73415-5190

12 11 10 9 MATERIALS AND FINISHES H 7 8 5 6 4 3 2 1 ⌀ .150 3.80 BODY: ZINC ALLOY PLATED NICKEL (70 µ-in MIN) H CENTER CONTACT: BRASS PLATED GOLD (10 µ-in MIN) .315 REF 8.00 INSULATOR: PTFE OUTER CONTACT: BERYLLIUM COPPER PLATED GOLD (10 µ-in MIN) G G CRIMP TUBE: BRASS PLATED NICKEL (70 µ-in MIN) ⌀ .142 ⌀ .197 3.61 REF 5.00 REF CAP: STAINLESS STEEL PASSIVATED .368 REF 9.34 F F E E MCX PLUG 75 OHM INTERFACE D D .197 REF 5.00 SQUARE C C .409 REF 10.40 PART # 73415-5190 B B SEE SHEET 2 FOR ASSEMBLY INSTRUCTIONS SYMBOLS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE CURRENT REV DESC: = 0 IN/MM = 0 = 0 = 0 = A = DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2019/12/02 10 C 22:00:46 9 8 7 6 0 0 = 0 = 0 = 0 NTS GENERAL TOLERANCES (UNLESS SPECIFIED) MM INCH 4 PLACES ± ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 0.01 2.0 ° EC NO: MCX PLUG, R/A FOR RG179 75 OHMS, MCX-PC, EWR-13455 628146 DRWN: LMEIER CHK'D: SSSHAH APPR: AROBERTSON INITIAL REVISION: DRWN: TEF APPR: JDW THIRD ANGLE PROJECTION 4 2019/11/20 2019/12/02 2019/12/02 PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2004/10/27 2004/10/27 DRAWING SERIES C-SIZE 73415 3 A DOC TYPE DOC PART REVISION SD-73415-519 MATERIAL NUMBER CUSTOMER PSD 001 A1 SHEET NUMBER 734155190 1 OF 2 2 1 12 11 10 9 8 7 5 6 1. SLIDE CRIMP TUBE ONTO CABLE BEFORE CABLE STRIP OPERATIONS. NOTE ORIENTATION OF CRIMP TUBE. STRIP CABLE PER DIMENSIONS SHOWN. 4 3 2 1 4. CRIMP CONNECTOR USING A .160 [4.06] HEX CRIMP TOOL. INSERT CAP INTO OPENING IN REAR OF BODY AS SHOWN. NOTE ORIENTATION OF CAP. H H CRIMP TUBE .363 REF 9.23 JACKET INSERT CAP .127 REF 3.23 BRAID G G .034 REF 0.87 DIELECTRIC F RECOMMENDED CABLE STRIP FOR RG179 CABLE F 2. FLARE CABLE BRAID. INSERT CABLE INTO CONNECTOR UNTIL CABLE CENTER CONDUCTOR IS INSERTED THROUGH SLOT IN CONTACT AND CABLE DIELECTRIC BOTTOMS AGAINST CONTACT AS SHOWN. SOLDER CABLE CENTER CONDUCTOR TO CONNECTOR CONTACT. .160 HEX 4.06 SOLDER E E 5. SUPPORT CONNECTOR ON SURFACE SHOWN AND PRESS CAP INTO REAR OPENING IN BODY PER AS-89675-507. ENSURE CABLE DIELECTRIC IS BOTTOMED D PRESS CAP D FLARE BRAID C C 3. SLIDE CRIMP TUBE FORWARD UNTIL FLUSH AGAINST FACE OF BODY AS SHOWN. SUPPORT CONNECTOR HERE FLUSH B B SYMBOLS THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE CURRENT REV DESC: = 0 IN/MM SLIDE CRIMP TUBE FORWARD = 0 = 0 = 0 = A = DOCUMENT STATUS 12 FORMAT: IN-master-tb-prod-C REVISION: C DATE: 2018/01/18 P1 RELEASE DATE 11 2019/12/02 10 C 22:00:46 9 8 7 6 0 0 = 0 = 0 = 0 NTS GENERAL TOLERANCES (UNLESS SPECIFIED) MM INCH 4 PLACES ± ± 3 PLACES ± ± 0.005 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ANGULAR TOL ± ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 5 0.01 2.0 ° EC NO: MCX PLUG, R/A FOR RG179 75 OHMS, MCX-PC, EWR-13455 628146 DRWN: LMEIER CHK'D: SSSHAH APPR: AROBERTSON INITIAL REVISION: DRWN: TEF APPR: JDW THIRD ANGLE PROJECTION 4 2019/11/20 2019/12/02 2019/12/02 PRODUCT CUSTOMER DRAWING DOCUMENT NUMBER 2004/10/27 2004/10/27 DRAWING SERIES C-SIZE 73415 3 A DOC TYPE DOC PART REVISION SD-73415-519 MATERIAL NUMBER CUSTOMER PSD 001 A1 SHEET NUMBER 734155190 2 OF 2 2 1