74754-0220

12 11 10 9 8 7 5 6 4 3 2 1 3D MODEL : 1111122220 PSM ASY BASE CAGE DETAILS 29.4 (OUTSIDE TABS) H 747540220 H INNER WALL IS COINED OVER BASE AND COVER FOR EXTRA RIGIDITY EMI SPRING FINGERS G G 49.0 REF (OVERALL LENGTH) F F UNDERBELLY SPRING FINGERS E E 4 30.15 REF (EMI FINGERS UNCOMPRESSED) 49.0 REF 28.25 REF (INSIDE TO INSIDE) D D 4 10.85 REF (EMI FINGERS UNCOMPRESSED) 2X 8.95 ±0.10 (INSIDE TO INSIDE) XXXXXXXXXXWWYY 3.05 TYP C C 2X 14.0 ±0.1 (INSIDE TO INSIDE) B A 11.50 REF PN/DATE CODE TO BE PRINTED ON THE BACK OF COMPLETED CAGE ASSEMBLY APPROXIMATELY AS SHOWN. FOR 74754 SERIES CAGE (747540247 NO NEED PRINTED) WEEK/YEAR DATE CODE TABLE WW WEEK OF THE YEAR 01 THRU 52 (EXAMPLE:01= FIRST WEEK OF YEAR 52=LAST WEEK OF YEAR) YY 16, 17, 18 ETC. EXAMPLE: YEAR 2016 = 16 NOTES: 1. MATERIAL: CAGE: 0.25mm THICK COPPER ALLOY, NICKEL PLATED. SPRING FINGERS: 0.10mm THICK COPPER ALLOY, NICKEL PLATED. HEATSINK: ALUMINUM, NICKEL PLATED. HEATSINK SPRING CLIP: STAINLESS STEEL. 2. PRESS FIT LEGS 3.05mm LONG 3. PORTS ARE DESIGNED FOR SFP+ TRANSCEIVERS AND ARE COMPATIBLE WITH SFP TRANSCEIVERS. THE TOP SURFACE OF THE MODULE MUST BE FLAT (NO PRODUCT LABEL RECESS) AND THERMALLY CONDUCTIVE TO FUNCTION OPTIMALLY. 4. WELD SPOT MAY SHOW SLIGHT MATERIAL DISCOLORATION. 5. NO RoHS EXEMPTIONS. 6. CUSTOM HEATSINKS AVAILABLE UPON REQUEST. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/11/25 10 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 3:1 12:19:23 8 7 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 9 B 6 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 1 OF 7 1 A 12 11 10 9 7 8 5 6 4 3 2 1 CAGE ASSEMBLY OPTIONS H H OPEN TOP 1111120220 SHOWN (APPLIES TO ALL OPEN TOP CAGES) HEATSINK OPTIONS (2 PLC) HEATSINK OPTIONS (2 PLC) G WIDE GAP NETWORKING LATERAL FIN NETWORKING PIN FIELD NETWORKING 2X 9.00 REF HEATSINK OPTIONS (2 PLC) WIDE GAP SAN HEATSINK OPTIONS (2 PLC) CUSTOM LATERAL FIN SAN PIN FIELD SAN WIDE GAP PCI G LATERAL FIN PCI PIN FIELD PCI 2X 26.5 F F 2X 16.5 OVERALL HEATSINK HEIGHT DIM 'A' DIM 'B' STYLE CUSTOM 20.4 16.7 E OVERALL HEATSINK HEIGHT APPLICATION STYLE DIM 'A' 14.3 16.6 23.6 PIN FIELD PIN FIELD SAN NETWORKING PIN FIELD PCI OVERALL HEATSINK HEIGHT APPLICATION STYLE LATERAL FIELD LATERAL FIELD SAN NETWORKING LATERAL FIELD PCI OVERALL HEATSINK HEIGHT DIM 'A' APPLICATION STYLE DIM 'A' 14.3 16.6 23.6 PCI WIDE GAP PIN WIDE GAP PIN WIDE GAP PIN 14.3 16.6 23.6 SAN NETWORKING E NOTE: PCI - 13 ROWS SAN - 11 ROWS NETWORKING - 10 ROWS HEATSINK OPTIONS CUSTOM FIN D D REAR LEG OPTIONS (PER PORT) C C "A" MAX 1 TYP "B" MAX "A" MAX TYP 1 1A , 1B OVERALL HEATSINK HEIGHT B : P-PIN APPLICATION DIM 'A' CUSTOM 23.6 A : PRESS FIT PN/DATE CODE TO BE PRINTED ON THE SIDE OF COMPLETED CAGE ASSEMBLY APPROXIMATELY AS SHOWN. FOR 111112 SERIES CAGES B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION WEEK/YEAR DATE CODE TABLE WW 01 THRU 52 OR 53 EXAMPLE: 01 = FIRST WEEK OF YEAR 52 = LAST WEEK OF YEAR YY 16, 17, 18 ETC. EXAMPLE: YEAR 2016 = 16 A 1 WITH MODULE INSERTED, DIMENSION MAY BE LESS DUE TO MODULE AND HEATSINK VARIATIONS DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/11/25 10 DIMENSION UNITS SCALE mm 1.5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:23 9 8 7 6 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 2 OF 7 1 A 12 11 10 9 8 7 5 6 4 3 2 1 PART NUMBER SELECTION H H G G PART NO. 747540220 747540222 747540247 F SFP+ CLOSED TOP BASE CAGE DESCRIPTION SFP FOOTPRINT (STD B TO B), 5 WELD POINTS SFP FOOTPRINT (STD B TO B), 16 WELD POINTS SAME AS ABOVE BUT NO PN/DATE CODE PRINTED F SFP+ CUSTOM HEATSINK OPTION SFP+ OPEN TOP BASE CAGE FOR HEATSINK 1111120220 PART NO. PART NO. 1111120226 E E D D C C SFP+ LATERAL FIN HEATSINK OPTION PART NO. APPLICATION 1111127220 PCI B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 1.25:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/11/25 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:23 9 8 7 6 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 3 OF 7 1 A 12 11 10 9 7 8 5 6 4 3 2 1 PCB LAYOUT - SINGLE SIDE ONLY H HATCHED AREA DENOTES COMPONENTS AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND H 14.25 TYP 1.00 2.50 MIN TOP-LEFT HOLE OF ADJACENT CAGE AT MINIMUM SPACING B 7X ⌀ 1.05 ±0.05 ⌖ 0.1 A B A SHOWN AS G 12.05 1.10 0.00 G 4.5 2.00 TYP 9.5 TYP F 14.5 CROSS HATCHED AREA GOES TO CHASSIS GROUND (NO OSP) 2 PLCS 19.5 TYP F 21.60 TYP 24.5 27.3 TYP 29.5 TYP 32.0 1.00 TYP 35.4 TYP 37.0 TYP E E 39.5 TYP 41.6 TYP 42.30 TYP 2.88 TYP D 2.33 TYP D 12.25 TYP 2.00 TYP SEE DETAIL 1 2.88 TYP 7.13 TYP THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) DETAIL 1 SCALE 5:1 11.93 TYP 12X ⌀ 0.95 ±0.05 C C ⌖ 0.1 A B SHOWN AS B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A DOCUMENT STATUS 12 P1 RELEASE DATE 11 2021/11/25 10 8 7 mm 1:1 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:23 9 SCALE CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) NOTES: 1. PADS AND VIAS CONNECT TO CHASSIS GROUND RECOMMEND PADS TO BE 2.00mm SQUARE 2. RECOMMENDED THRU HOLE PLATING INCLUDES HASL, OSP, OR IMMERSION (GOLD, SILVER, OR TIN) 3. CONNECTOR PAD LAYOUT PER SFP+ MSA WILL ACCOMODATE MOLEX CONNECTOR SERIES 74441 OR EQUIVALENT. 4. SPACING BETWEEN PORTS IS 14.25mm 5. 1.57mm MINIMUM PCB THICKNESS FOR SINGLE SIDED USE. FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 DIMENSION UNITS 6 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 4 OF 7 1 A 12 11 10 9 8 7 5 6 4 3 2 1 PCB LAYOUT FOR BELLY TO BELLY MOUNTING H H 1.00 TYP 2.50 MIN HATCHED AREA DENOTES COMPONENTS AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND 14.25 TYP TOP-LEFT HOLE OF ADJACENT CAGE AT MINIMUM SPACING B A G 0.00 G 4.5 TYP 9.5 TYP CROSS HATCHED AREA GOES TO CHASSIS GROUND (NO OSP) 2 PLCS F F 14.5 TYP 19.5 TYP 21.60 TYP 24.5 TYP E E 27.3 TYP 14X ⌀ 1.05 ±0.05 29.5 TYP ⌖ 0.1 A B 32.0 TYP SHOWN AS 35.4 TYP 37.0 TYP D D 39.5 TYP 41.6 TYP 42.30 TYP THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALOWED) C NOTE: SEE SHEET 4 FOR HOST CONNECTOR DETAIL 2.33 TYP 16X ⌀ 0.95 ±0.05 7.13 TYP ⌖ 0.1 A B C SHOWN AS 11.93 TYP B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION A DOCUMENT STATUS 12 P1 RELEASE DATE 11 2021/11/25 10 SCALE mm 4:1 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:23 9 8 7 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) NOTES: 1. PADS AND VIAS CONNECT TO CHASSIS GROUND RECOMMEND PADS TO BE 2.00mm SQUARE 2. RECOMMENDED THRU HOLE PLATING INCLUDES HASL, OSP, OR IMMERSION (GOLD, SILVER, OR TIN) 3. CONNECTOR PAD LAYOUT PER SFP+ MSA WILL ACCOMODATE MOLEX CONNECTOR SERIES 74441 OR EQUIVALENT. 4. SPACING BETWEEN PORTS IS 14.25mm 5. 3.00mm [.118 INCH] MINIMUM PCB THICKNESS FOR BELLY TO BELLY USE. FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 DIMENSION UNITS 6 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 5 OF 7 1 A 12 11 10 9 8 7 5 6 4 3 2 1 BEZEL AND BOARD POSITION DIMENSIONS FOR SINGLE SIDE MOUNTING (SPRING FINGER) H R 0.30 MAX TYP 29.70 ±0.10 H 45.5 REF CUTAWAY 2 G G 10.40 ±0.10 9.98 TYP 0.09 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE 3 1.30 MIN 12.48 REF CUTAWAY 1 F F E E BEZEL AND BOARD POSITION DIMENSIONS FOR BELLY TO BELLY MOUNTING (SPRING FINGER) 2X 45.5 REF R 0.30 MAX TYP D D CUTAWAY 4 0.09 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE (SEE NOTE 1) 10.40 ±0.10 (SEE NOTE 1) 9.98 TYP CUTAWAY 3 12.48 REF SEE NOTE 1 C C 10.40 ±0.10 (SEE NOTE 1) 0.09 ±0.10 BEZEL OPENING ABOVE PCB PAD SURFACE (SEE NOTE 1) A 2X 29.70 ±0.10 3 1.30 MIN B 3.50 ±0.30 B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) A NOTE: 1. PCB THICKNESS VARIATION MUST BE CONSIDERED WHEN DETERMINING BEZEL OPENING SIZE AND LOCATION. 2. CAGE LEG STANDOFF WILL PIERCE BELLY GASKET WHEN PROPERLY PRESSED INTO PCB. 3 THIS DIMENSION IS FOR REF ONLY. USER CAN MODIFY IT DEPENDS ON APPLICATION. HOLE OF ADJACENT CAGE ON PCB LAYOUT VARIES ON MODIFICATION. DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/11/25 10 8 ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:23 9 ANGULAR TOL 7 6 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 6 OF 7 1 A 12 H 11 REV DATE A A1 2011/06/10 2011/06/15 B 2011/07/22 B1 2011/08/19 2012/10/25 C G D 2014/02/07 F E E 2014/08/13 F 2014/08/21 G 2015/02/26 H 2015/08/26 D C J 2016/06/28 J2 2016/12/16 2021/09/22 J3 10 9 8 7 6 5 4 3 2 1 DESCRIPTION INITIAL RELEASE SHEET 1: REMOVED HEATSINK OPENING REFERENCE DIMENSIONS AND WEEK 52 REFERENCE; SHEET 4: ADDED NOTES POINTING TO THE INNER WALL COINED OVER THE COVER. ADDED HOLES IN CAGE FOR LIGHTPIPES; MOVED DATE CODE; REVISED ROHS NOTE 5; CHANGED HEATSINK HEIGHT FROM 8.63 TO 6.5; TABULARIZED PCI, SAN, AND NETWORKING; AND ADDED HEATSINK HEIGHT WITH MODULE INSERTED. UPDATED CAGE AND SPRING CLIP MODELS. SHEET 1: REMOVED HEATSINKS, AND ALL DIMS AND ANNOTATIONS RELATING TO THEM, FROM ALL VIEWS; REMOVED NOTE 6; REMOVED EXPLODED VIEW; REMOVED PART NUMBER TABLE; ADDED TITLE. NEW SHEET 2: ISO VIEWS OF CAGE WITH NO HEATSINKS AND VIEWS WITH EACH OF FOUR TYPES AND SIZES OF HEATSINK; ANNOTATIONS ON EACH VIEW INDICATIING EACH HEATSINK TYPE AND SIZE; RIGHT SIDE VIEW WITH DIM OF HEATSINK HEIGHT; TABLE UNDER EACH VIEW WITH HEATSINK SIZES AND DIMS; NOTE 1; SHEET TITLE. NEW SHEET 3: ISO VIEWS OF CAGE WITH NO HEATSINKS AND VIEWS WITH EACH OF FOUR DIFFERENT TYPES OF HEATSINK; TABLES UNDER EACH VIEW WITH PART NUMBERS OF EACH SIZE; SHEET TITLE. SHEET 1: REVISED ALL BASE CAGE DETAILS AND VIEWS FROM 111112-0232 TO 74754-0220. REMOVED INSERTION FORCE INTO PCB FROM NOTE 2. REVISED NOTE 4: "WAS" WELD SPOT WILL SHOW SLIGHT MATERIAL DISCOLORATION. "NOW READS" WELD SPOT MAY SHOW SLIGHT MATERIAL DISCOLORATION. SHEET 2: REVISED ALL HEAT SINK CAGE ASSEMBLY OPTIONS. ADDED OPEN TOP VIEW WITH DIMENSIONS, AND REAR LEG OPTION VIEW. SHEET 3: ADDED SHEET 3 WITH ZSFP+ OPTIONS SHEET 4: ADDED PART NUMBERS 747540220, 1001130220. UPDATED TITLE BLOCK. SHEET 1: ADDED "REF" TO DIM 10.85 AND 28.25. ADDED 14.0 ± 0.1. MOVED "MINIMUM PCB THICKNESS" NOTES FROM SHEET 1 TO SHEETS 5 AND 6. SHEET 1: ADDED 747540247 NO NEED PRINTED @C6. SHEET 1: ADDED P/N AND DATE CODE PRINTED NOTE @D11. SHEET 4: ADDED P/N 747540247 IN TABLE @I18. SHEET 3: ADDED NOTE 1 "UNDER BELLY GASKET IS UL94 V-0 RATED." SHEET 4: ADDED "5 WELD POINTS" INTO 747540220 @I17. SHEET 4: ADDED P/N 747540222 @I17. SHEET 7: ADDED NOTE 2 "CAGE LEG STANDOFF WILL PIERCE BELLY GASKET WHEN PROPERLY PRESSED INTO PCB." SHEET 2: E3 : ADDED NEW CUSTOM FIN HEATSINK ISO VIEW SHEET 4: E3 : ADDED PART NO. 111112-6221 ISO VIEW MODIFIED PCB LAYOUT PER SFF-8433 SHEET 5: K19 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 D17 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 SHEET 6: G19 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 B18 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 REMASTERED FROM SD-111112-2220 REV H TO "1111122220 REV_J" NX SHEET 2: E10: CHANGED THE PN /DATE CODE STYLE FROM 1 ROW TO 2 ROWS SHEET 7: A19:ADDED A NOTE "THIS DIM IS FOR REF ONLY. USER CAN MODIFY IT DEPENDS ON APPLICATION.HOLE OF ADJACENT CAGE ON PCB LAYOUT VARIES BASED ON MODIFICATION." SEPARATED ZSFP+ SERIES TO 1001130220 PSD ASY SHEET 4/5: CORRECTED TYPO TO UPDATE PCB VIEW OBSOLETED PART NUMBERS 1111121220, 1111122220, 1111123220, 1111124220, 1111125220, 1111126220, 1111126221, 1111128220, 1111129220. SHEET 4: E07: ADDED DIMENSION 35.4 TYP. H G F E D C B B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION DIMENSION UNITS SCALE mm 1:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) A DOCUMENT STATUS 12 FORMAT: master-tb-prod-C REVISION: J DATE: 2020/01/14 P1 RELEASE DATE 11 2021/11/25 10 ANGULAR TOL ± 4 PLACES ± 3 PLACES ± 2 PLACES ± 1 PLACE ± 0 PLACES ± 1.0 ° 0.13 0.25 DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:23 9 8 7 6 5 EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: MKEMPEGOWDA APPR: RCHEN08 THIRD ANGLE PROJECTION 2021/05/26 2021/11/25 2021/11/25 PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2016/04/13 2016/08/04 DRAWING SERIES C-SIZE 111112 4 SFP+ 1X2 CAGE, 3.05 MM PRESS FIT, HEAT SINK, EMI SPRING FINGERS 3 1111122220 MATERIAL NUMBER CUSTOMER PSD ASY SEE SHEET 3 2 J3 SHEET NUMBER 7 OF 7 1 A 20 M 19 18 17 16 15 14 13 12 10 11 9 7 8 6 5 4 3 2 1 M BASE CAGE DETAILS MM 3D-MODEL: TM-111112-2220 29.4 (OUTSIDE TABS) 747540220 EMI SPRING FINGERS L L INNER WALL IS COINED OVER BASE AND COVER FOR EXTRA RIGIDITY K K 49.0 REF (OVERALL LENGTH) J J H H UNDERBELLY SPRING FINGERS G G 30.15 REF (EMI FINGURES UNCOMPRESSED) 28.25 REF (INSIDE TO INSIDE) 49.0 REF F F 8.95 ±0.10 (INSIDE TO INSIDE) 10.85 REF (EMI FINGERS UNCOMPRESSED XXXXXXXXXXWWYY XXXXXXXXXXWWYY E PN/DATE CODE TO BE PRINTED IN APPROXIMATE AREA AS SHOWN. FOR 111112 SERIES CAGE 14.0 ±0.1 (INSIDE TO INSIDE) PN/DATE CODE TO BE PRINTED ON THE BACK OF COMPLETED CAGE ASSEMBLY APPROXIMATELY AS SHOWN. FOR 74754 AND 100113 SERIES CAGE (747540247 NO NEED PRINTED) D C B A E 3.05 WW YY NOTES: 1. MATERIAL: CAGE: 0.25mm THICK COPPER ALLOY, NICKEL PLATED. SPRING FINGERS: 0.10mm THICK COPPER ALLOY, NICKEL PLATED. HEATSINK: ALUMINUM, NICKEL PLATED. HEATSINK SPRING CLIP: STAINLESS STEEL. 2. PRESS FIT LEGS 3.05mm [.120 INCH] LONG 3. PORTS ARE DESIGNED FOR SFP+ TRANSCEIVERS AND ARE COMPATIBLE WITH SFP TRANSCEIVERS. THE TOP SURFACE OF THE MODULE MUST BE FLAT (NO PRODUCT LABEL RECESS) AND THERMALLY CONDUCTIVE TO FUNCTION OPTIMALLY. 4. WELD SPOT MAY SHOW SLIGHT MATERIAL DISCOLORATION. 5. NO ROHS EXEMPTIONS. 6. CUSTOM HEATSINKS AVAILABLE UPON REQUEST. DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 15 14 13 WEEK/YEAR DATE CODE TABLE 01 THRU 52 OR 53 EXAMPLE: 01 = FIRST WEEK OF YEAR 52 = LAST WEEK OF YEAR 11, 12, 13 ETC. EXAMPLE: YEAR 2013 = 13 THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 4:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) MM ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 0 PLACES ± ± ANGULAR TOL ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH 4 PLACES ± 1 PLACE 12:19:18 16 D ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 1 OF 8 1 A 20 19 18 17 16 15 14 13 12 M 10 11 9 7 8 6 5 4 3 2 1 M CAGE ASSEMBLY OPTIONS OPEN TOP 1111120220 SHOWN L L (APPLIES TO ALL OPEN TOP CAGES) 2X 9.00 REF HEATSINK OPTIONS (2 PLC) CUSTOM HEATSINK OPTIONS (2 PLC) PIN FIELD NETWORKING PIN FIELD SAN PIN FIELD PCI K HEATSINK OPTIONS (2 PLC) WIDE GAP NETWORKING WIDE GAP SAN WIDE GAP PCI HEATSINK OPTIONS (2 PLC) LATERAL FIN NETWORKING LATERAL FIN SAN LATERAL FIN PCI K J J 2X 26.5 H H OVERALL HEATSINK HEIGHT OVERALL HEAT SINK HEIGHT STYLE CUSTOM 2X 16.5 DIM 'A' 20.4 DIM 'B' 16.7 APPLICATION PCI SAN NETWORKING G STYLE PIN FIELD PIN FIELD PIN FIELD OVERALL HEATSINK HEIGHT DIM 'A' 14.3 16.6 23.6 OVERALL HEATSINK HEIGHT DIM 'A' APLICATION STYLE LATERIAL FIELD 14.3 PCI LATERIAL FIELD 16.6 SAN NETWORKING LATERIAL FIELD 23.6 APPLICATION PCI SAN NETWORKING TYLE WIDE GAP PIN WIDE GAP PIN WIDE GAP PIN DIM 'A' 14.3 16.6 23.6 G NOTE: PCI- 13 ROWS SAN- 11 ROWS NETWORKING- 10 ROWS HEATSINK OPTIONS CUSTOM FIN REAR LEG OPTIONS F F (PER REPORT) 'A' MAX TYP E "B" MAX ' A ' MAX TYP 1 1A, 1B 1 E OVERALL HEATSINK HEIGHT APPLICATION CUSTOM D B : P-PIN WW YY A : PRESS FIT D WEEK/YEAR DATE CODE TABLE 01 THRU 52 OR 53 EXAMPLE: 01 = FIRST WEEK OF YEAR 52 = LAST WEEK OF YEAR 11, 12, 13 ETC. EXAMPLE: YEAR 2013 = 13 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 3:1 MM B ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 0 PLACES ± ± ANGULAR TOL FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH 4 PLACES ± 1 PLACE DOCUMENT STATUS CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) WITH MODULE INSERTED. DIMENSION MAY BE LESS DUE TO MODULE AND HEATSINK VARIATIONS A DIM 'A' 23.6 ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 2 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 5 6 4 3 2 1 M M 30.98 MAX. (UNDER BELLY GASKET) OPTIONAL GEN 2 zSFP+ UNDER BELLY GASKET L NOTCH IN GASKET FOR ORIENTATION 1001130220 L SHOWN K K 49.73 (TO UNDER BELLY GASKET) J J 9.98 REF TOP OF COIN TO PCB PAD SURFACE (WHEN PRESSED INTO BOARD) H H G G F F E E D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 3.5:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) MM B NOTE: 1. UNDER BELLY GASKET IS UL94 V-0 RATED 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ± ANGULAR TOL A DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 3 OF 8 1 A 20 19 18 17 16 15 14 13 12 M 11 10 9 7 8 6 5 4 3 2 1 M PART NUMBER SELECTION L L K K J PART NO. 747540220 747540222 747540247 J SFP+ CLOSED TOP BASE CAGE DESCRIPTION SFP FOOTPRINT (STD B TO B), 5 WELD POINTS SFP FOOTPRINT (STD B TO B), 16 WELD POINTS SAME AS ABOVE BUT NO PN/DATE CODE PRINTED SFP+ OPEN TOP BASE CAGE FOR HEATSINK PART NO. 1111120220 zSFP+ GEN 2 CLOSED TOP PART NO. 1001130220 SFP+ CUSTOM HEATSINK OPTION PART NO. 1111120226 H H G G F F E E SFP+ LATERAL FIN HEATSINK OPTION PART NO. APPLICATION 1111127220 PCI D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) MM B 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ± ANGULAR TOL A DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 4 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M PCB LAYOUT - SINGLE SIDE ONLY 14.25 TYP 1.00 L 7X ⌀1.05 ±0.05 SEE NOTE 6 2.5 MIN TOP-LEFT HOLE OF ADJACENT CAGE AT MINIMUM SPACING L 12.05 ⌖ 0.1 A B 1.10 B SHOWN AS A 0.0 K K 4.5 9.5 TYP J J 2.00 TYP 14.5 SEE NOTE 5 19.5 TYP 21.60 TYP H H 24.5 27.3 TYP 29.5 TYP 32.0 G G 37.0 TYP 39.5 TYP 41.6 TYP F F 42.30 TYP 1.00 TYP SEE DETAIL 1 2.33 TYP E THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALLOWED) E 7.13 TYP 2.88 TYP 2.88 TYP 12X ⌀0.95 ±0.05 ⌖ 0.1 A B D 2.00 TYP 11.93 TYP D 12.25 TYP SHOWN AS DETAIL 1 SCALE 8:1 C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C NOTES: 1. PADS AND VIAS CONNECT TO CHASSIS GROUND RECOMMEND PADS TO BE 2.00mm SQUARE 2. RECOMMENDED THRU HOLE PLATING INCLUDES HASL, OSP, OR IMMERSION (GOLD, SILVER, OR TIN) 3. CONNECTOR PAD LAYOUT PER SFP+ MSA WILL ACCOMODATE MOLEX CONNECTOR SERIES 74441 OR EQUIVALENT. 4. SPACING BETWEEN PORTS IS 14.25mm 5. CROSS-HATCHED AREA IS EXPOSED CHASSIS GROUND (NO OSP) 6. HATCHED AREA IS COMPONENT AND TRACE KEEP-OUT (EXCEPT CHASSIS GROUND) 7. 1.57mm [.062 INCH] MINIMUM PCB THICKNESS FOR SINGLE SIDED USE. B DIMENSION UNITS SCALE mm 5:1 GENERAL TOLERANCES (UNLESS SPECIFIED) MM ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE ± ANGULAR TOL DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH 4 PLACES ± 0 PLACES ± A CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 5 OF 8 1 A 20 19 18 17 16 15 14 13 M 12 11 10 9 7 8 6 5 4 3 2 1 M PCB LAYOUT FOR BELLY TO BELLY MOUNTING 1.00 TYP HATCHED AREA DENOTES COMPONENTS AND TRACE KEEP-OUT (EXCEPT CHASIS GROUND L 14.25 TYP L TOP-LEFT HOLE OF ADJACENT CAGE AT MINIMUM SPACING 2.50 MIN B A 0.00 K K 4.5 TYP 9.5 TYP J J 14.5 TYP CROSS HATCHED AREA GOES TO CHASIS GROUND (NO OSP) 2 PLCS H H 19.5 TYP 21.60 TYP 24.5 TYP NOTE: SEE SHEET 5 FOR HOST CONNECTOR DETAIL 27.3 TYP G 29.5 TYP 14X ⌀1.05 ±0.05 G 32.0 TYP ⌖ 0.1 A B SHOWN AS 35.4 TYP F F 37.0 TYP 39.5 TYP 41.6 TYP 42.30 TYP E E 2.33 TYP THIS AREA DENOTES COMPONENT KEEP-OUT (TRACES ALOWED) D D 16X ⌀0.95 ±0.05 7.13 TYP ⌖ 0.1 A B SHOWN AS 11.93 TYP C B THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 6:1 GENERAL TOLERANCES (UNLESS SPECIFIED) NOTES: 1. PADS AND VIAS CONNECT TO CHASSIS GROUND RECOMMEND PADS TO BE 2.00mm SQUARE 2. RECOMMENDED THRU HOLE PLATING INCLUDES HASL, OSP, OR IMMERSION (GOLD, SILVER, OR TIN) 3. CONNECTOR PAD LAYOUT PER SFP+ MSA WILL ACCOMODATE MOLEX CONNECTOR SERIES 74441 OR EQUIVALENT. 4. SPACING BETWEEN PORTS IS 14.25mm. 5. 3.00mm [.118 INCH] MINIMUM PCB THICKNESS FOR BELLY TO BELLY USE. MM ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 ± 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH 4 PLACES ± ANGULAR TOL A CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 6 OF 8 1 A 20 19 18 17 16 15 14 13 12 10 11 9 7 8 5 6 4 3 2 1 BEZEL AND BOARD POSITION DIMENSIONS FOR SINGLE SIDE MOUNTING (SPRING FINGER) M 29.70 ±0.10 L M 45.5 REF L K K 12.48 REF 10.40 ±0.10 9.98 TYP Cutaway2 J J 0.09 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE Cutaway1 1.30 MIN H H BEZEL AND BOARD POSITION DIMENSIONS FOR BELLY TO BELLY MOUNTING (SPRING FINGER) 2X 45.52 REF G G 0.09 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE (SEE NOTE 1) F 12.48 REF Cutaway 1 10.40 ±0.10 (SEE NOTE 1) F 9.98 TYP Cutaway3 SEE NOTE 1 E E 10.40 ±0.10 (SEE NOTE 1) D D 0.09 ±0.10 BEZEL OPENING BELOW PCB PAD SURFACE (SEE NOTE 1) C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C 2X 29.70 ±0.10 1.30 MIN 3.50 ±0.30 DIMENSION UNITS SCALE mm 5:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) MM NOTE: 1. PCB THICKNESS VARIATION MUST BE CONSIDERED WHEN DETERMINIG BEZEL OPENING SIZE AND LOCATION. 2. CAGE LEG STANDOFF WILL PIERCE BELLY GASKET WHEN PROPERLY PRESSED INTO PCB. B 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ± ANGULAR TOL A DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 7 OF 8 1 A 20 19 18 17 16 15 14 13 12 11 10 9 7 8 6 5 4 3 2 1 M M L L K DATE REV 2011/06/10 A INITIAL RELEASE 2011/06/15 A1 SHEET 1: REMOVED HEATSINK OPENING REFERENCE DIMENSIONS AND WEEK 52 REFERENCE; SHEET 4: ADDED NOTES POINTING TO THE INNER WALL COINED OVER THE COVER. 2011/07/22 B ADDED HOLES IN CAGE FOR LIGHTPIPES; MOVED DATE CODE; REVISED ROHS NOTE 5; CHANGED HEATSINK HEIGHT FROM 8.63 TO 6.5; TABULARIZED PCI, SAN, AND NETWORKING; AND ADDED HEATSINK HEIGHT WITH MODULE INSERTED. 2011/08/19 B1 UPDATED CAGE AND SPRING CLIP MODELS. 2012/10/25 C SHEET 1: REMOVED HEATSINKS, AND ALL DIMS AND ANNOTATIONS RELATING TO THEM, FROM ALL VIEWS; REMOVED NOTE 6; REMOVED EXPLODED VIEW; REMOVED PART NUMBER TABLE; ADDED TITLE. NEW SHEET 2: ISO VIEWS OF CAGE WITH NO HEATSINKS AND VIEWS WITH EACH OF FOUR TYPES AND SIZES OF HEATSINK; ANNOTATIONS ON EACH VIEW INDICATIING EACH HEATSINK TYPE AND SIZE; RIGHT SIDE VIEW WITH DIM OF HEATSINK HEIGHT; TABLE UNDER EACH VIEW WITH HEATSINK SIZES AND DIMS; NOTE 1; SHEET TITLE. NEW SHEET 3: ISO VIEWS OF CAGE WITH NO HEATSINKS AND VIEWS WITH EACH OF FOUR DIFFERENT TYPES OF HEATSINK; TABLES UNDER EACH VIEW WITH PART NUMBERS OF EACH SIZE; SHEET TITLE. J 2014/02/07 D H G DESCRIPTION J SHEET 1: REVISED ALL BASE CAGE DETAILS AND VIEWS FROM 111112-0232 TO 74754-0220. REMOVED INSERTION FORCE INTO PCB FROM NOTE 2. REVISED NOTE 4: "WAS" WELD SPOT WILL SHOW SLIGHT MATERIAL DISCOLORATION. "NOW READS" WELD SPOT MAY SHOW SLIGHT MATERIAL DISCOLORATION. SHEET 2: REVISED ALL HEAT SINK CAGE ASSEMBLY OPTIONS, ADDED OPEN TOP VIEW WITH DIMENSIONS, AND REAR LEG OPTION VIEW. ADDED SHEET 3 WITH ZSFP+ OPTIONS SHEET 4: ADDED PART NUMBERS 747540220, 1001130220. UPDATED TITLE BLOCK. 2014/08/13 E SHEET 1: ADDED "REF" TO DIM 10.85 AND 28.25. ADDED 14.0 ±0.1. MOVED "MINIMUM PCB THICKNESS" NOTES FROM SHEET 1 TO SHEETS 5 AND 6. 2014/08/21 F SHEET 1: ADDED 747540247 NO NEED PRINTED @C6. SHEET 1: ADDED P/N AND DATE CODE PRINTED NOTE @D11. SHEET 4: ADDED P/N 747540247 IN TABLE @I18. 2015/02/26 G SHEET 3: ADDED NOTE 1 "UNDER BELLY GASKET IS UL94 V-0 RATED." SHEET 4: ADDED "5 WELD POINTS" INTO 747540220 @I17. SHEET 4: ADDED P/N 747540222 @I17. SHEET 7: ADDED NOTE 2 "CAGE LEG STANDOFF WILL PIERCE BELLY GASKET WHEN PROPERLY PRESSED INTO PCB." F 2015/08/26 H E 2021/06/24 J K H G F SHEET 2: E3 : ADDED NEW CUSTOM FIN HEATSINK ISOVIEW SHEET 4: E3 : ADDED PART NO. 111112-6221 ISOVIEW MODIFIED PCB LAYOUT PER SFF-8433 SHEET 5: K19 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 D17 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 SHEET 6: G19 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 B18 : CHANGED TURE POSITION OF PCB HOLES FORM 0.05 TO 0.1 E OBSOLETED P/N ARE REMOVED 1111126221, 1111121220, 1111123220, 1111124220, 1111125220, 1111126220, 1111128220, 1111129220. D D C THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION C DIMENSION UNITS SCALE mm 2:1 CURRENT REV DESC: OBSOLETED PART NUMBER AS PER PCN#509457. GENERAL TOLERANCES (UNLESS SPECIFIED) MM B 4 PLACES ± ± 3 PLACES ± ± 2 PLACES ± 0.13 ± ± 0.25 ± 1 PLACE 0 PLACES ± ± ANGULAR TOL A DOCUMENT STATUS FORMAT: Eng-lega-master-tb-prod-D REVISION: E1 DATE: 2021/05/01 19 P1 RELEASE DATE 18 2021/11/25 17 16 ± DRAFT WHERE APPLICABLE MUST REMAIN WITHIN DIMENSIONS 12:19:18 15 14 13 12 11 10 9 8 7 SFP+ 1X2 CAGE, .120 INCH PRESS FIT, HEAT SINK, EMI SPRING FINGERS INCH ° EC NO: 680890 DRWN: SANTHN CHK'D: GGA APPR: GGA INITIAL REVISION: DRWN: JERWIN APPR: THIRD ANGLE PROJECTION 6 2021/06/24 2021/11/25 2021/11/25 B PRODUCT CUSTOMER DRAWING DOC TYPE DOC PART REVISION DOCUMENT NUMBER 2013/11/21 DRAWING SERIES D-SIZE 111112 5 SD-111112-2220 MATERIAL NUMBER GENERAL MARKET 3 J SHEET NUMBER CUSTOMER SEE SHEET 4 4 PSD 001 2 8 OF 8 1 A