REQUIREMENT 3.57Kgf (35 N) MAXIMUM mate force 1.02 Kgf (10 N) MINMUM unmate force Connector Mate and Mate connector at a rate of Unmate Force 25 ± 6 mm (1 ± ¼ inch) per minute. Terminal Retention Vibration Mechanical Shock Apply a pull out force in the axial direction of the contact per Mil-STD-1344A method 2007.1 0.8 Kgf minimum Mated connector and subject to the following Contact Resistance 30 vibration condition, for a period of 15 minutes milliohms MAXIMUM in each 3 mutually perpendicular axes. Per 1usec EIA-364-28,Test condition V,Test letter A. Discontinuity Subject mated connector to 30 G half sine in 11 msec according to EIA-364-27. Contact Resistance 30 milliohms MAXIMUM Discontinuity REVISION: ECR/ECN INFORMATION: TITLE: SHEET No. SH2005-0297 EC No: A 1usec USB DUAL STACKED A TYPE RECEPTACLE DATE: 2 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION Durability Mate this connector with it’s mating part of 1500 cycles. Other conditions follow per EIA364-09. Contact Resistance 30 milliohms MAXIMUM 5.3 ENVIRONMENTAL REQUIREMENTS DESCRIPTION Mate connectors; Temperature: 40 2 Relative humidity: 90-95% Duration time: 168 hours Solderability Dip solder tails into the molten solder (held at Solderable area shall have 245 ± 5 ) up to 1.0mm from the bottom of minimum of 95 solder the housing for 3 ± 0.5 seconds coverage Thermal Shock Solder Resistance Contact Resistance 30 milliohms MAXIMUM Subject mated connector to ambient temperature 125°C for 250 hours. Per MilSTD-1344A method 1005.1 condition B Contact Resistance 30 milliohms MAXIMUM Subject mated connector to 10 cycles of exposure at -55°C and 85°C per EIA-364-32. Contact Resistance 30 milliohms MAXIMUM Dip connector terminal tails in solder: Solder Duration: 5±0.5 seconds Solder Temperature: 260±5°C Solder Iron Duration: 4-5 seconds Solder IronTemperature: 350±10°C per MIL-STD-202F Appearance : No damage ECR/ECN INFORMATION: TITLE: SHEET No. SH2005-0297 EC No: A REQUIREMENT Steady State Humidity Temperature Life (Thermal Aging) REVISION: TEST CONDITION USB DUAL STACKED A TYPE RECEPTACLE DATE: 3 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 5.4 TEST GROUP GROUP I Examination of product Mating force Contact Resistance Durability Vibration Mechanical shock Contact resistance Unmating force Examination of product REVISION: ECR/ECN INFORMATION: TITLE: SH2005-0297 EC No: A SHEET No. USB DUAL STACKED A TYPE RECEPTACLE DATE: 4 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION GROUP II Examination of product Contact Resistance Temperature life (a) Contact Resistance Examination of product (a): pre-mating and unmating 10 cycles REVISION: ECR/ECN INFORMATION: TITLE: SH2005-0297 EC No: A SHEET No. USB DUAL STACKED A TYPE RECEPTACLE DATE: 5 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION GROUP III Examination of product Capacitance Insulation resistance Dielectric withstanding voltage Thermal shock Steady State Humidity Insulation resistance Dielectric withstanding voltage Examination of product REVISION: ECR/ECN INFORMATION: TITLE: SH2005-0297 EC No: A SHEET No. USB DUAL STACKED A TYPE RECEPTACLE DATE: 6 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 6.0 PACKAGING Parts shall be packaged to protect against damage during handling, transit and storage. See appropriate sales drawings. 7.0 OTHER INFORMATION N/A REVISION: ECR/ECN INFORMATION: TITLE: SH2005-0297 EC No: A SHEET No. USB DUAL STACKED A TYPE RECEPTACLE DATE: 7 of 7 2005/03/14 DOCUMENT NUMBER: PS-67298-001 CREATED / REVISED BY: CHECKED BY: APPROVED BY: JESSICA CHEN TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC