87427-0203

PRODUCT SPECIFICATION MINIFIT JR CONNECTOR SYSTEM / 87427 SERIES 1.0 SCOPE This specification covers the 4.2mm centerline tin plated Mini-Fit Jr connector series terminated with 16 to 28 AWG wire using crimp technology. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER(S) Part Number Product Description 87427-**0* 87427-**1* 87427-**4* 5557 SERIES 5556 SERIES Mini-Fit Jr. Right Angle Header without Mounting Flanges Mini-Fit Jr. Right Angle Header with Mounting Flanges Mini-Fit Jr. Vertical Header Receptacle, Mini-Fit Jr. Series Female Crimp Terminal 2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS See the appropriate sales drawings for information on dimensions, materials, plating and markings. 2.3 SAFETY AGENCY APPROVALS UL File: E29179 CSA Certificate: LR19980 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS See the Sales Drawings and the other sections of this specification for the necessary referenced documents and specifications. REVISION: A4 ECR/ECN INFORMATION: EC No: UCP2014-1969 DATE: 2013/11/04 DOCUMENT NUMBER: PS-87427-0001 TITLE: MINIFIT JR RIGHT ANGLE & VERTICAL CONNECTOR WITH & WITHOUT MOUNTING FLANGES SHEET No. 1 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: NNGUYEN JBELL FSMITH TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 4.0 RATINGS 4.1 VOLTAGE 600 Volts AC (RMS)(or 600 Volts DC) 4.2 MAXIMUM CURRENT RATING AND APPLICABLE WIRES CKT AWG AWG #16 AWG #18 AWG #20 AWG #22 AWG #24 AWG #26 AWG #28 2&3 9A 9A 7A 5A 4A 3A 2A Current (Amperes) 4&6 7-10 12-24 8A 8A 6A 4A 3A 2A 1A 7A 7A 5A 4A 3A 2A 1A Max insulation Diameter 6A 6A 5A 4A 3A 2A 1A 3.10 MAX 1.80 MAX Ratings shown represent MAXIMUM current carrying capacity of a fully loaded connector with all circuits powered. Ratings are based on a 30°C maximum temperature rise limit over ambient (room temperature). Above charts are intended as a guideline. Current rating is application dependent. Appropriate de-rating is required depending on factors such as circuit size, ambient temperature, smaller copper weight of PCB traces, gross heating from adjacent modules or components and other factors that influence connector performance. Wire size and stranding, tin coated or bare copper, wire length and crimp quality are other factors that influence current rating. Current ratings apply to Brass 5556 crimp terminals only. 4.3 TEMPERATURE Operating*: - 40 °C to + 105 °C *Including 30 °C terminal temperature at rated current. 5.0 PERFORMANCE 5.1 ELECTRICAL REQUIREMENTS ITEM DESCRIPTION 1 Contact Resistance TEST CONDITION REQUIREMENT Mate connectors: apply a maximum voltage of 20 mV and a current of 100 mA. Wire resistance shall be removed from 10 mΩ Max (Initial) the measured value. 2 Insulation Resistance 3 Dielectric Withstanding Voltage REVISION: A4 ECR/ECN INFORMATION: EC No: UCP2014-1969 DATE: 2013/11/04 DOCUMENT NUMBER: PS-87427-0001 Mate connectors: apply a voltage of 500 VDC between adjacent terminals and between terminals to ground. 1000 MΩ Min Mate connectors: apply a voltage of 2200 VAC for 1 minute between adjacent terminals and between terminals to ground. TITLE: No breakdown; current leakage < 5 mA MINIFIT JR RIGHT ANGLE & VERTICAL CONNECTOR WITH & WITHOUT MOUNTING FLANGES SHEET No. 2 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: NNGUYEN JBELL FSMITH TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 5.2 MECHANICAL REQUIREMENTS ITEM DESCRIPTION 4 Connector Mate and Unmating Forces 5 6 TEST CONDITION REQUIREMENT Mate and unmate connector at a rate of 25 ± 6 mm (1 ± ¼ inch) per minute. See chart in Section 8.0 Mount the crimped terminal apply an axial pullout force on the wire at a rate of 25 ± 6 mm (1 ± ¼ inch) per minute. AWG # 16 9.0 kgf Min AWG # 18 9.0 kgf Min AWG # 20 6.0 kgf Min AWG # 22 4.0 kgf Min AWG # 24 3.0 kgf Min AWG # 26 2.0 kgf Min AWG # 28 1.0 kgf Min Wire pull out force is applicator dependent. Reference relevant Molex application tooling specification Wire Pullout Force (Axial) Terminal Insertion Insert crimped terminal into the housing Forces 1.5 kgf Min. 7 Terminal Retention Force (in Housing) Axial pullout force on the crimp terminal in the housing at a rate of 25 ± 6 mm (1 ± ¼ inch) per minute. 8 Pin Retention Force (in Housing) Axial push force at the speed rate of 25 ± 6 mm (1 ± ¼ inch) per minute. 9 Thumblatch Operation Force in Housing Depress latch at a speed rate of 25 ± 6 mm (1 ± ¼ inch) per minute. 1.7 kgf Max. 10 Thumblatch Yield Strength Mate loaded connector fully. Pull apart via wires at a speed rate of 25 ± 6 mm (1 ± ¼ inch) per minute. 7.0 kgf Min. 11 Normal Force 12 Durability 3.0 kgf Min MINIMUM retention force 1.0 kgf Min MINIMUM retention force Insert split test fixture into female terminal. Apply force perpendicular to terminal sides at a speed rate of 2.54 mm (.1 inch) per minute. When mated up to 30 cycles repeatedly by the rate of 10 cycles per minute. 375.0 gf Max. Contact Resistance 20 mΩ MAXIMUM * *Change from initial REVISION: A4 ECR/ECN INFORMATION: EC No: UCP2014-1969 DATE: 2013/11/04 DOCUMENT NUMBER: PS-87427-0001 TITLE: MINIFIT JR RIGHT ANGLE & VERTICAL CONNECTOR WITH & WITHOUT MOUNTING FLANGES SHEET No. 3 of 7 CREATED / REVISED BY: CHECKED BY: APPROVED BY: NNGUYEN JBELL FSMITH TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC PRODUCT SPECIFICATION 5.3 ENVIRONMENTAL REQUIREMENTS ITEM 13 DESCRIPTION Shock (Mechanical) TEST CONDITION REQUIREMENT Appearance Contact Resistance Discontinuity No Damage 20 mΩ MAXIMUM *