73415-3310

12 11 10 9 7 8 5 6 4 3 2 MATERIALS AND FINISHES H 1 KAPTON ON 73415-3318 ONLY BODY: BRASS PLATED: GOLD (8 µ-in MIN) OVER NICKEL (80 µ-in MIN) H CONTACT: BRASS PLATED: GOLD (30 µ-in MIN) OVER NICKEL (100 µ-in MIN) INSULATOR: PEEK OR LCP G G KAPTON TAPE DOT: POLYMIDE FILM COLOR BLACK (ON -3318 ONLY) .016 0.40 REF TAPE & REEL: SEE SHEETS 2/3 .047 1.20 REF F .083 2.11 REF .019 0.47 REF ⌀ .161 REF A A F 4.10 ⌀ .315 .002 0.04 REF 50 OHM MICROSTRIP E 8.00 REF .100 2.54 REF ⌀ .047 REF E ⌀ .236 SQ .200 5.08 REF 6.00 REF SQ .027 REF 0.69 4 PLACES 1.19 4 PLACES D D ⌀ .177 REF 4.50 R/P RECOMMENDED PCB LAYOUT .051 ±.003 1.30 ±0.08 SQ .236 6.00 C B A C 73415-3318 2.50 / .098 73415-3317 1.70 / .067 73415-3316 2.50 / .098 73415-3315 3.43 / .135 73415-3314 3.43 / .135 73415-3313 1.70 / .067 73415-3312 1.70 / .067 73415-3311 2.50 / .098 73415-3310 2.50 / .098 PART NO. DIM A (MM/IN) 73415-3310 WITH KAPTON (750 PARTS PER REEL) ONE PER BAG (73415-3313) ONE PER BAG (73415-3311) TRAY (73415-3314) TAPE & REEL (750 PARTS PER REEL) TRAY (73415-3312) TAPE & REEL (750 PARTS PER REEL) TRAY (73415-3310) TAPE & REEL (750 PARTS PER REEL) DESCRIPTION PS-89675-3320 PRODUCT SPECIFICATION MIL-STD-348B, FIG. 326.3 INTERFACE SPECIFICATION DESCRIPTION DOCUMENT STATUS 12 FORMAT: Eng-lega-master-tb-prod-C REVISION: E DATE: 2020/01/14 P1 RELEASE DATE 11 2020/09/03 10 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE INCH/MM NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± B11 2020/8/21 ADD -3318 PER EWR #13990-A B10 2013/10/16 ADD -3317 REV DATE DESCRIPTION INCH 0.25 ± ± ± 0 PLACES ± ± 1 PLACE ANGULAR TOL 0.01 ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 11:59:48 9 8 7 6 5 EC NO: 643951 DRWN: SSSHAH CHK'D: YCHENG APPR: YCHENG INITIAL REVISION: DRWN: JMASTRIANO APPR: JWIENER THIRD ANGLE PROJECTION 4 2020/01/02 2020/09/03 2020/09/03 SMP PLUG STRAIGHT PCB LIMITED DETENT, EWR-1359 SMP-P/PCB PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2005/12/09 2005/12/09 DRAWING SERIES C-SIZE 73415 3 SD-73415-331 MATERIAL NUMBER CUSTOMER PSD 001 C10 SHEET NUMBER SEE TABLE 1 OF 3 2 1 A 12 11 10 9 7 8 NOTE 1. 10 PIECES CUMULATIVE TOLERANCE ±0.20[.008] ⌀ .059 H 4 .472 12.00 TYP 1.50 TYP D 5 6 3 2 .157 4.00 TYP .079 2.00 TYP 1 .069 1.75 TYP A H .295 7.50 TYP .630 16.00 G G D FOR 73415-3318 SECTION D-D ⌀ .059 .472 12.00 TYP 1.50 TYP F A FOR 73415-3310 SECTION A-A .157 4.00 TYP .079 2.00 TYP .069 1.75 TYP B F .453 11.50 TYP .945 24.00 E E B FOR 73415-3312 D ⌀ .059 .472 12.00 TYP 1.50 TYP SECTION B-B .157 4.00 TYP .079 2.00 TYP D .069 1.75 TYP C .453 11.50 TYP .945 24.00 C B C FOR 73415-3314 C SECTION C-C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE INCH/MM NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± A 0.25 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 12 P1 RELEASE DATE 11 2020/09/03 10 0.01 ± ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-C REVISION: E DATE: 2020/01/14 INCH ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 11:59:48 9 8 7 6 5 EC NO: 643951 DRWN: SSSHAH CHK'D: YCHENG APPR: YCHENG INITIAL REVISION: DRWN: JMASTRIANO APPR: JWIENER THIRD ANGLE PROJECTION 4 2020/01/02 2020/09/03 2020/09/03 SMP PLUG STRAIGHT PCB LIMITED DETENT, EWR-1359 SMP-P/PCB PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2005/12/09 2005/12/09 DRAWING SERIES C-SIZE 73415 3 SD-73415-331 MATERIAL NUMBER CUSTOMER PSD 001 C10 SHEET NUMBER SEE TABLE 2 OF 3 2 1 A 12 11 10 9 8 7 5 6 4 3 2 1 75 EMPTY UNITS MINIMUM H H ORDER QUANTITY PACKED WITH 750 PARTS 40 EMPTY UNITS MINIMUM LABEL: -ORDER NUMBER -QUANTITY -PART NUMBER -LOT NUMBER G G .230 5.84 MIN ⌀ 12.993 F HANDLING DIRECTION 330.02 F FOR 73415-3310 73415-3312 73415-3314 73415-3318 E E DETAIL E SCALE 2:1 E FOR 73415-3310 D DETAIL F SCALE 2:1 C D DETAIL H SCALE 2:1 DETAIL G SCALE 2:1 G F H FOR 73415-3318 FOR 73415-3314 FOR 73415-3312 C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE INCH/MM NTS CURRENT REV DESC: GENERAL TOLERANCES (UNLESS SPECIFIED) MM 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± A 0.25 ± 0 PLACES ± ± ANGULAR TOL DOCUMENT STATUS 12 P1 RELEASE DATE 11 2020/09/03 10 0.01 ± ± 1 PLACE FORMAT: Eng-lega-master-tb-prod-C REVISION: E DATE: 2020/01/14 INCH ± 2.0 ° DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 11:59:48 9 8 7 6 5 EC NO: 643951 DRWN: SSSHAH CHK'D: YCHENG APPR: YCHENG INITIAL REVISION: DRWN: JMASTRIANO APPR: JWIENER THIRD ANGLE PROJECTION 4 2020/01/02 2020/09/03 2020/09/03 SMP PLUG STRAIGHT PCB LIMITED DETENT, EWR-1359 SMP-P/PCB PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2005/12/09 2005/12/09 DRAWING SERIES C-SIZE 73415 3 SD-73415-331 MATERIAL NUMBER CUSTOMER PSD 001 C10 SHEET NUMBER SEE TABLE 3 OF 3 2 1 A